Seok-Hee Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Seok-Hee Park has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Sung-Dae Yim
Korea Institute of Energy Research
6 shared publications Seunghee Woo
Hydrogen Fuel Cell Laboratory Korea Institute of Energy Research (KIER) Daejeon Republic of Korea
4 shared publications- Namgee Jung
Graduate School of Energy Science and Technology (GEST) Chungnam National University Daejeon Republic of Korea
3 shared publications - Seunghee Woo
Fuel Cell Laboratory, Korea Institute of Energy Research, Daejeon, South Korea
3 shared publications Sungmin Kim
Hydrogen Fuel Cell Laboratory Korea Institute of Energy Research (KIER) Daejeon Republic of Korea
2 shared publicationsTae-Hyun Yang
2 shared publications
Latest Publications
- 31 October 2026
- Published by Wiley in Fuel Cells
- Vol. 26 (6)
Effects of Carbon Support Structure and Ionomer Equivalent Weight on Catalyst Ink Rheology and Fuel Cell Performance
This study investigates how Pt/C catalyst structure, including carbon support porosity and surface properties, and ionomer equivalent weight (EW) affect catalyst ink rheology and coating behavior for polymer electrolyte membrane fuel cells. Four Pt/C catalysts with porous or less porous supports and different surface wettabilities are formulated with short‐side‐chain perfluorosulfonic acid ionomers at three EWs and a fixed ionomer‐to‐carbon ratio. Ink viscosity, viscoelasticity, thixotropic recovery, aggregate size, and slurry resistance are characterized and linked to coating integrity. Pt/C catalysts with porous supports form gel‐like, shear‐thinning catalyst inks with rapid structural recovery, producing relatively uniform catalyst layers, whereas less porous supports yield low‐viscosity catalyst inks prone to cracking. EW effects depend on support properties: Increasing EW raises viscosity for porous hydrophilic catalysts, has little effect on viscosity for porous hydrophobic catalysts, and impairs recovery and coating integrity for less porous‐support catalysts. These results provide practical insight for catalyst ink formulation.
- 31 October 2026
- Published by Wiley in Fuel Cells
- Vol. 26 (6)
Effects of Carbon Support Structure and Ionomer Equivalent Weight on Catalyst Ink Rheology and Fuel Cell Performance
This study investigates how Pt/C catalyst structure, including carbon support porosity and surface properties, and ionomer equivalent weight (EW) affect catalyst ink rheology and coating behavior for polymer electrolyte membrane fuel cells. Four Pt/C catalysts with porous or less porous supports and different surface wettabilities are formulated with short‐side‐chain perfluorosulfonic acid ionomers at three EWs and a fixed ionomer‐to‐carbon ratio. Ink viscosity, viscoelasticity, thixotropic recovery, aggregate size, and slurry resistance are characterized and linked to coating integrity. Pt/C catalysts with porous supports form gel‐like, shear‐thinning catalyst inks with rapid structural recovery, producing relatively uniform catalyst layers, whereas less porous supports yield low‐viscosity catalyst inks prone to cracking. EW effects depend on support properties: Increasing EW raises viscosity for porous hydrophilic catalysts, has little effect on viscosity for porous hydrophobic catalysts, and impairs recovery and coating integrity for less porous‐support catalysts. These results provide practical insight for catalyst ink formulation.
- 23 September 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 623
Electrochemical analysis and recovery methods for high-voltage-induced degradation in polymer electrolyte membrane fuel cells
- 23 September 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 623
Electrochemical analysis and recovery methods for high-voltage-induced degradation in polymer electrolyte membrane fuel cells
- 25 September 2023
- Published by Elsevier in Journal of Power Sources
- Vol. 585
Ink droplet drying analysis for understanding the ink-catalyst layer transition in proton exchange membrane fuel cells
- 25 September 2023
- Published by Elsevier in Journal of Power Sources
- Vol. 585
Ink droplet drying analysis for understanding the ink-catalyst layer transition in proton exchange membrane fuel cells
- Open Access
- 25 June 2021
- Published by The Korean Society for New and Renewable Energy in New & Renewable Energy
- Vol. 17 (2) , 50-58
Optimization Method for MEA Performance Considering the Non-Uniformity of Operating Condition in a Large-area Bipolar Plate
- 25 June 2021
- Published by The Korean Society for New and Renewable Energy in New & Renewable Energy
- Vol. 17 (2) , 50-58
Open AccessOptimization Method for MEA Performance Considering the Non-Uniformity of Operating Condition in a Large-area Bipolar Plate
- 31 December 2018
- Published by The Korean Society for New and Renewable Energy in New & Renewable Energy
- Vol. 14 (4) , 38-45
Study on the CO Tolerance of Anode Catalyst Layers with Ionomer Content for Polymer Electrolyte Membrane Fuel Cells
This paper reports the effects of the ionomer content on CO tolerance in a PtRu/C-based anode catalyst layer to understand the role of ionomer binders for CO poisoning of the electrocatalyst and to design a durable catalyst layer of MEA. Four different MEAs were prepared with ionomer contents of 20, 30, 40, and 50 wt. % for the anode and a fixed ionomer content of 30 wt. % for the cathode. The MEA performance was then tested under hydrogen and CO mixed gas feeding in a single cell to observe the CO tolerance of the prepared MEAs. The MEA performance was largely dependent on the anode ionomer content under both hydrogen and CO mixed gas conditions, revealing the best cell performance at a 40 wt. % ionomer content. The MEA also showed the lowest cell potential decay under CO mixed gas compared to hydrogen at a 40 wt. % ionomer content. The present study provides insights into the design of an anode catalyst layer structure, including optimization of the ionomer content, which can be critical to the design of a high performance MEA for reformed gas applications.
- 31 December 2018
- Published by The Korean Society for New and Renewable Energy in New & Renewable Energy
- Vol. 14 (4) , 38-45
Study on the CO Tolerance of Anode Catalyst Layers with Ionomer Content for Polymer Electrolyte Membrane Fuel Cells
This paper reports the effects of the ionomer content on CO tolerance in a PtRu/C-based anode catalyst layer to understand the role of ionomer binders for CO poisoning of the electrocatalyst and to design a durable catalyst layer of MEA. Four different MEAs were prepared with ionomer contents of 20, 30, 40, and 50 wt. % for the anode and a fixed ionomer content of 30 wt. % for the cathode. The MEA performance was then tested under hydrogen and CO mixed gas feeding in a single cell to observe the CO tolerance of the prepared MEAs. The MEA performance was largely dependent on the anode ionomer content under both hydrogen and CO mixed gas conditions, revealing the best cell performance at a 40 wt. % ionomer content. The MEA also showed the lowest cell potential decay under CO mixed gas compared to hydrogen at a 40 wt. % ionomer content. The present study provides insights into the design of an anode catalyst layer structure, including optimization of the ionomer content, which can be critical to the design of a high performance MEA for reformed gas applications.
- 1 August 2017
- Published by Elsevier in Journal of Power Sources
- Vol. 359, 568-576
Synthesis and characterization of anion exchange multi-block copolymer membranes with a fluorine moiety as alkaline membrane fuel cells
- 1 August 2017
- Published by Elsevier in Journal of Power Sources
- Vol. 359, 568-576
Synthesis and characterization of anion exchange multi-block copolymer membranes with a fluorine moiety as alkaline membrane fuel cells
- 1 September 2016
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2016-02 (38) , 2544
CNTs Grown on Al2O3 Spheres As an Efficient Catalyst Support for High Performance MEA in PEM Fuel Cells
Polymer electrolyte membrane fuel cells (PEMFCs) have been widely accepted as a clean energy device because of its capability of generating high energy density and only water as a product via direct converting of the chemical energy into the electrical energy. However, durability problems originating from the carbon corrosion and Pt agglomeration have been one of the major issues for practical applications. The high potentials formed in a cell during the fuel cell operations lead to serious carbon corrosion in catalyst layers, which causes the decrease of cell performance. To resolve the carbon corrosion, highly durable carbon materials such as carbon nanotubes (CNTs) have been intensively studied. Although the corrosion-resistant characteristics of CNTs were efficient to utilize as an electrocatalyst support for PEMFCs, the difficulty in processing the CNTs mainly due to poor dispersibility and easy bundle formation in a catalyst ink limited their practical applications. In this respect, vertically aligned carbon nanotubes (VACNTs) have been tried and showed promising results in a PEMFC MEA. However, VACNTs need complex process to make MEAs, remaining the issues of mass production. In this work, we report CNTs grown on Al2O3 (Al2O3-CNT) as an efficient support material for PEMFC MEAs. The catalyst support was designed to utilize durable CNT properties while resolving the CNT bundling problems. The catalyst was characterized by transmission electron microscope (TEM), field emission scanning spectroscopy (FESEM), and X-ray photoelectron spectroscopy (XPS) in order to investigate structural and electronic properties. The kinetics of O2 reduction is examined with the rotating disk electrode (RDE) technique. A potential cycling test was applied to evaluate durability of the catalyst. The electrochemical surface area (ECSA) of Pt/Al2O3-CNT slightly decreased (17 %), while Pt/C loses nearly 46 % of its ECSA of its initial value over repeated cycling test under carbon corrosion potential range, representing more durable properties of CNTs. The single cell test was also performed with Pt/Al2O3-CNT and Pt/C after fabricating the catalysts to MEAs. The performance of the Pt/Al2O3-CNT was comparable to that of Pt/C and showed better performance at high current density regions. Furthermore, after the accelerated stress test (AST), the Pt/Al2O3-CNT also showed approximately 2 times higher stability than Pt/C in a single cell test.
- 1 September 2016
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2016-02 (38) , 2544
CNTs Grown on Al2O3 Spheres As an Efficient Catalyst Support for High Performance MEA in PEM Fuel Cells
Polymer electrolyte membrane fuel cells (PEMFCs) have been widely accepted as a clean energy device because of its capability of generating high energy density and only water as a product via direct converting of the chemical energy into the electrical energy. However, durability problems originating from the carbon corrosion and Pt agglomeration have been one of the major issues for practical applications. The high potentials formed in a cell during the fuel cell operations lead to serious carbon corrosion in catalyst layers, which causes the decrease of cell performance. To resolve the carbon corrosion, highly durable carbon materials such as carbon nanotubes (CNTs) have been intensively studied. Although the corrosion-resistant characteristics of CNTs were efficient to utilize as an electrocatalyst support for PEMFCs, the difficulty in processing the CNTs mainly due to poor dispersibility and easy bundle formation in a catalyst ink limited their practical applications. In this respect, vertically aligned carbon nanotubes (VACNTs) have been tried and showed promising results in a PEMFC MEA. However, VACNTs need complex process to make MEAs, remaining the issues of mass production. In this work, we report CNTs grown on Al2O3 (Al2O3-CNT) as an efficient support material for PEMFC MEAs. The catalyst support was designed to utilize durable CNT properties while resolving the CNT bundling problems. The catalyst was characterized by transmission electron microscope (TEM), field emission scanning spectroscopy (FESEM), and X-ray photoelectron spectroscopy (XPS) in order to investigate structural and electronic properties. The kinetics of O2 reduction is examined with the rotating disk electrode (RDE) technique. A potential cycling test was applied to evaluate durability of the catalyst. The electrochemical surface area (ECSA) of Pt/Al2O3-CNT slightly decreased (17 %), while Pt/C loses nearly 46 % of its ECSA of its initial value over repeated cycling test under carbon corrosion potential range, representing more durable properties of CNTs. The single cell test was also performed with Pt/Al2O3-CNT and Pt/C after fabricating the catalysts to MEAs. The performance of the Pt/Al2O3-CNT was comparable to that of Pt/C and showed better performance at high current density regions. Furthermore, after the accelerated stress test (AST), the Pt/Al2O3-CNT also showed approximately 2 times higher stability than Pt/C in a single cell test.