Shuhn-Shyurng Hou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shuhn-Shyurng Hou has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Ta-Hui Lin
Department of Mechanical Engineering, National Cheng Kung University, Tainan 70101, Taiwan
16 shared publications Ta-Hui Lin
14 shared publicationsJiann-Chang Lin
10 shared publications- Ming-Chien Hsiao
Department of Environmental Engineering, Kun Shan University, Tainan 71070, Taiwan
6 shared publications Yung-Chang Ko
China Steel
4 shared publicationsChung-Yao Hsuan
3 shared publications
Latest Publications
- 1 April 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (4) , 041001
Sheaf-Like Carbon Nanotube Composite Architectures for High-Performance Supercapacitor Electrodes in Concentrated Alkaline Media
For core materials with fast response times and adjustable power and energy output for energy storage, we herein report the electrochemical performance and latent hydrogen evolution reaction of sheaf-like carbon nanotube (s-CNT) based material electrodes, aiming for further low-cost synthesis and environmentally friendly supercapacitor applications. XPS scanning spectra show C, O, and a few Mo elements with estimated contents of 82.3, 17.2, and 0.5 at%, respectively. The maximum capacitance of 1287 F g ‒1 is achieved in the s-CNT-based electrochemical double-layer capacitor (EDLC) due to slow ion diffusion in the s-CNT-based electrode during charging and discharging. The Bode phase angle at 80.1° of the s-CNT electrode is close to 90°, and the prepared s-CNT electrode illustrates ideal EDLC capacitance behavior. In addition, the s-CNT electrode, after 2000 subsequent CV and GCD cycles at a current density of 0.95 A g ‒1 , retains specific capacitance of 96.8% and 80.55%, respectively. The s-CNT electrode exhibits reduced ionic resistance and facilitates ion transport through its conductive architecture, demonstrating its potential as a high-performance material for prospective EDLC supercapacitor applications.
- 1 April 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (4) , 041001
Sheaf-Like Carbon Nanotube Composite Architectures for High-Performance Supercapacitor Electrodes in Concentrated Alkaline Media
For core materials with fast response times and adjustable power and energy output for energy storage, we herein report the electrochemical performance and latent hydrogen evolution reaction of sheaf-like carbon nanotube (s-CNT) based material electrodes, aiming for further low-cost synthesis and environmentally friendly supercapacitor applications. XPS scanning spectra show C, O, and a few Mo elements with estimated contents of 82.3, 17.2, and 0.5 at%, respectively. The maximum capacitance of 1287 F g ‒1 is achieved in the s-CNT-based electrochemical double-layer capacitor (EDLC) due to slow ion diffusion in the s-CNT-based electrode during charging and discharging. The Bode phase angle at 80.1° of the s-CNT electrode is close to 90°, and the prepared s-CNT electrode illustrates ideal EDLC capacitance behavior. In addition, the s-CNT electrode, after 2000 subsequent CV and GCD cycles at a current density of 0.95 A g ‒1 , retains specific capacitance of 96.8% and 80.55%, respectively. The s-CNT electrode exhibits reduced ionic resistance and facilitates ion transport through its conductive architecture, demonstrating its potential as a high-performance material for prospective EDLC supercapacitor applications.
- Open Access
Enhanced Biodiesel Synthesis via a Homogenizer-Assisted Two-Stage Conversion Process Using Waste Edible Oil as Feedstock
In this study, a homogenizer in conjunction with a two-stage process was utilized to facilitate biodiesel production from waste edible oil (WEO). This paper contributes to the improvement of the yield and the shortening of the reaction time for biodiesel synthesis. Sulfuric acid was used in the first stage which was the esterification of the free fatty acids (FFA) of the WEO; then the transesterification reaction of triglycerides took place in the second stage with an alkaline catalysis. The present investigation aimed to explore the parameters affecting the reactions, including homogenizer speed, alcohol/oil molar ratio, catalyst dosage, reaction temperature, and reaction time. Under the operating conditions of the first stage (the reaction temperature was 65 °C, the homogenizer speed was 8000 rpm, the methanol/oil molar ratio was 15:1, and the amount of sulfuric acid was 4 wt%), the acid value fell to below 2 mg KOH/g after 10 min. The best base-catalyzed conditions in the second stage were: homogenizer speed of 8000 rpm, NaOH catalyst concentration of 1 wt%, methanol/oil molar ratio of 9:1 (mol/mol), reaction temperature of 65 °C, and reaction time 10 min. Consequently, the conversion rate from WEO to biodiesel achieved 97% after only 20 min, in line with the EU EN14214 standard, which requires a biodiesel production rate of at least 96.5%.
Open AccessEnhanced Biodiesel Synthesis via a Homogenizer-Assisted Two-Stage Conversion Process Using Waste Edible Oil as Feedstock
In this study, a homogenizer in conjunction with a two-stage process was utilized to facilitate biodiesel production from waste edible oil (WEO). This paper contributes to the improvement of the yield and the shortening of the reaction time for biodiesel synthesis. Sulfuric acid was used in the first stage which was the esterification of the free fatty acids (FFA) of the WEO; then the transesterification reaction of triglycerides took place in the second stage with an alkaline catalysis. The present investigation aimed to explore the parameters affecting the reactions, including homogenizer speed, alcohol/oil molar ratio, catalyst dosage, reaction temperature, and reaction time. Under the operating conditions of the first stage (the reaction temperature was 65 °C, the homogenizer speed was 8000 rpm, the methanol/oil molar ratio was 15:1, and the amount of sulfuric acid was 4 wt%), the acid value fell to below 2 mg KOH/g after 10 min. The best base-catalyzed conditions in the second stage were: homogenizer speed of 8000 rpm, NaOH catalyst concentration of 1 wt%, methanol/oil molar ratio of 9:1 (mol/mol), reaction temperature of 65 °C, and reaction time 10 min. Consequently, the conversion rate from WEO to biodiesel achieved 97% after only 20 min, in line with the EU EN14214 standard, which requires a biodiesel production rate of at least 96.5%.
- 13 September 2022
- Published by Elsevier in Molecular Catalysis
- Vol. 531
Kinetic model, recycling, regeneration, and reusing of tri-phase catalytic nucleophilic substitution esterification
- 13 September 2022
- Published by Elsevier in Molecular Catalysis
- Vol. 531
Kinetic model, recycling, regeneration, and reusing of tri-phase catalytic nucleophilic substitution esterification
- Open Access
Two-Stage Biodiesel Synthesis from Used Cooking Oil with a High Acid Value via an Ultrasound-Assisted Method
In this study, ultrasound was used to accelerate two-stage (esterification–transesterification) catalytic synthesis of biodiesel from used cooking oil, which originally had a high acid value (4.35 mg KOH/g). In the first stage, acid-catalyzed esterification reaction conditions were developed with a 9:1 methanol/oil molar ratio, sulfuric acid dosage at 2 wt %, and a reaction temperature of 60 °C. Under ultrasound irradiation for 40 min, the acid value was effectively decreased from 4.35 to 1.67 mg KOH/g, which was decreased to a sufficient level (<2 mg KOH/g) to avoid the saponification problem for the subsequent transesterification reaction. In the following stage, base-catalyzed transesterification reactions were carried out with a 12:1 methanol/oil molar ratio, a sodium hydroxide dosage of 1 wt %, and a reaction temperature of 65 °C. Under ultrasound-assisted transesterification for 40 min, the conversion rate of biodiesel reached 97.05%, which met the requirement of EN 14214 standard, i.e., 96.5% minimum. In order to evaluate and explore the improvement of the ultrasound-assisted two-stage (esterification–transesterification) process in shortening the reaction time, additional two-stage biodiesel synthesis experiments using the traditional mechanical stirring method under the optimal conditions were further carried out in this study. It was found that, under the same optimal conditions, using the ultrasound-assisted two-stage process, the total reaction time was significantly reduced to only 80 min, which was much shorter than the total time required by the conventional method of 140 min. It is worth noting that compared with the traditional method without ultrasound, the intensification of the ultrasound-assisted two-stage process significantly shortened the total time from 140 min to 80 min, which is a reduction of 42.9%. It was concluded that the ultrasound-assisted two-stage (esterification–transesterification) catalytic process is an effective and time-saving method for synthesizing biodiesel from used cooking oil with a high acid value.
Open AccessTwo-Stage Biodiesel Synthesis from Used Cooking Oil with a High Acid Value via an Ultrasound-Assisted Method
In this study, ultrasound was used to accelerate two-stage (esterification–transesterification) catalytic synthesis of biodiesel from used cooking oil, which originally had a high acid value (4.35 mg KOH/g). In the first stage, acid-catalyzed esterification reaction conditions were developed with a 9:1 methanol/oil molar ratio, sulfuric acid dosage at 2 wt %, and a reaction temperature of 60 °C. Under ultrasound irradiation for 40 min, the acid value was effectively decreased from 4.35 to 1.67 mg KOH/g, which was decreased to a sufficient level (<2 mg KOH/g) to avoid the saponification problem for the subsequent transesterification reaction. In the following stage, base-catalyzed transesterification reactions were carried out with a 12:1 methanol/oil molar ratio, a sodium hydroxide dosage of 1 wt %, and a reaction temperature of 65 °C. Under ultrasound-assisted transesterification for 40 min, the conversion rate of biodiesel reached 97.05%, which met the requirement of EN 14214 standard, i.e., 96.5% minimum. In order to evaluate and explore the improvement of the ultrasound-assisted two-stage (esterification–transesterification) process in shortening the reaction time, additional two-stage biodiesel synthesis experiments using the traditional mechanical stirring method under the optimal conditions were further carried out in this study. It was found that, under the same optimal conditions, using the ultrasound-assisted two-stage process, the total reaction time was significantly reduced to only 80 min, which was much shorter than the total time required by the conventional method of 140 min. It is worth noting that compared with the traditional method without ultrasound, the intensification of the ultrasound-assisted two-stage process significantly shortened the total time from 140 min to 80 min, which is a reduction of 42.9%. It was concluded that the ultrasound-assisted two-stage (esterification–transesterification) catalytic process is an effective and time-saving method for synthesizing biodiesel from used cooking oil with a high acid value.
- Open Access
Enhancement of Biodiesel Production from High-Acid-Value Waste Cooking Oil via a Microwave Reactor Using a Homogeneous Alkaline Catalyst
In this study, low quality oils (waste cooking oils) with high acid value (4.81 mg KOH/g) were utilized as the feedstocks for a transesterification reaction enhanced by additional microwave power and the use of an NaOH catalyst. The kinetics of the transesterification reaction under different reaction times and temperatures was studied. It was found that in the microwave-assisted transesterification reaction, the optimum conditions under a microwave power of 600 W were as follows: an NaOH catalyst of 0.8 wt %, a 12:1 molar ratio of methanol to oil, a reaction time of 2 min, and a reaction temperature of 65 °C. The conversion of waste cooking oil into biodiesel reached 98.2% after this short reaction time. This result conformed to 96.5% of the standard value of Taiwan CNS 15072. In addition, with increases in the reaction temperature from 55 to 65 °C, the reaction rate constant increased from 0.635 to 2.396 min−1, and the activation energy required for the transesterification reaction was 123.14 kJ/mole.
Open AccessEnhancement of Biodiesel Production from High-Acid-Value Waste Cooking Oil via a Microwave Reactor Using a Homogeneous Alkaline Catalyst
In this study, low quality oils (waste cooking oils) with high acid value (4.81 mg KOH/g) were utilized as the feedstocks for a transesterification reaction enhanced by additional microwave power and the use of an NaOH catalyst. The kinetics of the transesterification reaction under different reaction times and temperatures was studied. It was found that in the microwave-assisted transesterification reaction, the optimum conditions under a microwave power of 600 W were as follows: an NaOH catalyst of 0.8 wt %, a 12:1 molar ratio of methanol to oil, a reaction time of 2 min, and a reaction temperature of 65 °C. The conversion of waste cooking oil into biodiesel reached 98.2% after this short reaction time. This result conformed to 96.5% of the standard value of Taiwan CNS 15072. In addition, with increases in the reaction temperature from 55 to 65 °C, the reaction rate constant increased from 0.635 to 2.396 min−1, and the activation energy required for the transesterification reaction was 123.14 kJ/mole.
- Open Access
- 17 February 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (4) , 1362
Oxy-Fuel Combustion Characteristics of Pulverized Coal under O2/Recirculated Flue Gas Atmospheres
Oxy-fuel combustion is an effective technology for carbon capture and storage (CCS). Oxy-combustion for coal-fired power stations is a promising technology by which to diminish CO2 emissions. Unfortunately, little attention has been paid to the oxy-combustion characteristics affected by the combustion atmosphere. This paper is aimed at investigating the oxy-fuel combustion characteristics of Australian coal in a 0.3 MWth furnace. In particular, the influences of various oxygen flow rates and recirculated flue gas (RFG) on heating performance and pollutant emissions are examined in O2/RFG environments. The results show that with increases in the secondary RFG flow rate, the temperatures in the radiative and convective sections decrease and increase, respectively. At a lower oxygen flow rate, burning Australian coal emits lower residual oxygen and NO concentrations. In the flue gas, a high CO2 concentration of up to 94.8% can be achieved. Compared to air combustion, NO emissions are dramatically reduced up to 74% for Australian coal under oxy-combustion. Note that the high CO2 concentrations in the flue gas under oxy-coal combustions suggest great potential for reducing CO2 emissions through carbon capture and storage.
- 17 February 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (4) , 1362
Open AccessOxy-Fuel Combustion Characteristics of Pulverized Coal under O2/Recirculated Flue Gas Atmospheres
Oxy-fuel combustion is an effective technology for carbon capture and storage (CCS). Oxy-combustion for coal-fired power stations is a promising technology by which to diminish CO2 emissions. Unfortunately, little attention has been paid to the oxy-combustion characteristics affected by the combustion atmosphere. This paper is aimed at investigating the oxy-fuel combustion characteristics of Australian coal in a 0.3 MWth furnace. In particular, the influences of various oxygen flow rates and recirculated flue gas (RFG) on heating performance and pollutant emissions are examined in O2/RFG environments. The results show that with increases in the secondary RFG flow rate, the temperatures in the radiative and convective sections decrease and increase, respectively. At a lower oxygen flow rate, burning Australian coal emits lower residual oxygen and NO concentrations. In the flue gas, a high CO2 concentration of up to 94.8% can be achieved. Compared to air combustion, NO emissions are dramatically reduced up to 74% for Australian coal under oxy-combustion. Note that the high CO2 concentrations in the flue gas under oxy-coal combustions suggest great potential for reducing CO2 emissions through carbon capture and storage.
- Open Access
Study of Solid Calcium Diglyceroxide for Biodiesel Production from Waste Cooking Oil Using a High Speed Homogenizer
Biodiesel has been one of the potential candidates in the field of renewable energy due to its biodegradability and non-toxicity in the natural environment. In addition, due to its high boiling point, the transportation of biodiesel is much safer than that of conventional fuel. However, the cost remains a challenge for the development of biodiesel. In this study, a homogenizer system, which can intensively minimize raw materials, is utilized as an effective approach to assist the production of both the calcium diglyceroxide (CaDG) catalyst and biodiesel. Several operational factors were evaluated to obtain the optimal conditions, and a desirable biodiesel conversion of 77.24% was achieved at a methanol-to-oil molar ratio of 7, with 2.0 g of calcium diglyceroxide, a rotation speed of 7000 rpm, a reaction temperature of 65 °C and a reaction period of 90 min.
Open AccessStudy of Solid Calcium Diglyceroxide for Biodiesel Production from Waste Cooking Oil Using a High Speed Homogenizer
Biodiesel has been one of the potential candidates in the field of renewable energy due to its biodegradability and non-toxicity in the natural environment. In addition, due to its high boiling point, the transportation of biodiesel is much safer than that of conventional fuel. However, the cost remains a challenge for the development of biodiesel. In this study, a homogenizer system, which can intensively minimize raw materials, is utilized as an effective approach to assist the production of both the calcium diglyceroxide (CaDG) catalyst and biodiesel. Several operational factors were evaluated to obtain the optimal conditions, and a desirable biodiesel conversion of 77.24% was achieved at a methanol-to-oil molar ratio of 7, with 2.0 g of calcium diglyceroxide, a rotation speed of 7000 rpm, a reaction temperature of 65 °C and a reaction period of 90 min.