Junsung Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Junsung Park has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Pyosoo Kim
POSCO ICT Co., Ltd., POSCO R&D Center, Seoul, Korea
1 shared publication- Sanghyuk Lee
Seoul National University
1 shared publication - Sewan Choi
Department of Electrical and Information Engineering, Seoul National University of Science and Technology, Seoul, South Korea
1 shared publication - Sung-Min Hong
Gwangju Institute of Science and Technology, Gwangju, Republic of Korea
1 shared publication
Latest Publications
- Open Access
- 8 March 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (7) , Q3116-Q3121
Simulation Study of Enhancement Mode Multi-Gate Vertical Gallium Oxide MOSFETs
In this study, the state-of-the-art vertical gallium oxide MOSFET with the fin shaped source is numerically investigated. With the simulation environment, whose results for the electrical characteristics are in close agreement with the available experimental results, the impact of the fin shape is studied. It is found that a rectangular fin with a height of 1.0 μm and a width of 0.3 μm can give a low on-resistance per unit area and a low drain-induced barrier lowering (DIBL) simultaneously. Moreover, the tapered fins are simulated to estimate the sensitivity of the on-resistance, the DIBL, and the subthreshold slope.
- 8 March 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (7) , Q3116-Q3121
Open AccessSimulation Study of Enhancement Mode Multi-Gate Vertical Gallium Oxide MOSFETs
In this study, the state-of-the-art vertical gallium oxide MOSFET with the fin shaped source is numerically investigated. With the simulation environment, whose results for the electrical characteristics are in close agreement with the available experimental results, the impact of the fin shape is studied. It is found that a rectangular fin with a height of 1.0 μm and a width of 0.3 μm can give a low on-resistance per unit area and a low drain-induced barrier lowering (DIBL) simultaneously. Moreover, the tapered fins are simulated to estimate the sensitivity of the on-resistance, the DIBL, and the subthreshold slope.
- 1 May 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21506078,p. 2844-2851
High step-up interleaved boost converters using voltage multiplier cells
In this paper non-isolated interleaved DC-DC converters are proposed for high-step up application. The proposed converter has the following advantages: 1) Doubled voltage conversion ratio of the basic configuration (N=l) compared to the conventional boost converter 2) Low input current ripple, reduced size of the passive component and current stresses of switches due to interleaved structure 3) Increased flexibility in device selection by adjusting the number of voltage multiplier cells. Both hard-switching and soft-switching versions are proposed and compared each other. Experimental results from lkW prototypes are provided to validate the proposed concept.
- 1 May 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21506078,p. 2844-2851
High step-up interleaved boost converters using voltage multiplier cells
In this paper non-isolated interleaved DC-DC converters are proposed for high-step up application. The proposed converter has the following advantages: 1) Doubled voltage conversion ratio of the basic configuration (N=l) compared to the conventional boost converter 2) Low input current ripple, reduced size of the passive component and current stresses of switches due to interleaved structure 3) Increased flexibility in device selection by adjusting the number of voltage multiplier cells. Both hard-switching and soft-switching versions are proposed and compared each other. Experimental results from lkW prototypes are provided to validate the proposed concept.