Shazia Farman Ali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shazia Farman Ali has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Aaron Gillich
Net Zero Building Centre, School of the Built Environment and Architecture, London South Bank University, London, UK
1 shared publicationAlex Paurine
School of the Built Environment and Architecture, London South Bank University
1 shared publicationH. Yeung
Process Systems Engineering Group, School of Engineering, Cranfield University , Bedfordshire, UK
1 shared publicationHoi Yeung
Department of Offshore, Process and Energy Engineering Cranfield University Cranfield Bedfordshire MK43 0AL UK
1 shared publication- Hoi Yeung
Centre for Thermal Energy Systems and Materials, Cranfield University, Cranfield MK43 0AL, UK
1 shared publication - Maria Mavroulidou
School of Engineering and Design, London South Bank University, 103 Borough Road, London SE1 0AA, UK
1 shared publication
Latest Publications
- Open Access
- 21 November 2022
- Published by University of the Aegean
A review on the potential use of flammable gases from sewage systems as a source of energy
The demand for natural resources has increased exponentially due to the consistent growth of the global population and urbanization. This has resulted to considerable environmental challenges that are potentially affecting the global sustainable development goals. Therefore, it is important to develop sustainable strategies to manage urban wastes as well as produce and utilize energy. Flammable gases being generated from the sewage systems can be a prospective renewable resource of energy. However, existing studies suggest that the potential of sewage gas utilization for energy production has not been explored effectively. This paper focuses on identifying key design elements of sewage systems in an Anaerobic Digester (AD) to optimize the process of conversion of human waste into energy source. The paper uses a kinetic model to describe the fermentation process and thus evaluating the effect of key parameters on biogas (specifically methane) gases production in an anaerobic digester environment.
- 21 November 2022
- Published by University of the Aegean
Open AccessA review on the potential use of flammable gases from sewage systems as a source of energy
The demand for natural resources has increased exponentially due to the consistent growth of the global population and urbanization. This has resulted to considerable environmental challenges that are potentially affecting the global sustainable development goals. Therefore, it is important to develop sustainable strategies to manage urban wastes as well as produce and utilize energy. Flammable gases being generated from the sewage systems can be a prospective renewable resource of energy. However, existing studies suggest that the potential of sewage gas utilization for energy production has not been explored effectively. This paper focuses on identifying key design elements of sewage systems in an Anaerobic Digester (AD) to optimize the process of conversion of human waste into energy source. The paper uses a kinetic model to describe the fermentation process and thus evaluating the effect of key parameters on biogas (specifically methane) gases production in an anaerobic digester environment.
- Open Access
- 29 July 2021
- Published by SAGE Publications in Building Services Engineering Research & Technology
- Vol. 42 (6) , 715-732
Opportunities to decarbonize heat in the UK using Urban Wastewater Heat Recovery
By 2050, the UK government plans to create ‘Net zero society’. 1 To meet this ambitious target, the deployment of low carbon technologies is an urgent priority. The low carbon heat recovery technologies such as heat recovery from sewage via heat pump can play an important role. It is based on recovering heat from the sewage that is added by the consumer, used and flushed in the sewer. This technology is currently successfully operating in many cities around the world. In the UK, there is also a rising interest to explore this technology after successful sewage heat recovery demonstration project at Borders College, Galashiels, Scotland. 2 However, further experimental research is needed to build the evidence base, replicate, and de-risk the concept elsewhere in the UK. The Home Energy 4 Tomorrow (HE4T) project at London South Bank University was created to address this evidence gap. This is the fourth article in the series of outputs on sewage heat recovery and presents some results using sewage data from the UK’s capital London. These data are scarce and provide useful information on the variation of flows and temperatures encountered in the sewers of the UK’s capital. Lastly, we discuss the recoverable heat potential along with policy implications for the UK heat strategy. Practical application: This work focuses and accentuate that in order to meet climate change targets, substantial improvements can come by heat recovery from the raw (influent) and treated wastewater (effluent from wastewater treatment plant) that is still unexploited in the UK. The estimation presented indicates that there is much theoretical potential in the UK with significant opportunity for future energy and revenue retrieval along with GHGs emission reduction in the longer term to fulfil the ‘net zero’ objective. This work aims to raise awareness and seek support to promote pilot scale studies to help demonstrate technical and economic feasibility in the building industry.
- 29 July 2021
- Published by SAGE Publications in Building Services Engineering Research & Technology
- Vol. 42 (6) , 715-732
Open AccessOpportunities to decarbonize heat in the UK using Urban Wastewater Heat Recovery
By 2050, the UK government plans to create ‘Net zero society’. 1 To meet this ambitious target, the deployment of low carbon technologies is an urgent priority. The low carbon heat recovery technologies such as heat recovery from sewage via heat pump can play an important role. It is based on recovering heat from the sewage that is added by the consumer, used and flushed in the sewer. This technology is currently successfully operating in many cities around the world. In the UK, there is also a rising interest to explore this technology after successful sewage heat recovery demonstration project at Borders College, Galashiels, Scotland. 2 However, further experimental research is needed to build the evidence base, replicate, and de-risk the concept elsewhere in the UK. The Home Energy 4 Tomorrow (HE4T) project at London South Bank University was created to address this evidence gap. This is the fourth article in the series of outputs on sewage heat recovery and presents some results using sewage data from the UK’s capital London. These data are scarce and provide useful information on the variation of flows and temperatures encountered in the sewers of the UK’s capital. Lastly, we discuss the recoverable heat potential along with policy implications for the UK heat strategy. Practical application: This work focuses and accentuate that in order to meet climate change targets, substantial improvements can come by heat recovery from the raw (influent) and treated wastewater (effluent from wastewater treatment plant) that is still unexploited in the UK. The estimation presented indicates that there is much theoretical potential in the UK with significant opportunity for future energy and revenue retrieval along with GHGs emission reduction in the longer term to fulfil the ‘net zero’ objective. This work aims to raise awareness and seek support to promote pilot scale studies to help demonstrate technical and economic feasibility in the building industry.
- 1 April 2015
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 44, 117-131
Greenhouse effect reduction by recovering energy from waste landfills in Pakistan
- 1 April 2015
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 44, 117-131
Greenhouse effect reduction by recovering energy from waste landfills in Pakistan
- Open Access
- 23 January 2015
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 202 (6) , 823-842
Experimental Study of Two-Phase Air–Water Flow in Large-Diameter Vertical Pipes
Recently, due to an increase in production demand in nuclear and oil and gas industries, the requirement to migrate toward larger pipe sizes for future developments has become essential. However, it is interesting to note that almost all the research on two-phase gas–liquid flow in vertical pipe upflow is based on small-diameter pipes (D ≤ 100 mm), and the experimental work on the two-phase gas–liquid flow in large-diameter (D > 100 mm) vertical pipes is scarce. Under the above circumstances, the application of modeling tools/correlations based on small-diameter pipes in predicting flow behavior (flow pattern, void fraction, and pressure gradient) poses severe challenges in terms of accuracy. The results presented in this article are motivated by the need to introduce the research work done to the industries where the data pertaining to large-diameter vertical pipes are scarce and there is a lack of understanding of two-phase gas-liquid flow behavior in large-diameter (D > 100 mm) vertical pipes. The unique aspect of the results presented here is that the experimental data have been generated for a 254-mm inner diameter vertical pipe that forms an excellent basis for the assessment of modeling tools/correlations. This article (i) presents the results of a systematic investigation of the flow patterns in large-diameter vertical pipes and identifies the transition between subsequent flow patterns, (ii) compares it directly with the existing large- (150 mm) and small-diameter data (28 mm and 32 mm) in the same air–water superficial velocity range, (iii) exemplifies that the existing available empirical correlations/models/codes are significantly in error when applied to large-diameter vertical pipes for predictions, and last (iv) assesses the predictive capability of a well-known commercial multiphase flow simulator.
- 23 January 2015
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 202 (6) , 823-842
Open AccessExperimental Study of Two-Phase Air–Water Flow in Large-Diameter Vertical Pipes
Recently, due to an increase in production demand in nuclear and oil and gas industries, the requirement to migrate toward larger pipe sizes for future developments has become essential. However, it is interesting to note that almost all the research on two-phase gas–liquid flow in vertical pipe upflow is based on small-diameter pipes (D ≤ 100 mm), and the experimental work on the two-phase gas–liquid flow in large-diameter (D > 100 mm) vertical pipes is scarce. Under the above circumstances, the application of modeling tools/correlations based on small-diameter pipes in predicting flow behavior (flow pattern, void fraction, and pressure gradient) poses severe challenges in terms of accuracy. The results presented in this article are motivated by the need to introduce the research work done to the industries where the data pertaining to large-diameter vertical pipes are scarce and there is a lack of understanding of two-phase gas-liquid flow behavior in large-diameter (D > 100 mm) vertical pipes. The unique aspect of the results presented here is that the experimental data have been generated for a 254-mm inner diameter vertical pipe that forms an excellent basis for the assessment of modeling tools/correlations. This article (i) presents the results of a systematic investigation of the flow patterns in large-diameter vertical pipes and identifies the transition between subsequent flow patterns, (ii) compares it directly with the existing large- (150 mm) and small-diameter data (28 mm and 32 mm) in the same air–water superficial velocity range, (iii) exemplifies that the existing available empirical correlations/models/codes are significantly in error when applied to large-diameter vertical pipes for predictions, and last (iv) assesses the predictive capability of a well-known commercial multiphase flow simulator.
- 19 June 2013
- Published by Wiley in Asia-Pacific Journal of Chemical Engineering
- Vol. 9 (1) , 105-116
Two‐phase flow patterns in large diameter vertical pipes
An experimental investigation of adiabatic upward co‐current air–water two‐phase flow has been carried out to determine the flow patterns in a 12.2=m‐high and 250=mm nominal diameter vertical pipe. The visual observations of flow patterns were supplemented by statistical analysis of the time‐averaged void fraction determined by pressure drop method. Four flow patterns were identified in the vertical test section, namely dispersed bubbly, bubbly, agitated bubblyand churn/forth flow within the experimental superficial velocity range ( ja = 0.18–2.2 m/s and jw = 0.18–1.2 m/s). Conventional slug flow consisting of smooth bullet‐shaped bubbles (Taylor bubble) and liquid slugs was never observed; instead, agitated bubbly flow was the most dominant flow pattern in relevant superficial velocity range. On the basis of the visual and statistically extracted information, a flow pattern map was developed and compared with the existing flow pattern maps. Available flow regime transition models compared against the present experimental data yielded poor agreement with none of the existing models predicting the transitions as a whole. A satisfactory agreement was obtained with other large diameter studies with inconsistencies mainly attributable to confusion in the identification of the flow patterns. © 2013 Curtin University of Technology and John Wiley & Sons, Ltd.
- 19 June 2013
- Published by Wiley in Asia-Pacific Journal of Chemical Engineering
- Vol. 9 (1) , 105-116
Two‐phase flow patterns in large diameter vertical pipes
An experimental investigation of adiabatic upward co‐current air–water two‐phase flow has been carried out to determine the flow patterns in a 12.2=m‐high and 250=mm nominal diameter vertical pipe. The visual observations of flow patterns were supplemented by statistical analysis of the time‐averaged void fraction determined by pressure drop method. Four flow patterns were identified in the vertical test section, namely dispersed bubbly, bubbly, agitated bubblyand churn/forth flow within the experimental superficial velocity range ( ja = 0.18–2.2 m/s and jw = 0.18–1.2 m/s). Conventional slug flow consisting of smooth bullet‐shaped bubbles (Taylor bubble) and liquid slugs was never observed; instead, agitated bubbly flow was the most dominant flow pattern in relevant superficial velocity range. On the basis of the visual and statistically extracted information, a flow pattern map was developed and compared with the existing flow pattern maps. Available flow regime transition models compared against the present experimental data yielded poor agreement with none of the existing models predicting the transitions as a whole. A satisfactory agreement was obtained with other large diameter studies with inconsistencies mainly attributable to confusion in the identification of the flow patterns. © 2013 Curtin University of Technology and John Wiley & Sons, Ltd.
- 7 June 2010
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 28 (11) , 1079-1095
Experimental Investigation and Numerical Simulation of Two-Phase Flow in a Large-Diameter Horizontal Flow Line Vertical Riser
As oil and gas field development moves further into deep seas, maximizing hydrocarbon extraction at an acceptable cost is one of the greatest challenges facing the industry today. In this regard, considerable attention has been given to understanding the flow behavior in long and deep flow line risers of different topologies through transient multiphase simulation. However, the application of the large diameter to the above scenario is still an unresolved issue creating a great deal of uncertainty. This is mainly due to the limitation of the available experimental and field data being confined to much smaller diameters. In view of the aforementioned, an experimental campaign to investigate the flow behavior in a 254-mm nominal-diameter horizontal flow line vertical riser has been performed. A numerical model to study the dynamic behavior of the large-diameter horizontal flow line vertical riser system is also developed using OLGA software with the intention of identifying the capability of this software. This article presents the comparison of the simulation and experimental data in terms of near riser base and flow line pressure variations along with flow regime predictions. The existence of the multiple roots in the OLGA code is also reported for the first time. Additionally, a review on the state-of-the-art application of the code and analysis of the numerical experiment performance of the code are included.
- 7 June 2010
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 28 (11) , 1079-1095
Experimental Investigation and Numerical Simulation of Two-Phase Flow in a Large-Diameter Horizontal Flow Line Vertical Riser
As oil and gas field development moves further into deep seas, maximizing hydrocarbon extraction at an acceptable cost is one of the greatest challenges facing the industry today. In this regard, considerable attention has been given to understanding the flow behavior in long and deep flow line risers of different topologies through transient multiphase simulation. However, the application of the large diameter to the above scenario is still an unresolved issue creating a great deal of uncertainty. This is mainly due to the limitation of the available experimental and field data being confined to much smaller diameters. In view of the aforementioned, an experimental campaign to investigate the flow behavior in a 254-mm nominal-diameter horizontal flow line vertical riser has been performed. A numerical model to study the dynamic behavior of the large-diameter horizontal flow line vertical riser system is also developed using OLGA software with the intention of identifying the capability of this software. This article presents the comparison of the simulation and experimental data in terms of near riser base and flow line pressure variations along with flow regime predictions. The existence of the multiple roots in the OLGA code is also reported for the first time. Additionally, a review on the state-of-the-art application of the code and analysis of the numerical experiment performance of the code are included.