Kai Jing
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kai Jing has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
Yiqi Zhuang
School of Microelectronics, Xidian University, Xian, China
6 shared publicationsNingmei Yu
School of Automation and Information Engineering, Xi'an University of Technology, Xi'an, Shaanxi, China
3 shared publicationsXing Quan
Xi Dian Univ, Sch Mechano Elect Engn, Xian, Shaanxi, Peoples R China
3 shared publicationsYanlong Zhang
School of Microelectronics, Xidian University, Xi’an, 71071,P.R. China
3 shared publicationsZhenrong Li
School of Microelectronics, Xidian University, Xi’an, 71071,P.R. China
3 shared publications- Ningmei Yu
Xi’an University of Technology
2 shared publications
Latest Publications
- 24 October 2026
- Published by Elsevier in Microelectronics Journal
- Vol. 179
A chopper-stabilized operational amplifier with a high-accuracy current-sensing class-AB biasing circuit
- 24 October 2026
- Published by Elsevier in Microelectronics Journal
- Vol. 179
A chopper-stabilized operational amplifier with a high-accuracy current-sensing class-AB biasing circuit
- 29 October 2025
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 45 (5) , 3348-3368
A High FOM Current Reference Circuit Utilizes a Novel Temperature Stabilization Method
- 29 October 2025
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 45 (5) , 3348-3368
A High FOM Current Reference Circuit Utilizes a Novel Temperature Stabilization Method
- 11 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (12) , 1827-1831
A 2.56ppm/°C High-Order Curvature-Compensated Bandgap Reference Utilizing Four-Input Current Feedback Amplifier
This paper presents a high-order curvature-compensated bandgap reference (BGR) that utilizes a four-input current feedback amplifier. High-order curvature compensation terms (T∙ ln(T) dependence) are produced by the VEB’s difference of bipolar transistors (BJT) whose currents are biased at proportional to absolute temperature (PTAT) and complementary to absolute temperature (CTAT) currents, which can diminish the temperature-dependent nonlinearity of traditional BGR. A four-input current feedback summation amplifier innovatively incorporates an additional input pair to complete the summation of the first-order and high-order curvature compensation terms. In conjunction with an auto-zero technique built on a new timing constraint, the proposed BGR enhances the accuracy as well as suppresses the low-frequency noise. Implemented in a standard 180-nm CMOS process, this work exhibits a minimum temperature coefficient (TC) of 2.56 ppm/∘C and an average TC of 3.5 ppm/∘C, with a worst-case scenario of 5.08 ppm/∘C from -40∘C to 125∘C, requiring a mere one-point, 4-bit trimming. Measurement results indicate an initial 3σ inaccuracy of ±0.14% without trimming, which is reduced to ±0.05% with trimming. The low-frequency noise (0.01Hz to 10Hz) is 6.8 μVRMS.
- 11 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (12) , 1827-1831
A 2.56ppm/°C High-Order Curvature-Compensated Bandgap Reference Utilizing Four-Input Current Feedback Amplifier
This paper presents a high-order curvature-compensated bandgap reference (BGR) that utilizes a four-input current feedback amplifier. High-order curvature compensation terms (T∙ ln(T) dependence) are produced by the VEB’s difference of bipolar transistors (BJT) whose currents are biased at proportional to absolute temperature (PTAT) and complementary to absolute temperature (CTAT) currents, which can diminish the temperature-dependent nonlinearity of traditional BGR. A four-input current feedback summation amplifier innovatively incorporates an additional input pair to complete the summation of the first-order and high-order curvature compensation terms. In conjunction with an auto-zero technique built on a new timing constraint, the proposed BGR enhances the accuracy as well as suppresses the low-frequency noise. Implemented in a standard 180-nm CMOS process, this work exhibits a minimum temperature coefficient (TC) of 2.56 ppm/∘C and an average TC of 3.5 ppm/∘C, with a worst-case scenario of 5.08 ppm/∘C from -40∘C to 125∘C, requiring a mere one-point, 4-bit trimming. Measurement results indicate an initial 3σ inaccuracy of ±0.14% without trimming, which is reduced to ±0.05% with trimming. The low-frequency noise (0.01Hz to 10Hz) is 6.8 μVRMS.
- Open Access
A Piezoresistive-Sensor Nonlinearity Correction on-Chip Method with Highly Robust Class-AB Driving Capability
This paper presents a thorough robust Class-AB power amplifier design and its application in pressure-mode sensor-on-chip nonlinearity correction. Considering its use in piezoresistive sensing applications, a gain-boosting-aided folded cascode structure is utilized to increase the amplifier’s gain by a large amount as well as enhancing the power rejection ability, and a push–pull structure with miller compensation, a floating gate technique, and an adaptive output driving limiting structures are adopted to achieve high-efficiency current driving capability, high stability, and electronic environmental compatibility. This amplifier is applied in a real sensor nonlinearity correction on-chip system. With the help of a self-designed 7-bit + sign DAC and a self-designed two-stage operational amplifier, this system is compatible with nonlinear correction at different signal conditioning output values. It can also drive resistive sensors as small as 300 ohms and as high as tens of thousands of ohms. The designed two-stage operational amplifier utilizes the TSMC 0.18 um process, resulting in a final circuit power consumption of 0.183 mW. The amplifier exhibits a gain greater than 140 dB, a phase margin of 68°, and a unit gain bandwidth exceeding 199.76 kHz. The output voltage range spans from 0 to 4.6 V. The final simulation results indicate that the nonlinear correction system designed in this paper can correct piezoresistive sensors with a nonlinearity of up to ±2.5% under various PVT (Process–Voltage–Temperature) conditions. After calibration by this system, the maximum error in the output voltage is 4 mV, effectively reducing the nonlinearity to 4% of its original value in the worst-case scenario.
Open AccessA Piezoresistive-Sensor Nonlinearity Correction on-Chip Method with Highly Robust Class-AB Driving Capability
This paper presents a thorough robust Class-AB power amplifier design and its application in pressure-mode sensor-on-chip nonlinearity correction. Considering its use in piezoresistive sensing applications, a gain-boosting-aided folded cascode structure is utilized to increase the amplifier’s gain by a large amount as well as enhancing the power rejection ability, and a push–pull structure with miller compensation, a floating gate technique, and an adaptive output driving limiting structures are adopted to achieve high-efficiency current driving capability, high stability, and electronic environmental compatibility. This amplifier is applied in a real sensor nonlinearity correction on-chip system. With the help of a self-designed 7-bit + sign DAC and a self-designed two-stage operational amplifier, this system is compatible with nonlinear correction at different signal conditioning output values. It can also drive resistive sensors as small as 300 ohms and as high as tens of thousands of ohms. The designed two-stage operational amplifier utilizes the TSMC 0.18 um process, resulting in a final circuit power consumption of 0.183 mW. The amplifier exhibits a gain greater than 140 dB, a phase margin of 68°, and a unit gain bandwidth exceeding 199.76 kHz. The output voltage range spans from 0 to 4.6 V. The final simulation results indicate that the nonlinear correction system designed in this paper can correct piezoresistive sensors with a nonlinearity of up to ±2.5% under various PVT (Process–Voltage–Temperature) conditions. After calibration by this system, the maximum error in the output voltage is 4 mV, effectively reducing the nonlinearity to 4% of its original value in the worst-case scenario.
- Open Access
- 17 June 2021
- Published by Elsevier in Microelectronics Journal
- Vol. 114, 105142
Design of 0–15 GHz flat-bandwidth programmable gain amplifier based on transconductance switching technique
- 17 June 2021
- Published by Elsevier in Microelectronics Journal
- Vol. 114, 105142
Open AccessDesign of 0–15 GHz flat-bandwidth programmable gain amplifier based on transconductance switching technique
- 1 July 2020
- Published by Elsevier in Microelectronics Journal
- Vol. 101
Dynamic equalization and fast settling based wide operating voltage range 93 dB PSRR PTAT current reference
- 1 July 2020
- Published by Elsevier in Microelectronics Journal
- Vol. 101
Dynamic equalization and fast settling based wide operating voltage range 93 dB PSRR PTAT current reference
- 26 February 2020
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 39 (9) , 4499-4515
Methodology of Noise Flatness Based on Network Quality Factor in RF Wideband Applications
- 26 February 2020
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 39 (9) , 4499-4515
Methodology of Noise Flatness Based on Network Quality Factor in RF Wideband Applications
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2228-2231
A 168 dB high gain folded cascode operational amplifier for Delta-Sigma ADC
A fully differential CMOS folded cascode operational amplifier is presented. It uses gain boosting technique on both NMOS and PMOS branch to enhance total gain. New current-sink topology is used to maximally enhance the open-loop gain as well as not to deteriorate the output swing badly. Local small area but good-performance CT-CMFB is adopted in gain-boosted auxiliary amplifier to optimize both area cost and calibration performance. An improved SC-CMFB is used on total amplifier output to stabilize the output common mode node voltage as well as not to impact differential gain performance. Designed in low-cost UMC 110 nm process with a 5V supply voltage, simulation results show DC gain of 164.1 dB and a phase margin of 63 degree at a unity gain bandwidth of 17.09 MHz. The static current is 174 uA along with achieved PSRR of 186.5dB, making it suitable in high-performance Delta-Sigma ADCs.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2228-2231
A 168 dB high gain folded cascode operational amplifier for Delta-Sigma ADC
A fully differential CMOS folded cascode operational amplifier is presented. It uses gain boosting technique on both NMOS and PMOS branch to enhance total gain. New current-sink topology is used to maximally enhance the open-loop gain as well as not to deteriorate the output swing badly. Local small area but good-performance CT-CMFB is adopted in gain-boosted auxiliary amplifier to optimize both area cost and calibration performance. An improved SC-CMFB is used on total amplifier output to stabilize the output common mode node voltage as well as not to impact differential gain performance. Designed in low-cost UMC 110 nm process with a 5V supply voltage, simulation results show DC gain of 164.1 dB and a phase margin of 63 degree at a unity gain bandwidth of 17.09 MHz. The static current is 174 uA along with achieved PSRR of 186.5dB, making it suitable in high-performance Delta-Sigma ADCs.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Offset-free Column Buffer for CMOS image sensor
A new column buffer circuit with improved offset mismatch and charge sharing for CMOS image sensor is proposed in this paper. Based on the bottom plate sampling and fixed common level method, this novel design can avoid the offset non-uniformity of the two buffers. Also, it can restrain the charge sharing caused by the varied operating point by using a single buffer and switched capacitor technique. The proposed techniques are experimentally verified in a 1024 × 1024 prototype chip using 55nm low power CMOS process. The simulation results show that the linear range is extended by 20%, and the improved photo response non-uniformity is up to 1.16%.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Offset-free Column Buffer for CMOS image sensor
A new column buffer circuit with improved offset mismatch and charge sharing for CMOS image sensor is proposed in this paper. Based on the bottom plate sampling and fixed common level method, this novel design can avoid the offset non-uniformity of the two buffers. Also, it can restrain the charge sharing caused by the varied operating point by using a single buffer and switched capacitor technique. The proposed techniques are experimentally verified in a 1024 × 1024 prototype chip using 55nm low power CMOS process. The simulation results show that the linear range is extended by 20%, and the improved photo response non-uniformity is up to 1.16%.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
A Reconfigurable Low Noise Amplifier with Sub-amplifier Compensation for Wearable Wireless Neural Recording System
A reconfigurable low noise amplifier with sub-amplifier cascode miller compensation is proposed to obtain stability both in action potential (AP) and local field potential (LFP) applications. The phase margin of more than 60 degrees can be guaranteed in both two modes compared with traditional method. Simulations have been performed in standard 0.18μm technology parameters and the simulated characteristics of the proposed amplifier show that the input referred noise and the power consumption is 3.44/6.88μVrms and 2.48/5.46μW in both AP and LFP bands.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
A Reconfigurable Low Noise Amplifier with Sub-amplifier Compensation for Wearable Wireless Neural Recording System
A reconfigurable low noise amplifier with sub-amplifier cascode miller compensation is proposed to obtain stability both in action potential (AP) and local field potential (LFP) applications. The phase margin of more than 60 degrees can be guaranteed in both two modes compared with traditional method. Simulations have been performed in standard 0.18μm technology parameters and the simulated characteristics of the proposed amplifier show that the input referred noise and the power consumption is 3.44/6.88μVrms and 2.48/5.46μW in both AP and LFP bands.