Sigamani Saravanan
Research Subjects
Research Interests
Sigamani Saravanan has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
R.S. Dubey
5 shared publications- Gabbita Venkata Satya Subbaroy Sarma
Department of Physics, Malla Reddy Engineering College, Dhulapally-500 100, Secundrabad (TL), India
4 shared publications - Raghvendra Sarvjeet Dubey
S.B. Jain Institute of Technology, Management, and Research, India
3 shared publications B. Ananda Kumar
2 shared publicationsM. Geetha
Department of Physics, R P Sarathy Institute of Technology, Salem (TN)-636 305, India
2 shared publicationsR. S. Dubey
2 shared publications
Latest Publications
- Open Access
- 30 September 2026
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 15 (3) , 11-17
Sol-gel Spin-coated SiO2 Multilayers for Anticorrosion Applications
A silicon dioxide (SiO2) film protects steel or other metals by acting as a highly dense, impermeable barrier against corrosive agents. SiO2 thin-film coatings are widely used for their superior performance and economic benefits. In this work, a sol-gel-synthesized and spin-coated SiO2 thin film was deposited on mild steel, which was calcined at 300°C. The prepared thin films were examined for their optical, structural, functional, morphological, elemental, and corrosion properties using XRD, FTIR, SEM, EDX, and EIS. The XRD spectrum revealed sharp, narrow diffraction peaks, confirming the quality of the crystallite-nature enhancement induced on the mild steel surface. In addition, sharp diffraction peaks confirmed the presence of SiO2 and the formation of an ultrafine crystal structure on the mild steel. FTIR transmittance spectrum shows the stretching vibration modes of the primary material, Si-O-Si, between 927 and 439 cm-1. The surface morphology of the prepared multilayer thin films was examined using SEM, whereas the EDX spectrum indicated the presence of Si and O. Finally, electrochemical impedance spectroscopy (EIS) is useful for evaluating strong anticorrosion properties. In future, the anticorrosion property can be studied by using TiO2, ZrO, and SiO2/TiO2 etc.
- 30 September 2026
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 15 (3) , 11-17
Open AccessSol-gel Spin-coated SiO2 Multilayers for Anticorrosion Applications
A silicon dioxide (SiO2) film protects steel or other metals by acting as a highly dense, impermeable barrier against corrosive agents. SiO2 thin-film coatings are widely used for their superior performance and economic benefits. In this work, a sol-gel-synthesized and spin-coated SiO2 thin film was deposited on mild steel, which was calcined at 300°C. The prepared thin films were examined for their optical, structural, functional, morphological, elemental, and corrosion properties using XRD, FTIR, SEM, EDX, and EIS. The XRD spectrum revealed sharp, narrow diffraction peaks, confirming the quality of the crystallite-nature enhancement induced on the mild steel surface. In addition, sharp diffraction peaks confirmed the presence of SiO2 and the formation of an ultrafine crystal structure on the mild steel. FTIR transmittance spectrum shows the stretching vibration modes of the primary material, Si-O-Si, between 927 and 439 cm-1. The surface morphology of the prepared multilayer thin films was examined using SEM, whereas the EDX spectrum indicated the presence of Si and O. Finally, electrochemical impedance spectroscopy (EIS) is useful for evaluating strong anticorrosion properties. In future, the anticorrosion property can be studied by using TiO2, ZrO, and SiO2/TiO2 etc.
- Open Access
- 1 July 2025
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 14 (2) , 178-181
Improvement of Quantum Efficiency and Photon Absorption from Electromagnetic Waves: Amorphous Silicon Thin Film Solar Cell
In this work, the performance of amorphous silicon (a-Si) thin film solar cell is demonstrated by integrating Ag at the bottom and indium tin oxide (ITO) nanostructures at the top, using the rigorous coupled wave analysis method. Among the various materials, amorphous silicon plays a significant role due to its ability to harvest photons from electromagnetic waves and its naturally abundant. The integration of photonic (ITO) and plasmonics (Ag) nanostructures are crucial for enhancing light-harvesting mechanisms through nanoscale engineering. In that way, the Fabry-Perot resonance, guided waves are helping to increase the life time of the light particle (photon) under transverse electric (TE) modes. Consequently, the localized field, surface excitation, and surface guided waves are also enhancing the light trapping mechanism under transverse magnetic (TM) field modes. Finally, the designed a-Si thin film solar cell yielded the highest conversion cell efficiency of 18.79% and a short-circuit current density of 28.57 mA/m2 in TE modes. However, TM modes received 18% of conversion efficiency and 27.46 mA/m2 of current density.
- 1 July 2025
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 14 (2) , 178-181
Open AccessImprovement of Quantum Efficiency and Photon Absorption from Electromagnetic Waves: Amorphous Silicon Thin Film Solar Cell
In this work, the performance of amorphous silicon (a-Si) thin film solar cell is demonstrated by integrating Ag at the bottom and indium tin oxide (ITO) nanostructures at the top, using the rigorous coupled wave analysis method. Among the various materials, amorphous silicon plays a significant role due to its ability to harvest photons from electromagnetic waves and its naturally abundant. The integration of photonic (ITO) and plasmonics (Ag) nanostructures are crucial for enhancing light-harvesting mechanisms through nanoscale engineering. In that way, the Fabry-Perot resonance, guided waves are helping to increase the life time of the light particle (photon) under transverse electric (TE) modes. Consequently, the localized field, surface excitation, and surface guided waves are also enhancing the light trapping mechanism under transverse magnetic (TM) field modes. Finally, the designed a-Si thin film solar cell yielded the highest conversion cell efficiency of 18.79% and a short-circuit current density of 28.57 mA/m2 in TE modes. However, TM modes received 18% of conversion efficiency and 27.46 mA/m2 of current density.
- Open Access
- 1 January 2025
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 14 (4) , 423-427
Photonic Light-Trapping Effects in Amorphous Silicon Thin-film Solar Cells with Top and Bottom Nanogratings
Among four different generations of solar cells, thin-film amorphous silicon (a-Si) solar cells are extensively used and garnering great interest in photovoltaic (PV) applications due to their cost-effectiveness, environmental friendly and versatility. In this study, we investigated the light-harvesting mechanism in a-Si solar cells by integrating nanostructures such as anti-reflection coatings (ARC), top and bottom nanogratings, and a distributed Bragg reflector (DBR). The layer thicknesses of indium tin-oxide (ITO, ARC), silicon (Si), and silicon dioxide were optimized using the quarter-wavelength formula. Electromagnetic simulations were also performed using the rigorous coupled wave analysis (RCWA) method under transverse electric (TE) and transverse magnetic (TM) polarization modes. This simulation works including four different cell structures were analyzed: a reference cell (Cell A), a top-grating-enhanced cell (Cell B), a bottom-grating-enhanced cell (Cell C), and a dual-grating cell (Cell D). Among these four cell structures, the nanogratings and DBR integration significantly improved light absorption (harvesting) by increasing optical path length, multiple scattering, and reducing reflection effects of the light particles (photons). The highest thin film a-Si solar cell performance yielded by Cell D which was 16.5% (TE) and 15.18% (TM), corresponding to enhancements of 357.7% and 343.5% current densities. These findings highlight the crucial role of nanostructures and DBR layers in enhancing photon collection in thin-film a-Si solar cells, providing a promising approach for high-efficiency photovoltaic devices.
- 1 January 2025
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 14 (4) , 423-427
Open AccessPhotonic Light-Trapping Effects in Amorphous Silicon Thin-film Solar Cells with Top and Bottom Nanogratings
Among four different generations of solar cells, thin-film amorphous silicon (a-Si) solar cells are extensively used and garnering great interest in photovoltaic (PV) applications due to their cost-effectiveness, environmental friendly and versatility. In this study, we investigated the light-harvesting mechanism in a-Si solar cells by integrating nanostructures such as anti-reflection coatings (ARC), top and bottom nanogratings, and a distributed Bragg reflector (DBR). The layer thicknesses of indium tin-oxide (ITO, ARC), silicon (Si), and silicon dioxide were optimized using the quarter-wavelength formula. Electromagnetic simulations were also performed using the rigorous coupled wave analysis (RCWA) method under transverse electric (TE) and transverse magnetic (TM) polarization modes. This simulation works including four different cell structures were analyzed: a reference cell (Cell A), a top-grating-enhanced cell (Cell B), a bottom-grating-enhanced cell (Cell C), and a dual-grating cell (Cell D). Among these four cell structures, the nanogratings and DBR integration significantly improved light absorption (harvesting) by increasing optical path length, multiple scattering, and reducing reflection effects of the light particles (photons). The highest thin film a-Si solar cell performance yielded by Cell D which was 16.5% (TE) and 15.18% (TM), corresponding to enhancements of 357.7% and 343.5% current densities. These findings highlight the crucial role of nanostructures and DBR layers in enhancing photon collection in thin-film a-Si solar cells, providing a promising approach for high-efficiency photovoltaic devices.
- Open Access
- 30 March 2024
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 36 (4) , 885-888
Sol-Gel Spin Coated Transparent Single-TiO2 and SiO2 Thin Film on Glass for Opto-electronic Applications
Great attention has been given on the sol-gel synthesis and spin-coating deposition techniques for the fabrication of various thin films. Because of its simple technique to fabricate dielectric (metal oxide) films using tetraethyl orthosilicate and titanium isopropoxide precursors. In this work, transparent single layer of SiO2 and TiO2 thin film was deposited on a glass substrate and characterized by FTIR, UV-visible spectroscopy, fluorescence and scanning electron microscopy techniques. The single layer thin film was mechanically stable and strong by adhering to glass substrates. The FTIR transmittance spectrum evidenced the existence of Si-O-Si and Ti-O-Ti at ~1100 and 1400 cm-1. The UV-visible absorbance spectra of single layer of SiO2 and TiO2 thin films showed strong absorption at below 00 nm. The excitation wavelength at 380 nm, the fluorescence spectra of both thin films showed the highest emission spectrum in between 733-798 nm. The SEM studies confirmed the smooth surface in both SiO2 and TiO2 layers. Further, it could be useful for various applications such as back reflector in solar cells, anti-reflection coatings, hydrophobic and anti-fogging materials.
- 30 March 2024
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 36 (4) , 885-888
Open AccessSol-Gel Spin Coated Transparent Single-TiO2 and SiO2 Thin Film on Glass for Opto-electronic Applications
Great attention has been given on the sol-gel synthesis and spin-coating deposition techniques for the fabrication of various thin films. Because of its simple technique to fabricate dielectric (metal oxide) films using tetraethyl orthosilicate and titanium isopropoxide precursors. In this work, transparent single layer of SiO2 and TiO2 thin film was deposited on a glass substrate and characterized by FTIR, UV-visible spectroscopy, fluorescence and scanning electron microscopy techniques. The single layer thin film was mechanically stable and strong by adhering to glass substrates. The FTIR transmittance spectrum evidenced the existence of Si-O-Si and Ti-O-Ti at ~1100 and 1400 cm-1. The UV-visible absorbance spectra of single layer of SiO2 and TiO2 thin films showed strong absorption at below 00 nm. The excitation wavelength at 380 nm, the fluorescence spectra of both thin films showed the highest emission spectrum in between 733-798 nm. The SEM studies confirmed the smooth surface in both SiO2 and TiO2 layers. Further, it could be useful for various applications such as back reflector in solar cells, anti-reflection coatings, hydrophobic and anti-fogging materials.
- Open Access
- 29 March 2024
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 13 (1) , 92-96
Green Synthesis of Barium Sulphate Nanostructures Using Azadirachta indica Leaf Extract
Green synthesis of nanostructures is a growing technology owing to its potential applications in various fields. The method is feasible, simple and non-toxic; it is a low-cost strategy. It meets the standards of green chemistry, high crystalline nature and morphological structures. In this work, green synthesis of barium sulphate nanostructure was carried out by using Azadirachta indica (neem) leaf extract, barium chloride dehydrates and anhydrous sodium sulphate as source materials, by co-precipitation method. The as-synthesized barium sulphate nanostructures were subjected to different characterization techniques for their structural, functional, morphological and elemental studies by using XRD, FTIR, SEM and EDX. XRD reveals the orthorhombic crystal phase with a sharp diffraction peaks phase. SEM studies revealed the rice grain-like structures with an average diameter of 71.36 nm. Furthermore, a better understanding of this biological phenomenon may provide new insights for enhancing nanomaterial usage in the future.
- 29 March 2024
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 13 (1) , 92-96
Open AccessGreen Synthesis of Barium Sulphate Nanostructures Using Azadirachta indica Leaf Extract
Green synthesis of nanostructures is a growing technology owing to its potential applications in various fields. The method is feasible, simple and non-toxic; it is a low-cost strategy. It meets the standards of green chemistry, high crystalline nature and morphological structures. In this work, green synthesis of barium sulphate nanostructure was carried out by using Azadirachta indica (neem) leaf extract, barium chloride dehydrates and anhydrous sodium sulphate as source materials, by co-precipitation method. The as-synthesized barium sulphate nanostructures were subjected to different characterization techniques for their structural, functional, morphological and elemental studies by using XRD, FTIR, SEM and EDX. XRD reveals the orthorhombic crystal phase with a sharp diffraction peaks phase. SEM studies revealed the rice grain-like structures with an average diameter of 71.36 nm. Furthermore, a better understanding of this biological phenomenon may provide new insights for enhancing nanomaterial usage in the future.
- Open Access
- 1 January 2024
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 13 (4) , 20-26
Morphological Controlled BaSO4 Nanostructures by Solvents and Molar Concentrations
The aim of the present work is to synthesize environmentally friendly nanomaterials, which are viable and better alternative method for distinct applications. The co-precipitation method is used for the preparation of BaSO4 nanostructures with the influence of Azedarach indica leaf extracts as organic stabilizing agents. For synthesizing nanostructures, two different solvents (Ethanol and deionized water) were taken along with distinct molar concentration (0.05 and 1.0 M) are investigated by various characterization techniques. Initially, the XRD pattern revealing the orthorhombic phase structure was well-matched with JCPDS file. Next, FTIR transmission spectrum confirmed the presence of Ba and SO4 stretching vibration molecules. The morphological studies of SEM evidenced at 1 and 2 µm scale level the successful preparation of rice grain (or nanorods) like nanostructures with the average diameter of ~73.5 nm (ethanol) and 222 nm (DI water). Also, the prepared sample elements were evidenced by the EDX spectra. This employed experimental study revealed that the DI water solvent with higher molar concentrations plays a crucial role in the morphology and size of BaSO4 nanostructures. In the future, these nanocrystalline materials could be find applications in antimicrobial activities.
- 1 January 2024
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 13 (4) , 20-26
Open AccessMorphological Controlled BaSO4 Nanostructures by Solvents and Molar Concentrations
The aim of the present work is to synthesize environmentally friendly nanomaterials, which are viable and better alternative method for distinct applications. The co-precipitation method is used for the preparation of BaSO4 nanostructures with the influence of Azedarach indica leaf extracts as organic stabilizing agents. For synthesizing nanostructures, two different solvents (Ethanol and deionized water) were taken along with distinct molar concentration (0.05 and 1.0 M) are investigated by various characterization techniques. Initially, the XRD pattern revealing the orthorhombic phase structure was well-matched with JCPDS file. Next, FTIR transmission spectrum confirmed the presence of Ba and SO4 stretching vibration molecules. The morphological studies of SEM evidenced at 1 and 2 µm scale level the successful preparation of rice grain (or nanorods) like nanostructures with the average diameter of ~73.5 nm (ethanol) and 222 nm (DI water). Also, the prepared sample elements were evidenced by the EDX spectra. This employed experimental study revealed that the DI water solvent with higher molar concentrations plays a crucial role in the morphology and size of BaSO4 nanostructures. In the future, these nanocrystalline materials could be find applications in antimicrobial activities.
- Open Access
- 1 January 2024
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 13 (4) , 108-113
Front Nanogratings Decorated Ultrathin Film Amorphous Si Solar Cell Performances
Solar cells provide a renewable, clean energy source, reducing reliance on fossil fuels and minimizing environmental impact. They offer economic savings, energy independence, and flexibility for various applications. In this work, the nanophotonic and nanoplasmonic grating structures are integrated in the front side of the active (amorphous Si) layer. The transverse electric and transverse magnetic field distributions were demonstrated by varying the incident wavelengths at a normal incidence angle. Furthermore, improved current densities of distinct ultrathin amorphous Si (a-Si) solar cells decorated with nanogratings (SiO2, Ag, and Si3N4) were explored. The obtained results indicated that the optimized SiO2 nanogratings and Si3N4 film acted as anti-reflection coating (ARC) layers with air medium (AM 1.5) and showed a remarkable current density of 16.25 mA/cm2 in ultrathin a-Si solar cells with a thickness of 180 nm.
- 1 January 2024
- Published by Journal of Environmental Nanotechnology in Journal of Environmental Nanotechnology
- Vol. 13 (4) , 108-113
Open AccessFront Nanogratings Decorated Ultrathin Film Amorphous Si Solar Cell Performances
Solar cells provide a renewable, clean energy source, reducing reliance on fossil fuels and minimizing environmental impact. They offer economic savings, energy independence, and flexibility for various applications. In this work, the nanophotonic and nanoplasmonic grating structures are integrated in the front side of the active (amorphous Si) layer. The transverse electric and transverse magnetic field distributions were demonstrated by varying the incident wavelengths at a normal incidence angle. Furthermore, improved current densities of distinct ultrathin amorphous Si (a-Si) solar cells decorated with nanogratings (SiO2, Ag, and Si3N4) were explored. The obtained results indicated that the optimized SiO2 nanogratings and Si3N4 film acted as anti-reflection coating (ARC) layers with air medium (AM 1.5) and showed a remarkable current density of 16.25 mA/cm2 in ultrathin a-Si solar cells with a thickness of 180 nm.
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3170 (1) , 040012
Preparation and study of sol-gel solution of spin coated transparent single-TiO2 and SiO2 thin film for opto-electronic applications
In this work, the sol-gel synthesis and spin-coating deposition process is a simple technique used to fabricate dielectric thin films using tetraethyl orthosili In this work, the sol-gel synthesis and spin-coating deposition process is a simple technique used to fabricate dielectric thin films using tetraethyl orthosili
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3170 (1) , 040012
Preparation and study of sol-gel solution of spin coated transparent single-TiO2 and SiO2 thin film for opto-electronic applications
In this work, the sol-gel synthesis and spin-coating deposition process is a simple technique used to fabricate dielectric thin films using tetraethyl orthosili In this work, the sol-gel synthesis and spin-coating deposition process is a simple technique used to fabricate dielectric thin films using tetraethyl orthosili
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3170 (1) , 030007
Sol-gel synthesis and optical characterization of zinc doped TiO2 nanoparticles
In this work, zinc-doped titanium di-oxide (Zn-TiO2) nanoparticles were prepared by using sol-gel method. The optical and surface morphological studies were inv In this work, zinc-doped titanium di-oxide (Zn-TiO2) nanoparticles were prepared by using sol-gel method. The optical and surface morphological studies were inv
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3170 (1) , 030007
Sol-gel synthesis and optical characterization of zinc doped TiO2 nanoparticles
In this work, zinc-doped titanium di-oxide (Zn-TiO2) nanoparticles were prepared by using sol-gel method. The optical and surface morphological studies were inv In this work, zinc-doped titanium di-oxide (Zn-TiO2) nanoparticles were prepared by using sol-gel method. The optical and surface morphological studies were inv