Jürgen Maas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jürgen Maas has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Robert Courant
Mechatronic Systems Lab, Technische Universität Berlin, Hardenbergstraße 36, 10623 Berlin, Germany
5 shared publications - Abd Elkarim Masoud
Mechatronic Systems Lab, technical university of berlin, Berlin, Germany
2 shared publications - Andreas Hubracht
Technische Universität Berlin, Mechatronic Systems Lab, Hardenbergstraße 36, 10623 Berlin, Germany
2 shared publications Christian Graf
Control Engineering and Mechatronic Systems, Ostwestfalen-Lippe University of Applied Sciences, Lemgo, Germany
2 shared publicationsDirk Güth
Ostwestfalen-Lippe University of Applied Sciences, Control Engineering and Mechatronic Systems, Lemgo, Germany
2 shared publications- Jana Mertens
Technische Universität Berlin, Mechatronic Systems Lab, Hardenbergstraße 36, 10623 Berlin, Germany
2 shared publications
Latest Publications
- Open Access
- 25 September 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (10) , 1083
Magnetorheological Fluid Utilized for Online Rotor Balancing
Unbalance in rotating machinery causes significant vibrations, reducing lifespan and efficiency. This study overcomes the limitations of conventional offline balancing by introducing an online rotor balancing system utilizing Magnetorheological Fluid (MRF). The system employs three chambers containing MRF and balancing spheres. A hybrid magnetic system is designed, combining permanent magnets for fixing in the balanced state and a stationary electromagnet for contactless control of the sphere position during balancing. A control algorithm was developed based on multiphysics modeling and experimental parameterization. Experimental validation demonstrated the high effectiveness of reducing initial rotor unbalance, thereby confirming the feasibility of the proposed concept. The hybrid magnetic design provides inherent multistability and energy efficiency, making it a promising and effective solution for active vibration reduction in rotating machinery.
- 25 September 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (10) , 1083
Open AccessMagnetorheological Fluid Utilized for Online Rotor Balancing
Unbalance in rotating machinery causes significant vibrations, reducing lifespan and efficiency. This study overcomes the limitations of conventional offline balancing by introducing an online rotor balancing system utilizing Magnetorheological Fluid (MRF). The system employs three chambers containing MRF and balancing spheres. A hybrid magnetic system is designed, combining permanent magnets for fixing in the balanced state and a stationary electromagnet for contactless control of the sphere position during balancing. A control algorithm was developed based on multiphysics modeling and experimental parameterization. Experimental validation demonstrated the high effectiveness of reducing initial rotor unbalance, thereby confirming the feasibility of the proposed concept. The hybrid magnetic design provides inherent multistability and energy efficiency, making it a promising and effective solution for active vibration reduction in rotating machinery.
- Open Access
- 1 September 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (9) , 095029
Bistable dielectric elastomer generator with reduced and adjustable stiffness characteristics
This paper presents a novel energy harvesting system based on a dielectric elastomer generator (DEG) integrated with nonlinear mechanical elements to enable bistable operation and enhance energy conversion. A comprehensive dynamic model is developed using an energy-based approach to consistently describe the coupled electromechanical behavior of the system. The proposed DEG concept is characterized by equibiaxial deformation and tailored stiffness, allowing efficient energy harvesting at reduced actuation effort. Experimental results validate the model and demonstrate that the combination of nonlinearities and bistability significantly improves performance. The system is suitable for broadband ambient excitations and offers a promising approach toward more effective soft energy harvesters.
- 1 September 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (9) , 095029
Open AccessBistable dielectric elastomer generator with reduced and adjustable stiffness characteristics
This paper presents a novel energy harvesting system based on a dielectric elastomer generator (DEG) integrated with nonlinear mechanical elements to enable bistable operation and enhance energy conversion. A comprehensive dynamic model is developed using an energy-based approach to consistently describe the coupled electromechanical behavior of the system. The proposed DEG concept is characterized by equibiaxial deformation and tailored stiffness, allowing efficient energy harvesting at reduced actuation effort. Experimental results validate the model and demonstrate that the combination of nonlinearities and bistability significantly improves performance. The system is suitable for broadband ambient excitations and offers a promising approach toward more effective soft energy harvesters.
- Open Access
- 1 July 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (7) , 075033
Printing and electromechanical evaluation of stretchable electrodes for dielectric elastomer transducers
Fabrication of electrode layers is a critical process for the production and performance of dielectric elastomer transducers (DETs). This paper focuses on the precise and reliable printing of various electrodes and the electromechanical evaluation of the printed layers. Printing technology offers numerous advantages for creating thin, compliant electrode layers; however, the lack of a standard electrode ink poses challenges for the research and development of the entire fabrication process. In this study, four electrode materials based on carbon black and one based on carbon nanotubes were specially adapted and printed using a contactless jetting system. A characterization setup is realized to facilitate measurements. Multilayer DET samples with different electrode layers, utilizing both 50 µm and 20 µm elastomer films, are manufactured and subjected to electromechanical measurements. This study provides a detailed investigation of the electrode influence on the electromechanical properties of the DET, including capacitance, resistance, stiffening and electrical actuation performance. Finally, the results are evaluated to assess electrode effects and DET’s performance. The measurements indicate that the electrodes influence the stiffening, capacitance, and actuation performance of the DET to varying degrees.
- 1 July 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (7) , 075033
Open AccessPrinting and electromechanical evaluation of stretchable electrodes for dielectric elastomer transducers
Fabrication of electrode layers is a critical process for the production and performance of dielectric elastomer transducers (DETs). This paper focuses on the precise and reliable printing of various electrodes and the electromechanical evaluation of the printed layers. Printing technology offers numerous advantages for creating thin, compliant electrode layers; however, the lack of a standard electrode ink poses challenges for the research and development of the entire fabrication process. In this study, four electrode materials based on carbon black and one based on carbon nanotubes were specially adapted and printed using a contactless jetting system. A characterization setup is realized to facilitate measurements. Multilayer DET samples with different electrode layers, utilizing both 50 µm and 20 µm elastomer films, are manufactured and subjected to electromechanical measurements. This study provides a detailed investigation of the electrode influence on the electromechanical properties of the DET, including capacitance, resistance, stiffening and electrical actuation performance. Finally, the results are evaluated to assess electrode effects and DET’s performance. The measurements indicate that the electrodes influence the stiffening, capacitance, and actuation performance of the DET to varying degrees.
- Open Access
- 30 November 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (8)
Modeling and Accessing Smart Materials with Integrity Constraints in the Shapes Constraint Language and Ontologies—The SmaDi Way
Various types of semantic artifacts play a vital role in developing software systems, for example, information systems for materials scientists that adhere to the findability, accessibility, interoperability, reusability principles for digital assets. Among them, integrity constraints (ICs) are essential artifacts as they orthogonally add to the representation capabilities of ontologies a means to enforce consistency and completeness of given data. An IC language recommended by the worldwide web consortium (W3C) for use with linked open data is Shapes Constraint Language (SHACL). This article discusses the algorithm and evaluation results for a new SHACL validator developed in the context of SmaDi, a project for digitalizing smart materials associated with MaterialDigital. The new validator reduces SHACL constraints to SPARQL Protocol and RDF Query Language (SPARQL) queries, that is, queries in the W3C recommended query language over repositories represented in the standard syntax for linked open data, RDF. Hence, in contrast to off‐the‐shelf validators, it can be used with any SPARQL endpoint, even if there is only a (virtual) view of the RDF data. The article demonstrates the use of SHACL ICs for modeling some simple constraints over smart materials. The evaluation shows that our SHACL validator has processing times comparable to off‐the‐shelf SHACL validators.
- 30 November 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (8)
Open AccessModeling and Accessing Smart Materials with Integrity Constraints in the Shapes Constraint Language and Ontologies—The SmaDi Way
Various types of semantic artifacts play a vital role in developing software systems, for example, information systems for materials scientists that adhere to the findability, accessibility, interoperability, reusability principles for digital assets. Among them, integrity constraints (ICs) are essential artifacts as they orthogonally add to the representation capabilities of ontologies a means to enforce consistency and completeness of given data. An IC language recommended by the worldwide web consortium (W3C) for use with linked open data is Shapes Constraint Language (SHACL). This article discusses the algorithm and evaluation results for a new SHACL validator developed in the context of SmaDi, a project for digitalizing smart materials associated with MaterialDigital. The new validator reduces SHACL constraints to SPARQL Protocol and RDF Query Language (SPARQL) queries, that is, queries in the W3C recommended query language over repositories represented in the standard syntax for linked open data, RDF. Hence, in contrast to off‐the‐shelf validators, it can be used with any SPARQL endpoint, even if there is only a (virtual) view of the RDF data. The article demonstrates the use of SHACL ICs for modeling some simple constraints over smart materials. The evaluation shows that our SHACL validator has processing times comparable to off‐the‐shelf SHACL validators.
- Open Access
- 29 August 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (9) , 095041
Modeling and experimental investigation of multilayer DE transducers considering the influence of the electrode layers
A current research topic for dielectric elastomer (DE) materials is the reduction of the thickness of the DE layer in order to achieve a lower operating voltage with the same electric field strength. As the ratio of the layer thicknesses of the electrode to the elastomer is therefore more important, the mechanical properties of the electrode layers are of greater significance. Several research articles deal with investigations, exploring the influence of electrode materials on the behavior of the DE transducer and emphasizing its importance. In analytical models, however, the electrodes are not usually considered separately, but the parameters are identified for the entire DE composite, consisting of elastomer and electrode layers. In contrast, in this article the material characterization is carried out separately for the two materials in a first step. In a further step, a holistic model for multilayer DE transducers is derived on the basis of this material-specific characterization and subsequently validated with measurements. For the DE layers, ELASTOSIL ® 2030 (EL 2030), and for the electrode layers, ELASTOSIL ® LR 3162 (EL 3162) are investigated, frequently used materials for DE transducers that offer reproducible properties for the investigation. EL 3162 is a carbon black filled elastomer material that exhibits higher elastic and viscose stresses as well as a significant rate-independent hysteresis compared to EL 2030. Experimental investigations of DE transducers with different electrode thicknesses are examined to validate the model and to demonstrate the significance and influence of the electrode layers on the transducer’s performance. Furthermore, the influence of the electrode properties on the actuator, generator and sensor behavior of the DE transducer is analyzed based on the developed model. Depending on the thickness and number of layers, this underlines the relevance of the electrode properties and provides information on the optimized design of the DE transducer.
- 29 August 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (9) , 095041
Open AccessModeling and experimental investigation of multilayer DE transducers considering the influence of the electrode layers
A current research topic for dielectric elastomer (DE) materials is the reduction of the thickness of the DE layer in order to achieve a lower operating voltage with the same electric field strength. As the ratio of the layer thicknesses of the electrode to the elastomer is therefore more important, the mechanical properties of the electrode layers are of greater significance. Several research articles deal with investigations, exploring the influence of electrode materials on the behavior of the DE transducer and emphasizing its importance. In analytical models, however, the electrodes are not usually considered separately, but the parameters are identified for the entire DE composite, consisting of elastomer and electrode layers. In contrast, in this article the material characterization is carried out separately for the two materials in a first step. In a further step, a holistic model for multilayer DE transducers is derived on the basis of this material-specific characterization and subsequently validated with measurements. For the DE layers, ELASTOSIL ® 2030 (EL 2030), and for the electrode layers, ELASTOSIL ® LR 3162 (EL 3162) are investigated, frequently used materials for DE transducers that offer reproducible properties for the investigation. EL 3162 is a carbon black filled elastomer material that exhibits higher elastic and viscose stresses as well as a significant rate-independent hysteresis compared to EL 2030. Experimental investigations of DE transducers with different electrode thicknesses are examined to validate the model and to demonstrate the significance and influence of the electrode layers on the transducer’s performance. Furthermore, the influence of the electrode properties on the actuator, generator and sensor behavior of the DE transducer is analyzed based on the developed model. Depending on the thickness and number of layers, this underlines the relevance of the electrode properties and provides information on the optimized design of the DE transducer.
- Open Access
- 7 August 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (9) , 095014
A novel scale-bridging method for MSMA linking continuum thermodynamics constitutive formulations to lumped system-level models
This work introduces a novel scale-bridging method between a continuum thermodynamics constitutive model and a lumped system-level model for magnetic shape memory alloys (MSMA). With this method, system models for real-time operations are generated based on virtual experiments using the constitutive model. The proposed method addresses the fact that, while constitutive models for MSMA typically only require small sets of parameters as input, their evaluation is still computationally expensive. System models for control engineering, however, require extensive experimental parameterization, while their evaluation is highly time-efficient. The proposed scale-bridging method has the potential to combine a small parameterization effort and a low computational cost of the real-time system model. Additionally, the constitutive model is utilized to investigate whether it can determine the individual behavior of MSMA samples. This is important since the inherent model parameters, while valid for ideal single crystals, deviate for non-ideal MSMA sample behavior. To this end, the MSMA constitutive model, based on a global variational principle originally proposed by Kiefer et al is supplemented by various extensions, including a more robust algorithmic treatment. A parameter identification procedure is introduced to optimize the constitutive model parameters based on an outer hysteresis curve for a particular load case. By conducting virtual experiments with the constitutive model, data sets are generated to parameterize Preisach hysteresis models as numerical approximations of the constitutive models. The resulting hysteresis models are compared with physical experiments using an MSMA test bench for different load cases. It is shown that the proposed scale-bridging method successfully generates hysteresis models derived from constitutive models. While maintaining accuracy comparable to strictly phenomenological models across various load cases (as validated through physical MSMA test bench experiments), these models require significantly less parameterization effort than classical system models. This translates to faster model creation and broader applicability.
- 7 August 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (9) , 095014
Open AccessA novel scale-bridging method for MSMA linking continuum thermodynamics constitutive formulations to lumped system-level models
This work introduces a novel scale-bridging method between a continuum thermodynamics constitutive model and a lumped system-level model for magnetic shape memory alloys (MSMA). With this method, system models for real-time operations are generated based on virtual experiments using the constitutive model. The proposed method addresses the fact that, while constitutive models for MSMA typically only require small sets of parameters as input, their evaluation is still computationally expensive. System models for control engineering, however, require extensive experimental parameterization, while their evaluation is highly time-efficient. The proposed scale-bridging method has the potential to combine a small parameterization effort and a low computational cost of the real-time system model. Additionally, the constitutive model is utilized to investigate whether it can determine the individual behavior of MSMA samples. This is important since the inherent model parameters, while valid for ideal single crystals, deviate for non-ideal MSMA sample behavior. To this end, the MSMA constitutive model, based on a global variational principle originally proposed by Kiefer et al is supplemented by various extensions, including a more robust algorithmic treatment. A parameter identification procedure is introduced to optimize the constitutive model parameters based on an outer hysteresis curve for a particular load case. By conducting virtual experiments with the constitutive model, data sets are generated to parameterize Preisach hysteresis models as numerical approximations of the constitutive models. The resulting hysteresis models are compared with physical experiments using an MSMA test bench for different load cases. It is shown that the proposed scale-bridging method successfully generates hysteresis models derived from constitutive models. While maintaining accuracy comparable to strictly phenomenological models across various load cases (as validated through physical MSMA test bench experiments), these models require significantly less parameterization effort than classical system models. This translates to faster model creation and broader applicability.
- Open Access
- 1 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 107855-107871
Design and Characterization of an Efficient Multistable Push-Pull Linear Actuator Using Magnetic Shape Memory Alloys
Magnetic shape memory alloys (MSMA) exhibit promising potential for industrial applications, particularly fast-switching linear actuators. Alongside the eponymous active magnetic shape memory effect, they are characterized by a significant hysteresis owing to the material-inherent twinning stresses. In conventional MSMA push-actuators, twinning stresses represent an energy loss. However, energy efficient concepts embrace them as a multistable holding force, which is especially beneficial for applications like robotic grippers, clamping devices and valves. To actively use the MSM effect in both push- and pull-direction, perpendicular magnetic fields are required. In this paper, we present a novel excitation setup using highly anisotropic pole shoes that can provide the necessary fields with unprecedented efficiency. The concept can be customized to provide an inherent bias force in an arbitrary direction tailored to a specific use case. A demonstrator based on our approach is realized for a balanced push-pull actuator and analyzed extensively both simulatively as well as experimentally. For the simulations using COMSOL Multiphysics we combined non-linear magnetics and mechanics with a model using homogenized twin bands from previous work. The non-linear switching patterns predicted in the simulation are optically investigated on a physical demonstrator using digital image correlation. All results verify the dynamic and efficient multistable performance even against small disturbances.
- 1 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 107855-107871
Open AccessDesign and Characterization of an Efficient Multistable Push-Pull Linear Actuator Using Magnetic Shape Memory Alloys
Magnetic shape memory alloys (MSMA) exhibit promising potential for industrial applications, particularly fast-switching linear actuators. Alongside the eponymous active magnetic shape memory effect, they are characterized by a significant hysteresis owing to the material-inherent twinning stresses. In conventional MSMA push-actuators, twinning stresses represent an energy loss. However, energy efficient concepts embrace them as a multistable holding force, which is especially beneficial for applications like robotic grippers, clamping devices and valves. To actively use the MSM effect in both push- and pull-direction, perpendicular magnetic fields are required. In this paper, we present a novel excitation setup using highly anisotropic pole shoes that can provide the necessary fields with unprecedented efficiency. The concept can be customized to provide an inherent bias force in an arbitrary direction tailored to a specific use case. A demonstrator based on our approach is realized for a balanced push-pull actuator and analyzed extensively both simulatively as well as experimentally. For the simulations using COMSOL Multiphysics we combined non-linear magnetics and mechanics with a model using homogenized twin bands from previous work. The non-linear switching patterns predicted in the simulation are optically investigated on a physical demonstrator using digital image correlation. All results verify the dynamic and efficient multistable performance even against small disturbances.
- Open Access
- 31 May 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (8)
A Novel Digitalization Approach for Smart Materials – Ontology‐Based Access to Data and Models
Smart materials react to physical fields (e.g., electric, magnetic, and thermal fields) and can be used as sensors, actuators, and generators due to their bidirectional behavior. Easy and multiscale access to material data and models enables efficient research and development with regard to the selection of appropriate materials and their optimization towards specific applications. However, different working principles, measurement and analysis methods, as well as data storage approaches lead to heterogeneous and partly inconsistent datasets. The ontology‐based data access (OBDA) is a suitable method to access such heterogeneous datasets easily and quickly, while material models can transform material data across certain scales for different applications. In order to connect both capabilities, an extended approach enabling an ontology‐based data and model access (OBDMA) is presented, also supporting findable, accessible, interoperable, and re‐usable (FAIR). The OBDMA system comprises four main levels, the query, the ontology, the mapping, and the database. Storing knowledge at these different levels increases the interchangeability and enables variable datasets, which is essential, especially for dynamic research fields such as smart materials. In this article, the principles and advantages of the OBDMA approach are demonstrated for different subclasses of smart materials, but can be transferred to other materials, too.
- 31 May 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (8)
Open AccessA Novel Digitalization Approach for Smart Materials – Ontology‐Based Access to Data and Models
Smart materials react to physical fields (e.g., electric, magnetic, and thermal fields) and can be used as sensors, actuators, and generators due to their bidirectional behavior. Easy and multiscale access to material data and models enables efficient research and development with regard to the selection of appropriate materials and their optimization towards specific applications. However, different working principles, measurement and analysis methods, as well as data storage approaches lead to heterogeneous and partly inconsistent datasets. The ontology‐based data access (OBDA) is a suitable method to access such heterogeneous datasets easily and quickly, while material models can transform material data across certain scales for different applications. In order to connect both capabilities, an extended approach enabling an ontology‐based data and model access (OBDMA) is presented, also supporting findable, accessible, interoperable, and re‐usable (FAIR). The OBDMA system comprises four main levels, the query, the ontology, the mapping, and the database. Storing knowledge at these different levels increases the interchangeability and enables variable datasets, which is essential, especially for dynamic research fields such as smart materials. In this article, the principles and advantages of the OBDMA approach are demonstrated for different subclasses of smart materials, but can be transferred to other materials, too.
- Open Access
Design of an Electromagnetic Linear Drive with Permanent Magnetic Weight Compensation
When using electric linear drives for vertical positioning of workloads, a constant force both during movement and at standstill must be supplied to compensate gravity. Compensating stationary forces by the use of passive components reduces the power consumption of the employed actuator and permits smaller dimensioning. In this article, we present a novel integrative actuator design which combines the inherent advantages of a permanent magnetic weight compensation with a two-phase linear direct drive. We illustrate how to design permanent magnetic force compensation to realize a constant compensating force over a desired actuator stroke. Analytical solutions for both the design of the direct drive and the design of the permanent magnetic weight compensation are derived and validated by simulation and experiment. The innovative actuator design is compared to a conventional, non-compensated drive, and we aim to provide the reader with insights into specific applications where the use of the weight-compensated actuator proves particularly effective.
Open AccessDesign of an Electromagnetic Linear Drive with Permanent Magnetic Weight Compensation
When using electric linear drives for vertical positioning of workloads, a constant force both during movement and at standstill must be supplied to compensate gravity. Compensating stationary forces by the use of passive components reduces the power consumption of the employed actuator and permits smaller dimensioning. In this article, we present a novel integrative actuator design which combines the inherent advantages of a permanent magnetic weight compensation with a two-phase linear direct drive. We illustrate how to design permanent magnetic force compensation to realize a constant compensating force over a desired actuator stroke. Analytical solutions for both the design of the direct drive and the design of the permanent magnetic weight compensation are derived and validated by simulation and experiment. The innovative actuator design is compared to a conventional, non-compensated drive, and we aim to provide the reader with insights into specific applications where the use of the weight-compensated actuator proves particularly effective.
- 24 November 2023
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 32 (12) , 125024
Wave field synthesis using buckling dielectric elastomer transducers
This work presents a wave field synthesis (WFS) system using a novel loudspeaker concept based on dielectric elastomers. In WFS, large numbers of densely packed, individual audio channels are controlled to recreate arbitrary acoustic scenarios in the listener space, (i.e. listener zones in a room where different audio content can be radiated in different directions from the array, as seen in the supplemental material). Spatial resolution of the system increases with the increasing number of audio channels and with decreasing loudspeaker spacing. This motivates the use of buckling dielectric elastomer transducers (BDETs) as loudspeakers, which feature a simple setup, rendering them extremely thin and lightweight, and which promises ease of manufacture through the low demand on resources. In this work, a WFS system featuring 480 BDET has been developed. The prototype includes software, electronics, and the loudspeaker array. The electronical and mechanical design of the system is presented in detail. A nonlinear model based on the third-order shear deformation theory is applied to the BDET; the BDET is then experimentally assessed and compared to the model. Further, the final loudspeaker array is characterized by directivity measurements in an anechoic room to validate the reproducibility and quality of the setup. The presented technology highlights the structural advantages of smart materials over conventional transducers, which often are too large, heavy, and expensive for such array applications.
- 24 November 2023
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 32 (12) , 125024
Wave field synthesis using buckling dielectric elastomer transducers
This work presents a wave field synthesis (WFS) system using a novel loudspeaker concept based on dielectric elastomers. In WFS, large numbers of densely packed, individual audio channels are controlled to recreate arbitrary acoustic scenarios in the listener space, (i.e. listener zones in a room where different audio content can be radiated in different directions from the array, as seen in the supplemental material). Spatial resolution of the system increases with the increasing number of audio channels and with decreasing loudspeaker spacing. This motivates the use of buckling dielectric elastomer transducers (BDETs) as loudspeakers, which feature a simple setup, rendering them extremely thin and lightweight, and which promises ease of manufacture through the low demand on resources. In this work, a WFS system featuring 480 BDET has been developed. The prototype includes software, electronics, and the loudspeaker array. The electronical and mechanical design of the system is presented in detail. A nonlinear model based on the third-order shear deformation theory is applied to the BDET; the BDET is then experimentally assessed and compared to the model. Further, the final loudspeaker array is characterized by directivity measurements in an anechoic room to validate the reproducibility and quality of the setup. The presented technology highlights the structural advantages of smart materials over conventional transducers, which often are too large, heavy, and expensive for such array applications.