Omid Habibzadeh-Bigdarvish
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Omid Habibzadeh-Bigdarvish has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Gang Lei
5 shared publicationsTeng Li
5 shared publicationsXinbao Yu
4 shared publications- Xinbao Yu
Department of Civil Engineering, University of Texas, Arlington, TX 76019, USA
3 shared publications - Gang Lei
Department of Civil Engineering, The University of Texas at Arlington, Arlington, Texas, USA
2 shared publications Nice Kaneza
Graduate Research Assistant, Dept. of Civil Engineering, Univ. of Texas at Arlington, Arlington, TX.
2 shared publications
Latest Publications
- 30 April 2023
- Published by Taylor & Francis in Experimental Heat Transfer
- Vol. 37 (6) , 807-829
Interface heat transfer for hydronic heating: heating tests of concrete blocks and numerical simulations
A comprehensive understanding of the heat transfer mechanism of hydronically-heated structures is crucial to predicting their heating performance. However, few studies considered the heat transfer at the interface of heating pipe and host material. In this paper, heat transfer at two critical interfaces for hydronically-heated concrete structures, e.g. pipe-concrete interface and concrete-air interface, has been tested and analyzed. Two concrete blocks, one with an embedded cross-linked polyethylene (PEX) pipe and one with an attached PEX pipe, were fabricated to represent heated bridge decks for the heat transfer study. The two blocks were tested inside a freezer box in a series of heating response tests at varied room and fluid temperatures. Measured temperatures at different depths were used to find the convection heat transfer coefficient and the thermal contact conductance between the concrete and PEX pipe through equations developed via finite difference method (FDM). Finite element models (FEM) of the two blocks were developed to verify the thermal contact values derived from a 1-D thermal resistance model. A comprehensive analysis of the temperature response of the models was performed, especially at the two interfaces, and the FEM models were able to predict the lab measurements accurately. The obtained contact heat transfer coefficient and the FEM models can be used for all hydronically-heated structures.
- 30 April 2023
- Published by Taylor & Francis in Experimental Heat Transfer
- Vol. 37 (6) , 807-829
Interface heat transfer for hydronic heating: heating tests of concrete blocks and numerical simulations
A comprehensive understanding of the heat transfer mechanism of hydronically-heated structures is crucial to predicting their heating performance. However, few studies considered the heat transfer at the interface of heating pipe and host material. In this paper, heat transfer at two critical interfaces for hydronically-heated concrete structures, e.g. pipe-concrete interface and concrete-air interface, has been tested and analyzed. Two concrete blocks, one with an embedded cross-linked polyethylene (PEX) pipe and one with an attached PEX pipe, were fabricated to represent heated bridge decks for the heat transfer study. The two blocks were tested inside a freezer box in a series of heating response tests at varied room and fluid temperatures. Measured temperatures at different depths were used to find the convection heat transfer coefficient and the thermal contact conductance between the concrete and PEX pipe through equations developed via finite difference method (FDM). Finite element models (FEM) of the two blocks were developed to verify the thermal contact values derived from a 1-D thermal resistance model. A comprehensive analysis of the temperature response of the models was performed, especially at the two interfaces, and the FEM models were able to predict the lab measurements accurately. The obtained contact heat transfer coefficient and the FEM models can be used for all hydronically-heated structures.
- 17 September 2021
- Published by Springer Nature
- p. 261-273
De-icing Test of the Externally Heated Geothermal Bridge in Texas
- 17 September 2021
- Published by Springer Nature
- p. 261-273
De-icing Test of the Externally Heated Geothermal Bridge in Texas
- 1 December 2020
- Published by Elsevier in Journal of Cleaner Production
- Vol. 275
Feasibility study of a new attached multi-loop CO2 heat pipe for bridge deck de-icing using geothermal energy
- 1 December 2020
- Published by Elsevier in Journal of Cleaner Production
- Vol. 275
Feasibility study of a new attached multi-loop CO2 heat pipe for bridge deck de-icing using geothermal energy
- 21 February 2020
- Published by American Society of Civil Engineers (ASCE)
- p. 402-409
Development and Validation of a Double-Column Soil Cell for 1-D Heating Test
Recent developments of energy piles and soil borehole thermal energy storage have increased the concern of the behavior of soils under thermal loads. Laboratory heating and cooling tests of soils are subject to the ambient temperature effect due to inadequate thermal insulation. Thus, the test data are prone to errors due to such boundary effects. A double-column soil test cell was developed, and the test results of dry sand showed 1-D heating was obtained in the inner soil column. In this study, the heat cell was modified that a hydronic heating exchanger was attached to the bottom of the column. The dry fine-grained sand was first tested to validate the measured temperature field with theoretical predictions. Then the coarse-grained sand was then tested to investigate its temperature performance. The results showed that both fine/coarse-grained sand can maintain 1-D heat transfer in the inner column cell. This test cell is promising to study the soil thermal and hydro behavior under controlled 1-D thermal gradients.
- 21 February 2020
- Published by American Society of Civil Engineers (ASCE)
- p. 402-409
Development and Validation of a Double-Column Soil Cell for 1-D Heating Test
Recent developments of energy piles and soil borehole thermal energy storage have increased the concern of the behavior of soils under thermal loads. Laboratory heating and cooling tests of soils are subject to the ambient temperature effect due to inadequate thermal insulation. Thus, the test data are prone to errors due to such boundary effects. A double-column soil test cell was developed, and the test results of dry sand showed 1-D heating was obtained in the inner soil column. In this study, the heat cell was modified that a hydronic heating exchanger was attached to the bottom of the column. The dry fine-grained sand was first tested to validate the measured temperature field with theoretical predictions. Then the coarse-grained sand was then tested to investigate its temperature performance. The results showed that both fine/coarse-grained sand can maintain 1-D heat transfer in the inner column cell. This test cell is promising to study the soil thermal and hydro behavior under controlled 1-D thermal gradients.
- 21 March 2019
- Published by American Society of Civil Engineers (ASCE)
- p. 682-690
Development of a One-Dimensional Heating Soil Test Cell
Coupled thermo-hydro-mechanical (THM) processes are of great importance to geothermal, hydrology, and geotechnical engineering applications. There is a lack of laboratory testing apparatuses to measure the THM processes under controlled true 1-D heating conditions. This paper develops a modified 1-D heat soil cell for the study of THM processes. This soil cell consists of a double acrylic test column and a heating plate at the bottom plate to control the temperature gradient. The test cells are equipped with thermocouples to monitor the temperature changes during heating processes. Two tests are conducted with the boundary temperatures at 50 and 70°C, respectively. Test results show nearly linear axial and radial temperature profiles in the inner soil column. The temperature profiles for the outer soil column are also obtained, showing a significant influence of room temperature on the outer column. The time to reach steady-state temperature for both tests is the same, which is 6 h. A infrared camera was also used to visualize the temperature distribution of the column top surface.
- 21 March 2019
- Published by American Society of Civil Engineers (ASCE)
- p. 682-690
Development of a One-Dimensional Heating Soil Test Cell
Coupled thermo-hydro-mechanical (THM) processes are of great importance to geothermal, hydrology, and geotechnical engineering applications. There is a lack of laboratory testing apparatuses to measure the THM processes under controlled true 1-D heating conditions. This paper develops a modified 1-D heat soil cell for the study of THM processes. This soil cell consists of a double acrylic test column and a heating plate at the bottom plate to control the temperature gradient. The test cells are equipped with thermocouples to monitor the temperature changes during heating processes. Two tests are conducted with the boundary temperatures at 50 and 70°C, respectively. Test results show nearly linear axial and radial temperature profiles in the inner soil column. The temperature profiles for the outer soil column are also obtained, showing a significant influence of room temperature on the outer column. The time to reach steady-state temperature for both tests is the same, which is 6 h. A infrared camera was also used to visualize the temperature distribution of the column top surface.
- Open Access
- 1 December 2018
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
- Vol. 10 (6) , 1145-1153
Assessment of thermal behaviour of thermo-active diaphragm walls based on monitoring data
- 1 December 2018
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
- Vol. 10 (6) , 1145-1153
Open AccessAssessment of thermal behaviour of thermo-active diaphragm walls based on monitoring data