Punathil Raman Sreeram
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Punathil Raman Sreeram has a total of 83 co-authors. Here are the top co-authors by number of shared publications:
- Chandra Sekhar Tiwary
Indian Institute of Technology Kharagpur
20 shared publications Karthik R
Department of Metallurgical and Materials Engineering
9 shared publicationsAppu Kumar Singh
Department of Metallurgical and Materials Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
6 shared publications- Abhishek Kumar Singh
Materials Research Centre Indian Institute of Science Bangalore Karnataka India
5 shared publications Kamanio Chattopadhyay
5 shared publications- Aniruddh Vashisth
University of Washington
4 shared publications
Latest Publications
- 12 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (4) , 1600-1613
Localized RF Heating-Driven Thermoelectric Power Generation in Natural Galena (PbS)
- 12 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (4) , 1600-1613
Localized RF Heating-Driven Thermoelectric Power Generation in Natural Galena (PbS)
- 18 January 2026
- Published by Wiley in Advanced Sustainable Systems
- Vol. 10 (1)
Scalable and Sustainable Growth of Bronze Telluride for Thermoelectric Energy Harvesting
With the growing demand for sustainable and decentralized energy solutions, thermoelectric energy harvesting has emerged as a promising technology for directly converting waste heat into electricity through solid‐state, environmentally friendly means. Among copper chalcogenides, Cu 2 Te is a notable p‐type material due to its degenerate semiconducting nature and low thermal conductivity. In this study, we present a sustainable synthesis strategy for Sn‐doped Cu 2 Te referred to as bronze telluride (BT) via a chemical vapor deposition (CVD)‐assisted tellurization process using pre‐alloyed Cu–Sn (bronze) powder. The resulting BT exhibited an enhanced thermoelectric figure of merit (ZT) of ∼1 at 500 K. To assess practical applicability, BT is integrated with n‐type galena (PbS) in a cascaded p–n thermoelectric module, which generated 2.8 mV across a temperature gradient of 33 K, demonstrating its potential for medium‐ to high‐temperature waste heat recovery. Furthermore, thermodynamic calculations and density functional theory (DFT) simulations provided insights into the formation mechanism of Cu 2 Te and the thermoelectric behaviour of BT. This work introduces an efficient, scalable, and environmentally responsible pathway for developing copper‐based thermoelectric materials using industrially relevant precursors.
- 18 January 2026
- Published by Wiley in Advanced Sustainable Systems
- Vol. 10 (1)
Scalable and Sustainable Growth of Bronze Telluride for Thermoelectric Energy Harvesting
With the growing demand for sustainable and decentralized energy solutions, thermoelectric energy harvesting has emerged as a promising technology for directly converting waste heat into electricity through solid‐state, environmentally friendly means. Among copper chalcogenides, Cu 2 Te is a notable p‐type material due to its degenerate semiconducting nature and low thermal conductivity. In this study, we present a sustainable synthesis strategy for Sn‐doped Cu 2 Te referred to as bronze telluride (BT) via a chemical vapor deposition (CVD)‐assisted tellurization process using pre‐alloyed Cu–Sn (bronze) powder. The resulting BT exhibited an enhanced thermoelectric figure of merit (ZT) of ∼1 at 500 K. To assess practical applicability, BT is integrated with n‐type galena (PbS) in a cascaded p–n thermoelectric module, which generated 2.8 mV across a temperature gradient of 33 K, demonstrating its potential for medium‐ to high‐temperature waste heat recovery. Furthermore, thermodynamic calculations and density functional theory (DFT) simulations provided insights into the formation mechanism of Cu 2 Te and the thermoelectric behaviour of BT. This work introduces an efficient, scalable, and environmentally responsible pathway for developing copper‐based thermoelectric materials using industrially relevant precursors.
- 27 August 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (42) , 21333-21346
Pyrite–bismuth telluride heterojunction for hybrid electromagnetic-to-thermoelectric energy harvesting
The FeS 2 /Bi 2 Te 3 heterostructure RF–thermoelectric device, where RF absorption at the Ti/FeS 2 Schottky interface induces localized heating that is converted into electrical power by Bi 2 Te 3 .
- 27 August 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (42) , 21333-21346
Pyrite–bismuth telluride heterojunction for hybrid electromagnetic-to-thermoelectric energy harvesting
The FeS 2 /Bi 2 Te 3 heterostructure RF–thermoelectric device, where RF absorption at the Ti/FeS 2 Schottky interface induces localized heating that is converted into electrical power by Bi 2 Te 3 .
Enhanced Heat Dissipation and Reduced Power Consumption in Electronics Using 2D Hexagonal Boron Nitride
Miniaturization of electronic components has led to overheating, increased power consumption, and early circuit failures. Conventional heat dissipation methods are becoming inadequate due to limited surface area and higher short‐circuit risks. This study presents a fast, low‐cost, and scalable technique using 2D hexagonal boron nitride (hBN) coatings to enhance heat dissipation in commercial electronics. Inexpensive hBN layers, applied by drop casting or spray coating, boost thermal conductivity at IC surfaces from below 0.3 to 260 W m −1 K −1 , resulting in over double the heat flux and convective heat transfer. This significantly reduces operating temperatures and power consumption, as demonstrated by a 17.4% reduction in a coated audio amplifier circuit board. Density functional theory indicates enhanced interaction between 2D hBN and packaging materials as a key factor. This approach promises substantial energy and cost savings for large‐scale electronics without altering existing manufacturing processes.
Enhanced Heat Dissipation and Reduced Power Consumption in Electronics Using 2D Hexagonal Boron Nitride
Miniaturization of electronic components has led to overheating, increased power consumption, and early circuit failures. Conventional heat dissipation methods are becoming inadequate due to limited surface area and higher short‐circuit risks. This study presents a fast, low‐cost, and scalable technique using 2D hexagonal boron nitride (hBN) coatings to enhance heat dissipation in commercial electronics. Inexpensive hBN layers, applied by drop casting or spray coating, boost thermal conductivity at IC surfaces from below 0.3 to 260 W m −1 K −1 , resulting in over double the heat flux and convective heat transfer. This significantly reduces operating temperatures and power consumption, as demonstrated by a 17.4% reduction in a coated audio amplifier circuit board. Density functional theory indicates enhanced interaction between 2D hBN and packaging materials as a key factor. This approach promises substantial energy and cost savings for large‐scale electronics without altering existing manufacturing processes.
- 5 June 2025
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 207
Understanding the interface-driven thermoelectric behaviour of Bi2Te3–Ga2Te3 alloys
- 5 June 2025
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 207
Understanding the interface-driven thermoelectric behaviour of Bi2Te3–Ga2Te3 alloys
- Open Access
Pyrite Bismuth Telluride Heterojunction for Hybrid Electromagnetic to Thermoelectric Energy Harvesting
The rapid proliferation of wireless networks and connected devices has led to pervasive electromagnetic (EM) energy dissipation into the environment, an underutilized resource for energy harvesting. Here, we demonstrate a pyrite (FeS$_2$)-bismuth telluride (Bi$_2$Te$_3$) heterojunction that enables hybrid electromagnetic-to-thermoelectric energy conversion. Fabricated via a simple cold-press compaction of powders, the heterojunction forms a Schottky interface at FeS$_2$, facilitating efficient RF absorption and localized heating. This heat is harvested by Bi$_2$Te$_3$ through thermoelectric conversion. Under 35~MHz RF irradiation at 1~W input power, the device achieved a local temperature rise of 46~$^\circ$C and a thermal gradient of 5.5~K across the Bi$_2$Te$_3$, resulting in a peak power density of approximately 13~mW/cm$^2$. Molecular dynamics (MD) simulations and density functional theory (DFT) calculations further elucidate the heat transport behavior and interfacial thermoelectric performance. This work introduces a new class of heterostructures for RF-responsive energy harvesting, offering a scalable route toward self-powered IoT and wireless sensing systems.
Open AccessPyrite Bismuth Telluride Heterojunction for Hybrid Electromagnetic to Thermoelectric Energy Harvesting
The rapid proliferation of wireless networks and connected devices has led to pervasive electromagnetic (EM) energy dissipation into the environment, an underutilized resource for energy harvesting. Here, we demonstrate a pyrite (FeS$_2$)-bismuth telluride (Bi$_2$Te$_3$) heterojunction that enables hybrid electromagnetic-to-thermoelectric energy conversion. Fabricated via a simple cold-press compaction of powders, the heterojunction forms a Schottky interface at FeS$_2$, facilitating efficient RF absorption and localized heating. This heat is harvested by Bi$_2$Te$_3$ through thermoelectric conversion. Under 35~MHz RF irradiation at 1~W input power, the device achieved a local temperature rise of 46~$^\circ$C and a thermal gradient of 5.5~K across the Bi$_2$Te$_3$, resulting in a peak power density of approximately 13~mW/cm$^2$. Molecular dynamics (MD) simulations and density functional theory (DFT) calculations further elucidate the heat transport behavior and interfacial thermoelectric performance. This work introduces a new class of heterostructures for RF-responsive energy harvesting, offering a scalable route toward self-powered IoT and wireless sensing systems.
- Open Access
Localized Radiofrequency Heating for Enhanced Thermoelectric Energy Generation Using Natural Galena Ore
The efficiency of thermoelectric devices can be significantly enhanced by maintaining a stable temperature gradient, which can be achieved through localized heating. Radio waves serve as an ideal heat source for this purpose. In this study, we demonstrate the enhancement of thermoelectric performance in earth-abundant natural ore Galena (PbS) through localized radio frequency (RF) heating. RF heating experiments conducted at frequencies between \SI{35}{MHz} and \SI{45}{MHz} induced substantial localized heating in PbS, generating a temperature gradient of \SI{32}{K}. This resulted in a Seebeck voltage of \SI{-5.8}{mV/K}, approximately 13 times greater than the conventional Seebeck coefficient of PbS (\SI{440}{\micro V/K}). Additionally, a power factor of \SI{151}{mWm^{-1}K^{-2}} and an overall RF to thermoelectric conversion efficiency of 15\% were achieved. Molecular dynamics simulations corroborate the experimental findings, providing insights into the mechanism of thermal transport and RF-induced heating in PbS. These results highlight the potential of localized RF heating as an effective strategy for enhancing thermoelectric performance, with promising implications for ambient thermoelectric energy harvesting applications.
Open AccessLocalized Radiofrequency Heating for Enhanced Thermoelectric Energy Generation Using Natural Galena Ore
The efficiency of thermoelectric devices can be significantly enhanced by maintaining a stable temperature gradient, which can be achieved through localized heating. Radio waves serve as an ideal heat source for this purpose. In this study, we demonstrate the enhancement of thermoelectric performance in earth-abundant natural ore Galena (PbS) through localized radio frequency (RF) heating. RF heating experiments conducted at frequencies between \SI{35}{MHz} and \SI{45}{MHz} induced substantial localized heating in PbS, generating a temperature gradient of \SI{32}{K}. This resulted in a Seebeck voltage of \SI{-5.8}{mV/K}, approximately 13 times greater than the conventional Seebeck coefficient of PbS (\SI{440}{\micro V/K}). Additionally, a power factor of \SI{151}{mWm^{-1}K^{-2}} and an overall RF to thermoelectric conversion efficiency of 15\% were achieved. Molecular dynamics simulations corroborate the experimental findings, providing insights into the mechanism of thermal transport and RF-induced heating in PbS. These results highlight the potential of localized RF heating as an effective strategy for enhancing thermoelectric performance, with promising implications for ambient thermoelectric energy harvesting applications.
- 5 February 2025
- Published by Wiley in Small Methods
- Vol. 9 (7) , e2402066
Enhanced Non‐Invasive Radio Frequency Heating Using 2D Pyrite (Pyritene)
Radiofrequency (RF) heating is a new, less invasive alternative to invasive heating methods that use nanoparticles for tumour therapy. But pinpoint local heating is still hard. Molecular interactions form a hybrid structure with unique electrical characteristics that enable RF heating in this work, which explores RF heating in a biological cell (yeast)‐2D FeS2 system. Substantial processes have been uncovered via experimental investigations and density functional theory (DFT) computations. At 3 W and 50 MHz, RF heating reaches 54°C in 40 s, which is enough to kill yeast cells, while current‐voltage measurements reveal ionic diode‐like properties. Interactions between yeast lipid molecules and 2D FeSk, as shown by density‐functional theory calculations, cause an imbalance in the distribution of charges and the creation of polar, conductive channels. Insights into biological heating applications based on radio frequency (RF) technology are offered by this work, which lays forth a framework for investigating 2D material‐biomolecule interactions.
- 5 February 2025
- Published by Wiley in Small Methods
- Vol. 9 (7) , e2402066
Enhanced Non‐Invasive Radio Frequency Heating Using 2D Pyrite (Pyritene)
Radiofrequency (RF) heating is a new, less invasive alternative to invasive heating methods that use nanoparticles for tumour therapy. But pinpoint local heating is still hard. Molecular interactions form a hybrid structure with unique electrical characteristics that enable RF heating in this work, which explores RF heating in a biological cell (yeast)‐2D FeS2 system. Substantial processes have been uncovered via experimental investigations and density functional theory (DFT) computations. At 3 W and 50 MHz, RF heating reaches 54°C in 40 s, which is enough to kill yeast cells, while current‐voltage measurements reveal ionic diode‐like properties. Interactions between yeast lipid molecules and 2D FeSk, as shown by density‐functional theory calculations, cause an imbalance in the distribution of charges and the creation of polar, conductive channels. Insights into biological heating applications based on radio frequency (RF) technology are offered by this work, which lays forth a framework for investigating 2D material‐biomolecule interactions.
- 27 December 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (9) , 095502
Microstructure evolution and thermoelectric behaviour of directionally solidified Bi2Te3–Ga2Te3 eutectic alloy
Thermoelectric (TE) materials are known for efficiently converting thermal to electrical energy, and vice versa. Multiphase TEs offer better freedom to tune the TE properties of such materials by varying individual phase fractions, microstructural morphology, interface density controls, etc. These controlled changes in microstructural features can be achieved by directional solidification. Bi2Te3-Ga2Te3 based TEs have been reported with enhanced TE performance. In the present study, alloys with a combination of these phases were developed using a eutectic composition from the pseudo-binary phase diagram of Bi2Te3–Ga2Te3. The alloys were fabricated using the vertical Bridgman method with three different solidification velocities (V), namely 1000 (E1), 200 (E2) and 10 (E3) μm s−1, at a constant temperature gradient of 35 K cm−1 at the solid/liquid interface. Microstructural features show a significant change in the morphology and the interlamellar spacing between two adjacent Ga2Te3 lamellae in alloys E1, E2 and E3. In addition, x-ray diffraction patterns suggest changes in the lattice parameters of Bi2Te3 and Ga2Te3 for all alloys. Significant change in the macrotexture of the different alloys was observed along the growth direction. The highest power factor of 1.6 mW mK−2 was recorded for alloy E2 at room temperature. Alloy E2 shows the highest figure of merit among all the alloys investigated (0.38 at room temperature), attributed to the highest S value of 201.7 μV K−1 at room temperature. In addition, the total thermal conductivity of all alloys was around 1.33 W mK−1 at 307 K, while alloy E1 has the smallest lattice and bipolar thermal conductivity.
- 27 December 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (9) , 095502
Microstructure evolution and thermoelectric behaviour of directionally solidified Bi2Te3–Ga2Te3 eutectic alloy
Thermoelectric (TE) materials are known for efficiently converting thermal to electrical energy, and vice versa. Multiphase TEs offer better freedom to tune the TE properties of such materials by varying individual phase fractions, microstructural morphology, interface density controls, etc. These controlled changes in microstructural features can be achieved by directional solidification. Bi2Te3-Ga2Te3 based TEs have been reported with enhanced TE performance. In the present study, alloys with a combination of these phases were developed using a eutectic composition from the pseudo-binary phase diagram of Bi2Te3–Ga2Te3. The alloys were fabricated using the vertical Bridgman method with three different solidification velocities (V), namely 1000 (E1), 200 (E2) and 10 (E3) μm s−1, at a constant temperature gradient of 35 K cm−1 at the solid/liquid interface. Microstructural features show a significant change in the morphology and the interlamellar spacing between two adjacent Ga2Te3 lamellae in alloys E1, E2 and E3. In addition, x-ray diffraction patterns suggest changes in the lattice parameters of Bi2Te3 and Ga2Te3 for all alloys. Significant change in the macrotexture of the different alloys was observed along the growth direction. The highest power factor of 1.6 mW mK−2 was recorded for alloy E2 at room temperature. Alloy E2 shows the highest figure of merit among all the alloys investigated (0.38 at room temperature), attributed to the highest S value of 201.7 μV K−1 at room temperature. In addition, the total thermal conductivity of all alloys was around 1.33 W mK−1 at 307 K, while alloy E1 has the smallest lattice and bipolar thermal conductivity.
- 6 December 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (3) , 1348-1360
Enhanced thermoelectric performance of sustainable earth-abundant two-dimensional Galena (PbS)
- 6 December 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (3) , 1348-1360
Enhanced thermoelectric performance of sustainable earth-abundant two-dimensional Galena (PbS)