Ramiro Ruiz-Rosas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ramiro Ruiz-Rosas has a total of 158 co-authors. Here are the top co-authors by number of shared publications:
- Diego Cazorla-Amorós
Materials Institute and Inorganic Chemistry Department, University of Alicante, Ap. 99, E-03080 Alicante, Spain
36 shared publications - Emilia Morallón
Departamento de Química Física and Instituto Universitario de Materiales, Universidad de Alicante, Apartado 99, 03080-Alicante, Spain
34 shared publications - José Rodríguez-Mirasol
Departamento de Ingenierí́a Química, Universidad de Málaga, Andalucia Tech, Campus de Teatinos s/n, 29010 Málaga, Spain
29 shared publications - Tomás Cordero
Departamento de Ingeniería Química, Andalucía Tech, University of Malaga, Campus de Teatinos s/n, 29010 Malaga, Spain
27 shared publications - Juana Maria Rosas
Departamento de Ingenierí́a Química, Universidad de Málaga, Andalucia Tech, Campus de Teatinos s/n, 29010 Málaga, Spain
21 shared publications Tomás Cordero
12 shared publications
Latest Publications
- Open Access
- 22 September 2026
- Published by Elsevier in SSRN Electronic Journal
Synthesis of Polyaniline/Diatomite-MnO2 Composite: Characterization, band gap Evaluation and Photocatalytic Activity
A composite material, polyaniline/diatomite-MnO2 (PANI/DT-MnO2), was successfully synthesized by coating the surface of purified diatomite with manganese oxide using hydrothermal method. This functionalized support was further employed in the preparation of polyaniline/diatomite-MnO2 composite. The produced materials polyaniline (PANI), diatomite-MnO2 (DT-MnO2) and PANI/DT-MnO2 were systematically characterized using Infrared spectroscopy based on the Fourier transform (FTIR), X-ray diffraction (XRD), cyclic voltammetry (CV), thermogravimetric analysis (TGA) and band gap evaluation, indicating successful surface modification and composite formation. The band gap of the synthesized photocatalyst was evaluated with Tauc plot method. The grafting of polyaniline with diatomite-MnO2 increases the band gap of DT-MnO2 from 1.78 eV to 3.09 eV, this can improve charge separation efficiency and decreases electron–hole recombination. Moreover, the composite's photocatalytic activity PANI/DT-MnO2 was investigated using methylene blue dye (MB) as a model organic pollutant under ultraviolet light. The photocatalytic efficacy of the produced composite was assessed using both linear and nonlinear kinetic models. Polyaniline provides abundant active sites and Delocalized π-electron framework, which increase the surface reactivity of PANI/DT-MnO2. It was observed that 93% of the MB solution (100 mL; 30 mg/L) was decomposed within 340 min using 0.1 g of PANI/DT–MnO2 at neutural pH under UV light. The findings reveal the capability of the synthesized composite as an effective photocatalyst for the elimination of organic contaminants in wastewater treatment processes.
- 22 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynthesis of Polyaniline/Diatomite-MnO2 Composite: Characterization, band gap Evaluation and Photocatalytic Activity
A composite material, polyaniline/diatomite-MnO2 (PANI/DT-MnO2), was successfully synthesized by coating the surface of purified diatomite with manganese oxide using hydrothermal method. This functionalized support was further employed in the preparation of polyaniline/diatomite-MnO2 composite. The produced materials polyaniline (PANI), diatomite-MnO2 (DT-MnO2) and PANI/DT-MnO2 were systematically characterized using Infrared spectroscopy based on the Fourier transform (FTIR), X-ray diffraction (XRD), cyclic voltammetry (CV), thermogravimetric analysis (TGA) and band gap evaluation, indicating successful surface modification and composite formation. The band gap of the synthesized photocatalyst was evaluated with Tauc plot method. The grafting of polyaniline with diatomite-MnO2 increases the band gap of DT-MnO2 from 1.78 eV to 3.09 eV, this can improve charge separation efficiency and decreases electron–hole recombination. Moreover, the composite's photocatalytic activity PANI/DT-MnO2 was investigated using methylene blue dye (MB) as a model organic pollutant under ultraviolet light. The photocatalytic efficacy of the produced composite was assessed using both linear and nonlinear kinetic models. Polyaniline provides abundant active sites and Delocalized π-electron framework, which increase the surface reactivity of PANI/DT-MnO2. It was observed that 93% of the MB solution (100 mL; 30 mg/L) was decomposed within 340 min using 0.1 g of PANI/DT–MnO2 at neutural pH under UV light. The findings reveal the capability of the synthesized composite as an effective photocatalyst for the elimination of organic contaminants in wastewater treatment processes.
- Open Access
- 8 September 2026
- Published by Elsevier in SSRN Electronic Journal
SELECTIVE PRODUCTION OF METHANOL BY CO2 HYDROGENATION OVER Cu-ZnO CARBON CATALYSTS DERIVED FROM RESIDUAL BIOMASS
The production of renewable methanol via CO2 hydrogenation was investigated using carbon-based Cu/ZnO catalysts. An activated carbon prepared by physical activation of residual olive stone with CO2 was used as catalyst support. Different Cu/ZnO mass ratios were used to identify the more efficient ZnO loading, fixing the copper content, approximately, at 10 wt.%. Catalysts performance was evaluated at H2/CO2= 3/1, GHSV= 11250 mL·g-1·h-1, 30 bar, and temperatures between 180 and 300 °C. The incorporation of ZnO, even at low loadings, decreased copper particle size and enhanced CO2 chemisorption, leading to improve catalytic activity compared to that of the catalyst without ZnO. The catalyst with the most ZnO content, Cu15ZnO, exhibited the highest activity, achieving methanol selectivity above 80% up to 260 °C and a methanol productivity of 0.32 gMeOH·gcat-1·h-1 for more than 80h. Once the best mass ratio was identified, 1 wt.% of Ba or Na was incorporated as promoters. Both promoted catalysts showed enhanced CO2 conversion and high methanol selectivity in the whole range of temperature evaluated. The use of Ba as promoter yielded the best results, reaching a CO2 conversion of 12% and a methanol selectivity of 95% at 260 °C, with a methanol productivity of 0.7 gMeOH·gcat-1·h-1. The catalytic activity and selectivity of this catalyst is considerably higher than those of a commercial Cu/ZnO catalyst and other copper-based catalysts reported in the literature, at similar operation conditions. The use of residual biomass as carbon precursor improves the sustainability of the catalytic system and methanol production.
- 8 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSELECTIVE PRODUCTION OF METHANOL BY CO2 HYDROGENATION OVER Cu-ZnO CARBON CATALYSTS DERIVED FROM RESIDUAL BIOMASS
The production of renewable methanol via CO2 hydrogenation was investigated using carbon-based Cu/ZnO catalysts. An activated carbon prepared by physical activation of residual olive stone with CO2 was used as catalyst support. Different Cu/ZnO mass ratios were used to identify the more efficient ZnO loading, fixing the copper content, approximately, at 10 wt.%. Catalysts performance was evaluated at H2/CO2= 3/1, GHSV= 11250 mL·g-1·h-1, 30 bar, and temperatures between 180 and 300 °C. The incorporation of ZnO, even at low loadings, decreased copper particle size and enhanced CO2 chemisorption, leading to improve catalytic activity compared to that of the catalyst without ZnO. The catalyst with the most ZnO content, Cu15ZnO, exhibited the highest activity, achieving methanol selectivity above 80% up to 260 °C and a methanol productivity of 0.32 gMeOH·gcat-1·h-1 for more than 80h. Once the best mass ratio was identified, 1 wt.% of Ba or Na was incorporated as promoters. Both promoted catalysts showed enhanced CO2 conversion and high methanol selectivity in the whole range of temperature evaluated. The use of Ba as promoter yielded the best results, reaching a CO2 conversion of 12% and a methanol selectivity of 95% at 260 °C, with a methanol productivity of 0.7 gMeOH·gcat-1·h-1. The catalytic activity and selectivity of this catalyst is considerably higher than those of a commercial Cu/ZnO catalyst and other copper-based catalysts reported in the literature, at similar operation conditions. The use of residual biomass as carbon precursor improves the sustainability of the catalytic system and methanol production.
- Open Access
Self-Standing Carbon Fiber Electrodes Doped with Pd Nanoparticles as Electrocatalysts in Zinc–Air Batteries
In this work, the effect of the palladium precursor on the Oxygen Reduction Reaction (ORR) performance of lignin-based electrospun carbon fibers was studied. The fibers were spun from a lignin-ethanol solution free of any binder, where different Pd salts were added at two concentration levels. The system implemented to perform the spinning was a coaxial setup in which the internal flow contains the precursor dispersion with the metallic precursor, and ethanol was used as external flow to help fiber formation and prevent drying before generating the Taylor cone. The obtained cloths were thermostabilized in air at 200 °C and carbonized in nitrogen at 900 °C. The resulting carbon fibers were characterized by physicochemical and electrochemical techniques. The palladium precursor significantly affects nanoparticle distribution and size, fiber diameter, pore distribution, surface area and electrochemical behavior. The fibers prepared with palladium acetylacetonate at high Pd loading and carbonized at 900 °C under a CO2 atmosphere showed high mechanical stability and the best ORR activity, showing near total selectivity towards the 4-electron path. These features are comparable to those of the commercial Pt/C catalyst but much lower metal loading (10.6 wt.% vs. 20 wt.%). The most promising fibers have been evaluated as cathodes in a zinc–air battery, delivering astonishing stability results that surpassed the performance of commercial Pt/C materials in both charging and discharging processes.
Open AccessSelf-Standing Carbon Fiber Electrodes Doped with Pd Nanoparticles as Electrocatalysts in Zinc–Air Batteries
In this work, the effect of the palladium precursor on the Oxygen Reduction Reaction (ORR) performance of lignin-based electrospun carbon fibers was studied. The fibers were spun from a lignin-ethanol solution free of any binder, where different Pd salts were added at two concentration levels. The system implemented to perform the spinning was a coaxial setup in which the internal flow contains the precursor dispersion with the metallic precursor, and ethanol was used as external flow to help fiber formation and prevent drying before generating the Taylor cone. The obtained cloths were thermostabilized in air at 200 °C and carbonized in nitrogen at 900 °C. The resulting carbon fibers were characterized by physicochemical and electrochemical techniques. The palladium precursor significantly affects nanoparticle distribution and size, fiber diameter, pore distribution, surface area and electrochemical behavior. The fibers prepared with palladium acetylacetonate at high Pd loading and carbonized at 900 °C under a CO2 atmosphere showed high mechanical stability and the best ORR activity, showing near total selectivity towards the 4-electron path. These features are comparable to those of the commercial Pt/C catalyst but much lower metal loading (10.6 wt.% vs. 20 wt.%). The most promising fibers have been evaluated as cathodes in a zinc–air battery, delivering astonishing stability results that surpassed the performance of commercial Pt/C materials in both charging and discharging processes.
- Open Access
- 19 February 2025
- Published by Elsevier in Biomass and Bioenergy
- Vol. 196
An integrated approach to the valorization of pyrolysis products from lignocellulosic residues and by-products
- 19 February 2025
- Published by Elsevier in Biomass and Bioenergy
- Vol. 196
Open AccessAn integrated approach to the valorization of pyrolysis products from lignocellulosic residues and by-products
- Open Access
- 12 February 2025
- Published by Elsevier in Education for Chemical Engineers
- Vol. 51, 34-42
Simulating a sustainable biorefinery process as autonomous learning tool for collaborative work in the chemical engineering degree
- 12 February 2025
- Published by Elsevier in Education for Chemical Engineers
- Vol. 51, 34-42
Open AccessSimulating a sustainable biorefinery process as autonomous learning tool for collaborative work in the chemical engineering degree
- Open Access
- 21 December 2024
- Published by Elsevier in Biomass and Bioenergy
- Vol. 193
Oxidative electrochemical depolymerization of lignin using highly active self-standing electrocatalysts prepared by electrospinning of lignin
- 21 December 2024
- Published by Elsevier in Biomass and Bioenergy
- Vol. 193
Open AccessOxidative electrochemical depolymerization of lignin using highly active self-standing electrocatalysts prepared by electrospinning of lignin
- Open Access
Carbon-Based Catalysts from H3PO4 Activation of Olive Stones for Sustainable Solketal and γ-Valerolactone Production
The use of activated carbon-based catalysts for the production of solketal and γ-valerolactone (GVL), two products of interest for biorefinery processes, was investigated. Activated carbons (ACs) were prepared by chemical activation of olive stones, an agricultural byproduct, using H3PO4 to olive stone mass impregnation ratios (IRs) of 1:1 and 3:1, and under nitrogen or air atmosphere. The ACs showed SBET values of 1130–1515 m2/g, owing to the presence of micropores (0.45–0.60 cm3/g). The use of an IR of 3:1 delivered a wider pore size distribution, with mesopore volume increasing up to 1.36 cm3/g. XPS confirmed the presence of phosphorus groups with surface concentrations of 2.2–3.2 wt% strongly bonded the AC surface through C-O-P bonds. The ACs were tested as acid catalysts for the acetalization of glycerol in a stirred batch reactor at temperatures of 30–50 °C, glycerol concentrations of 1.5 to 3.4 mol/L, and 1–3 wt% catalytic loading. The catalytic activity was clearly correlated with the quantity of C-O-P acid groups determined by TPD, which increased when ACs were prepared under air atmosphere. The AC prepared with IR 3:1 under air achieved full selectivity to solketal, with activation energy of 49 kJ/mol and conversion of up to 70%, matching the equilibrium conversion value under the optimum reaction conditions. A bifunctional catalyst was prepared over this AC by deposition of 5 wt% zirconium and tested in stirred batch reactor for the hydrogenation of levulinic acid (LA) using isopropyl alcohol (IPA) as solvent and H2 donor, with LA:IPA ratios from 1:1 to 1:7 and temperatures between 160–200 °C. The catalyst reached full LA conversion and a GVL yield higher than 80% after only 12 h at 200 °C. A test conducted in the presence of water revealed that it was an inhibitor of the reaction. The identification of isopropyl levulinate as an intermediate suggests that the most likely reaction pathway was dehydration, followed by hydrogenation and cyclization, to obtain GVL. Kinetic modelling of the results showed a value of 42 kJ/mol for the hydrogenation step. The reusability of the catalyst was tested for five consecutive reaction cycles, maintaining most of the activity and selectivity towards GVL.
Open AccessCarbon-Based Catalysts from H3PO4 Activation of Olive Stones for Sustainable Solketal and γ-Valerolactone Production
The use of activated carbon-based catalysts for the production of solketal and γ-valerolactone (GVL), two products of interest for biorefinery processes, was investigated. Activated carbons (ACs) were prepared by chemical activation of olive stones, an agricultural byproduct, using H3PO4 to olive stone mass impregnation ratios (IRs) of 1:1 and 3:1, and under nitrogen or air atmosphere. The ACs showed SBET values of 1130–1515 m2/g, owing to the presence of micropores (0.45–0.60 cm3/g). The use of an IR of 3:1 delivered a wider pore size distribution, with mesopore volume increasing up to 1.36 cm3/g. XPS confirmed the presence of phosphorus groups with surface concentrations of 2.2–3.2 wt% strongly bonded the AC surface through C-O-P bonds. The ACs were tested as acid catalysts for the acetalization of glycerol in a stirred batch reactor at temperatures of 30–50 °C, glycerol concentrations of 1.5 to 3.4 mol/L, and 1–3 wt% catalytic loading. The catalytic activity was clearly correlated with the quantity of C-O-P acid groups determined by TPD, which increased when ACs were prepared under air atmosphere. The AC prepared with IR 3:1 under air achieved full selectivity to solketal, with activation energy of 49 kJ/mol and conversion of up to 70%, matching the equilibrium conversion value under the optimum reaction conditions. A bifunctional catalyst was prepared over this AC by deposition of 5 wt% zirconium and tested in stirred batch reactor for the hydrogenation of levulinic acid (LA) using isopropyl alcohol (IPA) as solvent and H2 donor, with LA:IPA ratios from 1:1 to 1:7 and temperatures between 160–200 °C. The catalyst reached full LA conversion and a GVL yield higher than 80% after only 12 h at 200 °C. A test conducted in the presence of water revealed that it was an inhibitor of the reaction. The identification of isopropyl levulinate as an intermediate suggests that the most likely reaction pathway was dehydration, followed by hydrogenation and cyclization, to obtain GVL. Kinetic modelling of the results showed a value of 42 kJ/mol for the hydrogenation step. The reusability of the catalyst was tested for five consecutive reaction cycles, maintaining most of the activity and selectivity towards GVL.
- Open Access
- 26 April 2024
- Published by Elsevier in Chemical Engineering Science
- Vol. 295
Kinetic study of propane ODH on electrospun vanadium oxide-based submicron diameter fiber catalyst
- 26 April 2024
- Published by Elsevier in Chemical Engineering Science
- Vol. 295
Open AccessKinetic study of propane ODH on electrospun vanadium oxide-based submicron diameter fiber catalyst
- Open Access
- 12 April 2024
- Published by Elsevier in Environmental Research
- Vol. 252 (Pt 2) , 118918
Evaluation of acetanilide and antipyrine adsorption on lignin-derived activated carbons
- 12 April 2024
- Published by Elsevier in Environmental Research
- Vol. 252 (Pt 2) , 118918
Open AccessEvaluation of acetanilide and antipyrine adsorption on lignin-derived activated carbons