Yubin Yue
Yubin Yue has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Lingfeng Lai
Beijing Eastforce Superconducting Technology Company Ltd., Beijing, China
4 shared publications - Timing Qu
State Key Laboratory of Clean and Efficient Turbomachinery Power Equipment, Department of Mechanical Engineering, Tsinghua University, Beijing, China
4 shared publications - Yi Li
Princeton Plasma Physics Laboratory, Princeton, NJ, USA
3 shared publications Chen Gu
Teaching Center of Experimental Physics, Tsinghua University, Beijing, China
2 shared publications- Chen Gu
Teaching Center of Experimental Physics, Tsinghua University, Beijing, China
2 shared publications - Fang Liu
Institute of Plasma Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences
2 shared publications
Latest Publications
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. PP (10518223) , 1-5
A fitting algorithm for HTS cable measurement
Assembling HTS tapes into cables is an effective solution to enhance the operating current of superconducting devices. With the advancement of cable research and its practical engineering applications, the demand for quality control of cables is rapidly increasing. In this paper, a fitting algorithm for cable defect detection is being proposed. This algorithm can effectively extract defect information within the cable and identify and correct for movements including position displacement and rotation of the cable. The method has been validated using both simulation and experimental data from HTS tapes and cables.
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. PP (10518223) , 1-5
A fitting algorithm for HTS cable measurement
Assembling HTS tapes into cables is an effective solution to enhance the operating current of superconducting devices. With the advancement of cable research and its practical engineering applications, the demand for quality control of cables is rapidly increasing. In this paper, a fitting algorithm for cable defect detection is being proposed. This algorithm can effectively extract defect information within the cable and identify and correct for movements including position displacement and rotation of the cable. The method has been validated using both simulation and experimental data from HTS tapes and cables.
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Establishment of the Inductance Matrix of Uninsulated Superconducting Windings With Different Shapes and the Treatment of Their Singular Value Problems
In order to accurately and efficiently study the transient process of quenching in non-insulated superconducting windings, the Partial Element Equivalent Circuit (PEEC) model is employed. This model regards the superconducting winding as being composed of multiple independent segments. To establish the model parameter matrix, it is necessary to calculate the resistance and inductance parameters for each independent segment. Among these, the inductance parameters can be derived from the relationship between the magnetic vector potential A and the current density J. However, during the derivation process, when calculating the self-inductance of each segment, a singularity problem may arise. This issue can be resolved through the method of partial integration. This paper will elaborate on the derivation process of the inductance matrix for circular windings, straight laminations, and D-shaped windings, with a focus on the solution to the self-inductance singularity problem.
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Establishment of the Inductance Matrix of Uninsulated Superconducting Windings With Different Shapes and the Treatment of Their Singular Value Problems
In order to accurately and efficiently study the transient process of quenching in non-insulated superconducting windings, the Partial Element Equivalent Circuit (PEEC) model is employed. This model regards the superconducting winding as being composed of multiple independent segments. To establish the model parameter matrix, it is necessary to calculate the resistance and inductance parameters for each independent segment. Among these, the inductance parameters can be derived from the relationship between the magnetic vector potential A and the current density J. However, during the derivation process, when calculating the self-inductance of each segment, a singularity problem may arise. This issue can be resolved through the method of partial integration. This paper will elaborate on the derivation process of the inductance matrix for circular windings, straight laminations, and D-shaped windings, with a focus on the solution to the self-inductance singularity problem.
- Open Access
- 21 March 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (4) , 045012
Design and prototype testing of a contactless HTS cable measurement system
By combining multiple high-temperature superconducting tapes into cables and then fabricating them into devices such as power cable and magnets, the system operating current can be effectively increased and manufacturing process difficulties can be reduced. To improve system reliability, it is necessary to conduct quality inspections on cables before assembly. In this paper, a non-contact cable measurement method utilizing the screen current effect is proposed. The distribution characteristics of screen current in conductor on round core (CORC) cables under dynamic excitation magnetic fields, as well as the magnetic field characteristics produced in space, were analyzed through simulation by J model. It was found that the cable can be effectively measured by combining two sets of excitation magnets and sensor arrays. Subsequently, a prototype was established, and CORC samples with artificially created defects were measured. The experiments confirmed the feasibility of this method.
- 21 March 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (4) , 045012
Open AccessDesign and prototype testing of a contactless HTS cable measurement system
By combining multiple high-temperature superconducting tapes into cables and then fabricating them into devices such as power cable and magnets, the system operating current can be effectively increased and manufacturing process difficulties can be reduced. To improve system reliability, it is necessary to conduct quality inspections on cables before assembly. In this paper, a non-contact cable measurement method utilizing the screen current effect is proposed. The distribution characteristics of screen current in conductor on round core (CORC) cables under dynamic excitation magnetic fields, as well as the magnetic field characteristics produced in space, were analyzed through simulation by J model. It was found that the cable can be effectively measured by combining two sets of excitation magnets and sensor arrays. Subsequently, a prototype was established, and CORC samples with artificially created defects were measured. The experiments confirmed the feasibility of this method.
- 13 December 2024
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 224
An anomaly detection method for gas turbines based on single-condition training with zero-fault sample
- 13 December 2024
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 224
An anomaly detection method for gas turbines based on single-condition training with zero-fault sample
- 14 May 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (6) , 065014
Experimental study on screening-current induced strain in REBCO insert coils: under critical current control and operation current cycles
The screening-current effect is an inhomogeneous distribution of current density inside the REBCO conductors. The additional strain induced by the screening current, known as screening-current induced strain (SCS), is considered to affect the structural integrity of REBCO windings, especially when operating high-field REBCO insert magnets. In this work, we wound and tested a series of 50-turn REBCO coils inside a 10 T LTS external to investigate the influencing mechanism of multiple electromagnetic factors on SCS. We varied the critical current in different coils by different heat treatment procedures. Each coil was tested individually, experiencing a external field cycle and multiple operation current cycles at constant external fields. The extreme scenario for each coil was being energized to 400 A while the external field was 10 T. We adapted the discrete-coupled model to estimate the hoop strain distribution, monitored the experimental results by multiple strain gauges at the outermost turn. Test coil with a lower critical current endured a lower maximum hoop strain. When we were energizing the test coils, hoop strain increased at the edge of REBCO tapes while remaining nearly constant in the middle region. Additionally, the maximum hoop strain at the outermost turn decreased after each excitation cycle. This work could be an experimental reference for optimizing the electromagnetic design and the excitation scheme during the development of high-field REBCO magnets.
- 14 May 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (6) , 065014
Experimental study on screening-current induced strain in REBCO insert coils: under critical current control and operation current cycles
The screening-current effect is an inhomogeneous distribution of current density inside the REBCO conductors. The additional strain induced by the screening current, known as screening-current induced strain (SCS), is considered to affect the structural integrity of REBCO windings, especially when operating high-field REBCO insert magnets. In this work, we wound and tested a series of 50-turn REBCO coils inside a 10 T LTS external to investigate the influencing mechanism of multiple electromagnetic factors on SCS. We varied the critical current in different coils by different heat treatment procedures. Each coil was tested individually, experiencing a external field cycle and multiple operation current cycles at constant external fields. The extreme scenario for each coil was being energized to 400 A while the external field was 10 T. We adapted the discrete-coupled model to estimate the hoop strain distribution, monitored the experimental results by multiple strain gauges at the outermost turn. Test coil with a lower critical current endured a lower maximum hoop strain. When we were energizing the test coils, hoop strain increased at the edge of REBCO tapes while remaining nearly constant in the middle region. Additionally, the maximum hoop strain at the outermost turn decreased after each excitation cycle. This work could be an experimental reference for optimizing the electromagnetic design and the excitation scheme during the development of high-field REBCO magnets.
- 8 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-6
Degradation Characteristics of a 20 T REBCO Insert Magnet After a 4.2 K Standalone Test
A 20-T/17-mm High-Temperature-Superconducting (HTS) magnet was developed and tested, comprising a 15-T no-insulation (NI) REBCO insert (Coil 1) nested in a 5-T metal-insulation (MI) REBCO coil (Coil 2). Coil 1 consists of 20 NI double pancakes (DP), while Coil 2 consists of 28 MI DPs. The 20-T magnet was cooled in liquid helium and charged for five runs, the maximum power supply current reached 228.7 A. Multiple quenches occurred during the charging process, causing the power supply current to drop to zero within one second. The rapid current variation induced a large voltage inside the coil, which damaged Coil 1. After re-warming, Coil 1 was tested in liquid nitrogen, and its critical current was significantly degraded. To investigate the degradation, three representative DPs from Coil 1 were examined using continuous I c measurement and observed with optical microscope and scanning electron microscope (SEM). Most degradation areas consisted of a bubble with a current breakdown point distributed throughout Coil 1. Probable causes were proposed in this article.
- 8 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-6
Degradation Characteristics of a 20 T REBCO Insert Magnet After a 4.2 K Standalone Test
A 20-T/17-mm High-Temperature-Superconducting (HTS) magnet was developed and tested, comprising a 15-T no-insulation (NI) REBCO insert (Coil 1) nested in a 5-T metal-insulation (MI) REBCO coil (Coil 2). Coil 1 consists of 20 NI double pancakes (DP), while Coil 2 consists of 28 MI DPs. The 20-T magnet was cooled in liquid helium and charged for five runs, the maximum power supply current reached 228.7 A. Multiple quenches occurred during the charging process, causing the power supply current to drop to zero within one second. The rapid current variation induced a large voltage inside the coil, which damaged Coil 1. After re-warming, Coil 1 was tested in liquid nitrogen, and its critical current was significantly degraded. To investigate the degradation, three representative DPs from Coil 1 were examined using continuous I c measurement and observed with optical microscope and scanning electron microscope (SEM). Most degradation areas consisted of a bubble with a current breakdown point distributed throughout Coil 1. Probable causes were proposed in this article.
- Open Access
- 1 January 2023
- Published by Tech Science Press in Structural Durability & Health Monitoring
- Vol. 17 (4) , 315-336
Wireless Self-Powered Vibration Sensor System for Intelligent Spindle Monitoring
In recent years, high-end equipment is widely used in industry and the accuracy requirements of the equipment have been risen year by year. During the machining process, the high-end equipment failure may have a great impact on the product quality. It is necessary to monitor the status of equipment and to predict fault diagnosis. At present, most of the condition monitoring devices for mechanical equipment have problems of large size, low precision and low energy utilization. A wireless self-powered intelligent spindle vibration acceleration sensor system based on piezoelectric energy harvesting is proposed. Based on rotor sensing technology, a sensor is made to mount on the tool holder and build the related circuit. Firstly, the energy management module collects the mechanical energy in the environment and converts the piezoelectric vibration energy into electric energy to provide 3.3 V for the subsequent circuit. The lithium battery supplies the system with additional power and monitors’ the power of the energy storage circuit in real-time. Secondly, a three-axis acceleration sensor is used to collect, analyze and filter a series of signal processing operations of the vibration signal in the environment. The signal is sent to the upper computer by wireless transmission. The host computer outputs the corresponding X, Y, and Z channel waveforms and data under the condition of the spindle speed of 50∼2500 r/min with real-time monitoring. The KEIL5 platform is used to develop the system software. The small-size piezoelectric vibration sensor with high-speed, high-energy utilization, high accuracy, and easy installation is used for spindle monitoring. The experiment results show that the sensor system is available and practical.
- 1 January 2023
- Published by Tech Science Press in Structural Durability & Health Monitoring
- Vol. 17 (4) , 315-336
Open AccessWireless Self-Powered Vibration Sensor System for Intelligent Spindle Monitoring
In recent years, high-end equipment is widely used in industry and the accuracy requirements of the equipment have been risen year by year. During the machining process, the high-end equipment failure may have a great impact on the product quality. It is necessary to monitor the status of equipment and to predict fault diagnosis. At present, most of the condition monitoring devices for mechanical equipment have problems of large size, low precision and low energy utilization. A wireless self-powered intelligent spindle vibration acceleration sensor system based on piezoelectric energy harvesting is proposed. Based on rotor sensing technology, a sensor is made to mount on the tool holder and build the related circuit. Firstly, the energy management module collects the mechanical energy in the environment and converts the piezoelectric vibration energy into electric energy to provide 3.3 V for the subsequent circuit. The lithium battery supplies the system with additional power and monitors’ the power of the energy storage circuit in real-time. Secondly, a three-axis acceleration sensor is used to collect, analyze and filter a series of signal processing operations of the vibration signal in the environment. The signal is sent to the upper computer by wireless transmission. The host computer outputs the corresponding X, Y, and Z channel waveforms and data under the condition of the spindle speed of 50∼2500 r/min with real-time monitoring. The KEIL5 platform is used to develop the system software. The small-size piezoelectric vibration sensor with high-speed, high-energy utilization, high accuracy, and easy installation is used for spindle monitoring. The experiment results show that the sensor system is available and practical.
- 25 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-4
Open Magnetic Shielding by Superconducting Technology
Until recently, a new type of open magnetic shielding system was realized by the combination of a series of closed high temperature superconductor coils. We experimentally confirmed that the shielding factor (SF) of the new shielding system can reach more than 40 dB in the frequency spectrum of 0.1-16,000 Hz. Because of its superior ability to resist alternative magnetic field, we name the system Tesla-shielding (TS), to commemorate the father of alternative current (AC), Nikola Tesla. In this paper, we will report the design and realization of a Helmholtz coil based TS. The Helmholtz TS has many advantages over the previous planar TS. Especially, the Helmholtz TS has an engineering way of regulating the device for a better SF. We will introduce the design of the Helmholtz TS with the help of numerical simulation. The main electromagnetic properties of the TS, such as SF in the frequency spectrum and its shielding ability in the long duration measurement are given in this paper.
- 25 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-4
Open Magnetic Shielding by Superconducting Technology
Until recently, a new type of open magnetic shielding system was realized by the combination of a series of closed high temperature superconductor coils. We experimentally confirmed that the shielding factor (SF) of the new shielding system can reach more than 40 dB in the frequency spectrum of 0.1-16,000 Hz. Because of its superior ability to resist alternative magnetic field, we name the system Tesla-shielding (TS), to commemorate the father of alternative current (AC), Nikola Tesla. In this paper, we will report the design and realization of a Helmholtz coil based TS. The Helmholtz TS has many advantages over the previous planar TS. Especially, the Helmholtz TS has an engineering way of regulating the device for a better SF. We will introduce the design of the Helmholtz TS with the help of numerical simulation. The main electromagnetic properties of the TS, such as SF in the frequency spectrum and its shielding ability in the long duration measurement are given in this paper.
- 6 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-4
Inductance of Low-Frequency Small-Scale High-Temperature Superconducting Coils
Inductance is a very commonly used electrical parameter in transient progress analysis, as well as in energy storage evaluations. It was normally considered as constant when the geometrical configuration of a coil is determined. However, experiments on Bi-2223 (Bi 2 Sr 2 Ca 2 Cu 3 O 10+x ) and YBCO (YBa 2 Cu 4 O 7-x ) coils, both show 10% rise inductance while increasing the applied current. The inductance grows approximately a linear relationship from its minimum to maximum. We used both theoretical and experimental analysis to deeply understand the mechanism of the variation in terms of current distribution in high-temperature superconducting (HTS) coils. Taking this inductance change into account would benefit the accuracy in energy storage applications and in transient analysis occasions. Besides, inductance controllable devices could be achieved by manipulating the bias current applied on HTS coils.
- 6 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-4
Inductance of Low-Frequency Small-Scale High-Temperature Superconducting Coils
Inductance is a very commonly used electrical parameter in transient progress analysis, as well as in energy storage evaluations. It was normally considered as constant when the geometrical configuration of a coil is determined. However, experiments on Bi-2223 (Bi 2 Sr 2 Ca 2 Cu 3 O 10+x ) and YBCO (YBa 2 Cu 4 O 7-x ) coils, both show 10% rise inductance while increasing the applied current. The inductance grows approximately a linear relationship from its minimum to maximum. We used both theoretical and experimental analysis to deeply understand the mechanism of the variation in terms of current distribution in high-temperature superconducting (HTS) coils. Taking this inductance change into account would benefit the accuracy in energy storage applications and in transient analysis occasions. Besides, inductance controllable devices could be achieved by manipulating the bias current applied on HTS coils.