Karl Rönnby
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Karl Rönnby has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Michael Nolan
Tyndall National Institute, University College Cork, Lee Maltings, Dyke Parade, Cork T12R5CP, Ireland
13 shared publications - Henrik Pedersen
Department of Physics, Chemistry and Biology, Linköping University , SE-581 83 Linköping
10 shared publications - Lars Ojamäe
Linköping University
10 shared publications - Anjana Devi
Leibniz Institute for Solid State and Materials Research
5 shared publications - Polla Rouf
Department of Physics, Chemistry and Biology, Linköping University, SE-581 83 Linköping, Sweden
4 shared publications - Detlef Rogalla
RUBION Ruhr University Bochum Bochum Germany
3 shared publications
Latest Publications
- Open Access
- 23 February 2026
- Published by Elsevier in SSRN Electronic Journal
Gold/Gold Oxide as a Solid State On-Chip pH Sensing Probe for Food Applications
In this work we investigate Gold/gold oxide as a solid-state ultra-micro pH sensor for monitoring of different foods which are, typically between 3.5-7 in pH. Using cyclic voltammetry, a linear shift in the gold oxide reduction peak voltage was observed, in response to changes in pH of a solution in which the sensor is submerged. The sensor also has very low sample volume requirements down to ~100 µL. Sensors gave a super-Nernstian response of -67.7 mV/pH in the pH range of pH 3 to pH 7 with an accuracy of <0.02 of pH units. Their high sensitivity, low hysteresis and minimal effect by common interferents demonstrate that these electrodes can be utilised as pH sensors for real world application. A maximum deviation of 0.29 pH units between the developed metal-oxide pH sensor and a conventional glass electrode indicates good usability for beverage samples.
- 23 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessGold/Gold Oxide as a Solid State On-Chip pH Sensing Probe for Food Applications
In this work we investigate Gold/gold oxide as a solid-state ultra-micro pH sensor for monitoring of different foods which are, typically between 3.5-7 in pH. Using cyclic voltammetry, a linear shift in the gold oxide reduction peak voltage was observed, in response to changes in pH of a solution in which the sensor is submerged. The sensor also has very low sample volume requirements down to ~100 µL. Sensors gave a super-Nernstian response of -67.7 mV/pH in the pH range of pH 3 to pH 7 with an accuracy of <0.02 of pH units. Their high sensitivity, low hysteresis and minimal effect by common interferents demonstrate that these electrodes can be utilised as pH sensors for real world application. A maximum deviation of 0.29 pH units between the developed metal-oxide pH sensor and a conventional glass electrode indicates good usability for beverage samples.
- Open Access
A Liquid Ge(IV) Precursor for Low Temperature Plasma Enhanced Atomic Layer Deposition of Germanium Oxide Thin Films
Germanium oxide thin films are promising for advanced applications such as microelectronics, optoelectronics, high‐power electronics, optics, and biomedical uses. However, scalable and controlled low‐temperature synthesis of GeO 2 thin films via atomic layer deposition (ALD) is limited by the small range of available Ge precursors. We introduce monomeric tetrakis‐3‐( N , N ‐dimethylamino)propyl germanium(IV) [Ge(DMP) 4 ] as a promising Ge precursor. It is non‐pyrophoric, thermally stable, and liquid, and can be obtained in high purity on a multigram scale through an industrially feasible synthesis. Using density functional theory (DFT) and mass spectrometry (MS), we rationalize the coordination environment and identify a feasible chemisorption pathway, indicating a high reactivity of the precursor. Subsequently, [Ge(DMP) 4 ] was employed in low‐temperature plasma‐enhanced ALD (PEALD) over a wide temperature range from 40°C to 240°C, yielding smooth, uniform germanium oxide films. Rapid and homogeneous nucleation leads to dense films with sub‐nanometer thickness. By adjusting the deposition temperature and plasma duration, the film composition could be readily tuned from GeO 2 to sub‐stoichiometric GeO x . These findings establish [Ge(DMP) 4 ] as an effective, scalable precursor for low‐temperature ALD of GeO 2 , emphasizing the critical role of precursor chemistry in ALD process development.
Open AccessA Liquid Ge(IV) Precursor for Low Temperature Plasma Enhanced Atomic Layer Deposition of Germanium Oxide Thin Films
Germanium oxide thin films are promising for advanced applications such as microelectronics, optoelectronics, high‐power electronics, optics, and biomedical uses. However, scalable and controlled low‐temperature synthesis of GeO 2 thin films via atomic layer deposition (ALD) is limited by the small range of available Ge precursors. We introduce monomeric tetrakis‐3‐( N , N ‐dimethylamino)propyl germanium(IV) [Ge(DMP) 4 ] as a promising Ge precursor. It is non‐pyrophoric, thermally stable, and liquid, and can be obtained in high purity on a multigram scale through an industrially feasible synthesis. Using density functional theory (DFT) and mass spectrometry (MS), we rationalize the coordination environment and identify a feasible chemisorption pathway, indicating a high reactivity of the precursor. Subsequently, [Ge(DMP) 4 ] was employed in low‐temperature plasma‐enhanced ALD (PEALD) over a wide temperature range from 40°C to 240°C, yielding smooth, uniform germanium oxide films. Rapid and homogeneous nucleation leads to dense films with sub‐nanometer thickness. By adjusting the deposition temperature and plasma duration, the film composition could be readily tuned from GeO 2 to sub‐stoichiometric GeO x . These findings establish [Ge(DMP) 4 ] as an effective, scalable precursor for low‐temperature ALD of GeO 2 , emphasizing the critical role of precursor chemistry in ALD process development.
- Open Access
- 31 October 2025
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 54 (47) , 17507-17520
Plasma-enhanced atomic layer deposition of AlPO 4 /AlP x O y : comparing dual source and supercycle approaches for composition control
Two plasma-enhanced atomic layer deposition (PEALD) pathways for AlP x O y thin films are compared: a dual-source process with a new TMA-phosphine adduct yields P-doped Al 2 O 3 , and a supercycle approach using P(NMe 2 ) 3 and TMA results in tunable AlPO 4 .
- 31 October 2025
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 54 (47) , 17507-17520
Open AccessPlasma-enhanced atomic layer deposition of AlPO 4 /AlP x O y : comparing dual source and supercycle approaches for composition control
Two plasma-enhanced atomic layer deposition (PEALD) pathways for AlP x O y thin films are compared: a dual-source process with a new TMA-phosphine adduct yields P-doped Al 2 O 3 , and a supercycle approach using P(NMe 2 ) 3 and TMA results in tunable AlPO 4 .
- Open Access
- 26 September 2025
- Published by Wiley in Advanced Materials Interfaces
- Vol. 12 (21)
Control of Copper Morphology on TaN through Surface Point Defects
The downscaling of semiconductor devices makes deposition of copper interconnects challenging. Copper forms non‐conductive islands on diffusion barriers such as TaN and this effect worsens as length scales move toward the few‐nm. Adding a liner or glue layer, doping the substrate to achieve better adhesion or replacing Cu are being investigated to overcome this challenge. Introducing surface defects, e.g. surface point defects or dopants, can modify the metal nucleation and promote growth of targeted morphologies. Density functional theory (DFT) and ab initio molecular dynamics (aiMD) are used to model surface point defects in TaN and explore how these surface defects can control the adsorption and morphology preference of deposited Cu nanostructures. Formation of nitrogen vacancies is favorable, especially in a hydrogen ambient, with small energy cost, indicating possible control of defects through control of atmosphere during processing. Combining adsorption studies of single atoms and small metal clusters with aiMD simulations of larger metal structures, we show how higher concentrations of surface nitrogen vacancies may limit undesired 3D growth, while a low concentration of vacancies has a negligible effect, promoting 3D island morphology. These results show that morphology control by surface defects is a way to promote target metal morphology.
- 26 September 2025
- Published by Wiley in Advanced Materials Interfaces
- Vol. 12 (21)
Open AccessControl of Copper Morphology on TaN through Surface Point Defects
The downscaling of semiconductor devices makes deposition of copper interconnects challenging. Copper forms non‐conductive islands on diffusion barriers such as TaN and this effect worsens as length scales move toward the few‐nm. Adding a liner or glue layer, doping the substrate to achieve better adhesion or replacing Cu are being investigated to overcome this challenge. Introducing surface defects, e.g. surface point defects or dopants, can modify the metal nucleation and promote growth of targeted morphologies. Density functional theory (DFT) and ab initio molecular dynamics (aiMD) are used to model surface point defects in TaN and explore how these surface defects can control the adsorption and morphology preference of deposited Cu nanostructures. Formation of nitrogen vacancies is favorable, especially in a hydrogen ambient, with small energy cost, indicating possible control of defects through control of atmosphere during processing. Combining adsorption studies of single atoms and small metal clusters with aiMD simulations of larger metal structures, we show how higher concentrations of surface nitrogen vacancies may limit undesired 3D growth, while a low concentration of vacancies has a negligible effect, promoting 3D island morphology. These results show that morphology control by surface defects is a way to promote target metal morphology.
- Open Access
- 23 September 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Gold/Gold Oxide as a Solid State On-Chip pH Sensing Probe
In this work we investigate Gold/gold oxide as a solid-state ultra-micro pH sensor for monitoring of different liquids including real-world samples such as commercially available beverages. A shift in the gold oxide reduction peak voltage was observed, based on the pH of the solution in which the sensor is submerged. The sensor also has very low sample volumes down to ~100 µL. Sensors gave a super-Nernstian response of -67.7 mV/pH in the pH range of pH 3 to pH 7 with an accuracy of <0.02 of pH units. Their high sensitivity, low hysteresis and minimal effect by common interferents demonstrate that these electrodes can be utilised as pH sensors for real world application. A maximum deviation of 0.29 pH units between the developed metal-oxide pH sensor and a conventional glass electrode indicates good usability.
- 23 September 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessGold/Gold Oxide as a Solid State On-Chip pH Sensing Probe
In this work we investigate Gold/gold oxide as a solid-state ultra-micro pH sensor for monitoring of different liquids including real-world samples such as commercially available beverages. A shift in the gold oxide reduction peak voltage was observed, based on the pH of the solution in which the sensor is submerged. The sensor also has very low sample volumes down to ~100 µL. Sensors gave a super-Nernstian response of -67.7 mV/pH in the pH range of pH 3 to pH 7 with an accuracy of <0.02 of pH units. Their high sensitivity, low hysteresis and minimal effect by common interferents demonstrate that these electrodes can be utilised as pH sensors for real world application. A maximum deviation of 0.29 pH units between the developed metal-oxide pH sensor and a conventional glass electrode indicates good usability.
- Open Access
- 14 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 7 (18) , 12707-12719
On the Differences in Trimethylaluminum Infiltration into PMMA and PLA Polymers for Sequential Infiltration Synthesis: Insights from Experiments and First-Principles Simulations
Sequential infiltration synthesis (SIS) is a powerful approach for templated growth of solid materials, such as oxides or metals, that exploits the difference in interaction of a precursor molecule with a polymer or block copolymer. While there have been studies showing that infiltration of trimethyl-aluminum (TMA) in polymers can be used to grow Al2O3, there are still many atomic level details of the SIS process that require more investigation, including the origin of the differences in infiltration of TMA into different polymers. In this paper, we investigated in detail the infiltration of Al2O3 into poly(methyl methacrylate) (PMMA) and poly(lactic acid) (PLA) experimentally and theoretically. SIS was performed in a standard ALD reactor, operating at 70 °C in quasi-static mode, using TMA and water as the metal and oxygen precursors, respectively. Operando spectroscopic ellipsometry and ex-situ X-ray photoelectron spectroscopy (XPS) evidenced that Al2O3 incorporation in PLA is significantly higher than in PMMA even if, in both cases, TMA incorporation occurs through the formation of an Al–O covalent bond at the C–O–C group. The extent of swelling of the polymers upon TMA infiltration is assessed and is clearly larger for TMA in PLA than in PMMA. First-principles density functional theory (DFT) calculations highlighted that both polymers display swelling upon TMA infiltration, saturating with increasing TMA, consistent with operando ellipsometry observations. The DFT results also show the origin of the larger swelling in PLA compared to TMA. Changes in vibrational modes of carbonyl backbone groups in the polymers are used to demonstrate TMA-polymer interactions from both experiment and simulation. The differences in TMA infiltration and swelling arise from differences in the TMA-polymer C–O–C group interaction, which is more exothermic in PLA than in PMMA, in agreement with experimental results. The combination of experimental and theoretical studies herein reported provides a toolkit to disclose the complexities of SIS at the molecular level.
- 14 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 7 (18) , 12707-12719
Open AccessOn the Differences in Trimethylaluminum Infiltration into PMMA and PLA Polymers for Sequential Infiltration Synthesis: Insights from Experiments and First-Principles Simulations
Sequential infiltration synthesis (SIS) is a powerful approach for templated growth of solid materials, such as oxides or metals, that exploits the difference in interaction of a precursor molecule with a polymer or block copolymer. While there have been studies showing that infiltration of trimethyl-aluminum (TMA) in polymers can be used to grow Al2O3, there are still many atomic level details of the SIS process that require more investigation, including the origin of the differences in infiltration of TMA into different polymers. In this paper, we investigated in detail the infiltration of Al2O3 into poly(methyl methacrylate) (PMMA) and poly(lactic acid) (PLA) experimentally and theoretically. SIS was performed in a standard ALD reactor, operating at 70 °C in quasi-static mode, using TMA and water as the metal and oxygen precursors, respectively. Operando spectroscopic ellipsometry and ex-situ X-ray photoelectron spectroscopy (XPS) evidenced that Al2O3 incorporation in PLA is significantly higher than in PMMA even if, in both cases, TMA incorporation occurs through the formation of an Al–O covalent bond at the C–O–C group. The extent of swelling of the polymers upon TMA infiltration is assessed and is clearly larger for TMA in PLA than in PMMA. First-principles density functional theory (DFT) calculations highlighted that both polymers display swelling upon TMA infiltration, saturating with increasing TMA, consistent with operando ellipsometry observations. The DFT results also show the origin of the larger swelling in PLA compared to TMA. Changes in vibrational modes of carbonyl backbone groups in the polymers are used to demonstrate TMA-polymer interactions from both experiment and simulation. The differences in TMA infiltration and swelling arise from differences in the TMA-polymer C–O–C group interaction, which is more exothermic in PLA than in PMMA, in agreement with experimental results. The combination of experimental and theoretical studies herein reported provides a toolkit to disclose the complexities of SIS at the molecular level.
- Open Access
- 4 September 2025
- Published by Wiley in Angewandte Chemie
- Vol. 137 (47)
Ein seltener mononuklearer Lithium‐Carben‐Komplex für die Atomlagenabscheidung von lithiumhaltigen Dünnschichten
Kurzfassung: Lithium ist das zentrale Element moderner Batterietechnologien, und die Herstellung von lithiumhaltigen Materialien mittels Atomlagenabscheidung (engl. Atomic Layer Deposition, ALD) bietet erhebliche Vorteile bei der Kontrolle der Schichtdicke und ‐zusammensetzung. In dieser Studie wird ein neuer mononuklearer, durch ein N‐heterocyclisches Carben (NHC) stabilisierter Lithiumkomplex, [Li( tBu NHC)(hmds)], als vielversprechender Präkursor für die ALD von lithiumhaltigen Dünnschichten vorgestellt. Die strukturelle Charakterisierung erfolgt durch den Vergleich von Dichtefunktionaltheorie (DFT) und Einkristall‐Röntgenbeugung (engl. Single‐Crystal X‐ray Diffraction, SC‐XRD), wobei die seltene mononukleare Struktur bestätigt wird. Thermogravimetrische Analysen (TGA) zeigen vorteilhafte thermische Eigenschaften für ALD‐Anwendungen. Die Verbindung weist einen niedrigen Schmelzpunkt, saubere Verdampfung und ermutigende Volatilitätsparameter im Vergleich zu anderen Lithium‐Präkursoren auf. ALD‐Experimente mit [Li( tBu NHC)(hmds)] und Ozon zeigen dessen Effektivität bei der Abscheidung von LiSi x O y ‐Filmen. Der ALD‐Prozess zeigt ein gesättigtes Wachstum pro Zyklus (engl. Growth per Cycle, GPC) von 0,95 Å. Die Zusammensetzung, analysiert mittels Rutherford‐Rückstreu‐Spektrometrie/Kernreaktionsanalyse (engl. Rutherford Backscattering Spectrometry/Nuclear Reaction Analysis, RBS/NRA), Röntgenphotoelektronenspektroskopie (engl. X‐ray Photoelectron Spectroscopy, XPS) und Glimmentladungsspektroskopie (engl. Glow Discharge Optical Emission Spectrometry, GD‐OES), bestätigt das Vorhandensein von Lithium und Silizium in den erwarteten Verhältnissen. Diese Arbeit stellt nicht nur einen neuen ALD‐Präkursor vor, sondern trägt auch zum Verständnis der Lithiumchemie bei und bietet Einblicke in die faszinierende Koordinationschemie und das thermische Verhalten von durch NHC‐Liganden stabilisierten Lithiumkomplexen.
- 4 September 2025
- Published by Wiley in Angewandte Chemie
- Vol. 137 (47)
Open AccessEin seltener mononuklearer Lithium‐Carben‐Komplex für die Atomlagenabscheidung von lithiumhaltigen Dünnschichten
Kurzfassung: Lithium ist das zentrale Element moderner Batterietechnologien, und die Herstellung von lithiumhaltigen Materialien mittels Atomlagenabscheidung (engl. Atomic Layer Deposition, ALD) bietet erhebliche Vorteile bei der Kontrolle der Schichtdicke und ‐zusammensetzung. In dieser Studie wird ein neuer mononuklearer, durch ein N‐heterocyclisches Carben (NHC) stabilisierter Lithiumkomplex, [Li( tBu NHC)(hmds)], als vielversprechender Präkursor für die ALD von lithiumhaltigen Dünnschichten vorgestellt. Die strukturelle Charakterisierung erfolgt durch den Vergleich von Dichtefunktionaltheorie (DFT) und Einkristall‐Röntgenbeugung (engl. Single‐Crystal X‐ray Diffraction, SC‐XRD), wobei die seltene mononukleare Struktur bestätigt wird. Thermogravimetrische Analysen (TGA) zeigen vorteilhafte thermische Eigenschaften für ALD‐Anwendungen. Die Verbindung weist einen niedrigen Schmelzpunkt, saubere Verdampfung und ermutigende Volatilitätsparameter im Vergleich zu anderen Lithium‐Präkursoren auf. ALD‐Experimente mit [Li( tBu NHC)(hmds)] und Ozon zeigen dessen Effektivität bei der Abscheidung von LiSi x O y ‐Filmen. Der ALD‐Prozess zeigt ein gesättigtes Wachstum pro Zyklus (engl. Growth per Cycle, GPC) von 0,95 Å. Die Zusammensetzung, analysiert mittels Rutherford‐Rückstreu‐Spektrometrie/Kernreaktionsanalyse (engl. Rutherford Backscattering Spectrometry/Nuclear Reaction Analysis, RBS/NRA), Röntgenphotoelektronenspektroskopie (engl. X‐ray Photoelectron Spectroscopy, XPS) und Glimmentladungsspektroskopie (engl. Glow Discharge Optical Emission Spectrometry, GD‐OES), bestätigt das Vorhandensein von Lithium und Silizium in den erwarteten Verhältnissen. Diese Arbeit stellt nicht nur einen neuen ALD‐Präkursor vor, sondern trägt auch zum Verständnis der Lithiumchemie bei und bietet Einblicke in die faszinierende Koordinationschemie und das thermische Verhalten von durch NHC‐Liganden stabilisierten Lithiumkomplexen.
- Open Access
- 4 September 2025
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 64 (47) , e202513066
Rare Mononuclear Lithium–Carbene Complex for Atomic Layer Deposition of Lithium Containing Thin Films
Lithium is the core material of modern battery technologies and fabricating the lithium‐containing materials with atomic layer deposition (ALD) confers significant benefits in control of film composition and thickness. In this work, a new mononuclear N‐heterocyclic carbene (NHC) stabilized lithium complex, [Li( tBu NHC)(hmds)], is introduced as a promising precursor for ALD of lithium‐containing thin films. Structural characterization is performed, comparing density functional theory (DFT) and single‐crystal X‐ray diffraction (SC‐XRD), confirming a rare mononuclear structure. Favorable thermal properties for ALD applications are evidenced by thermogravimetric analysis (TGA). The compound exhibits a low melting point, clean evaporation, and its volatility parameters are encouraging compared to other lithium precursors. ALD trials using [Li( tBu NHC)(hmds)] with ozone demonstrate its effectiveness in depositing LiSi x O y films. The ALD process exhibits a saturated growth per cycle (GPC) of 0.95 Å. Compositional analysis using Rutherford backscattering spectrometry/nuclear reaction analysis (RBS/NRA), X‐ray photoelectron spectrometry (XPS), and glow discharge optical emission spectrometry (GD‐OES), confirms the presence of lithium and silicon in the expected ratios. This work not only presents a new ALD precursor but also contributes to the understanding of lithium chemistry, offering insights into the intriguing coordination chemistry and thermal behavior of lithium complexes stabilized by NHC ligands.
- 4 September 2025
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 64 (47) , e202513066
Open AccessRare Mononuclear Lithium–Carbene Complex for Atomic Layer Deposition of Lithium Containing Thin Films
Lithium is the core material of modern battery technologies and fabricating the lithium‐containing materials with atomic layer deposition (ALD) confers significant benefits in control of film composition and thickness. In this work, a new mononuclear N‐heterocyclic carbene (NHC) stabilized lithium complex, [Li( tBu NHC)(hmds)], is introduced as a promising precursor for ALD of lithium‐containing thin films. Structural characterization is performed, comparing density functional theory (DFT) and single‐crystal X‐ray diffraction (SC‐XRD), confirming a rare mononuclear structure. Favorable thermal properties for ALD applications are evidenced by thermogravimetric analysis (TGA). The compound exhibits a low melting point, clean evaporation, and its volatility parameters are encouraging compared to other lithium precursors. ALD trials using [Li( tBu NHC)(hmds)] with ozone demonstrate its effectiveness in depositing LiSi x O y films. The ALD process exhibits a saturated growth per cycle (GPC) of 0.95 Å. Compositional analysis using Rutherford backscattering spectrometry/nuclear reaction analysis (RBS/NRA), X‐ray photoelectron spectrometry (XPS), and glow discharge optical emission spectrometry (GD‐OES), confirms the presence of lithium and silicon in the expected ratios. This work not only presents a new ALD precursor but also contributes to the understanding of lithium chemistry, offering insights into the intriguing coordination chemistry and thermal behavior of lithium complexes stabilized by NHC ligands.
- 25 August 2025
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 147 (35) , 31764-31778
Near Room-Temperature Atomic Layer Deposition of Magnesium Oxide Using Bis-3-(N,N-dimethylamino)propyl Magnesium(II) and Water
Magnesium(II) oxide (MgO) is a versatile material that is appealing for a wide range of applications including electronics and biocompatible coatings, as pharmaceutics, and gas barrier layers (GBLs). The growth of MgO films at low temperatures is required for these applications which can be enabled by atomic layer deposition (ALD). However, the chemistry of ALD precursors reported to date for MgO is limited and there are no suitable chemistries for low temperature deposition on sensitive substrates. In this work, we describe the ALD of MgO thin films close to room temperature which was triggered by the use of a new nonpyrophoric Mg precursor that possesses all the prerequisites needed for low temperature ALD. The highly volatile bis-3-(N,N-dimethylamino)propyl magnesium(II) [Mg(DMP)2] precursor is reactive toward water. The unique chemistry of the DMP ligand facilitates the ALD process in a broad temperature range (30-260 °C) with high growth per cycle (GPC) values (2.40 Å at 40 °C and 1.91 Å at 120 °C) on Si substrates and is supported by computational studies. The as deposited films were characterized using complementary tools to investigate the composition, structure and surface topology. Furthermore, we demonstrate the growth of MgO on poly(ethylene terephthalate) (PET) foils that can be exploited for implementation in temperature sensitive flexible devices by low temperature ALD. This work highlights the key role of the DMP ligand in developing a new Mg precursor promoting low temperature ALD of MgO thin films, opening the field of flexible electronics and new applications beyond semiconductor devices.
- 25 August 2025
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 147 (35) , 31764-31778
Near Room-Temperature Atomic Layer Deposition of Magnesium Oxide Using Bis-3-(N,N-dimethylamino)propyl Magnesium(II) and Water
Magnesium(II) oxide (MgO) is a versatile material that is appealing for a wide range of applications including electronics and biocompatible coatings, as pharmaceutics, and gas barrier layers (GBLs). The growth of MgO films at low temperatures is required for these applications which can be enabled by atomic layer deposition (ALD). However, the chemistry of ALD precursors reported to date for MgO is limited and there are no suitable chemistries for low temperature deposition on sensitive substrates. In this work, we describe the ALD of MgO thin films close to room temperature which was triggered by the use of a new nonpyrophoric Mg precursor that possesses all the prerequisites needed for low temperature ALD. The highly volatile bis-3-(N,N-dimethylamino)propyl magnesium(II) [Mg(DMP)2] precursor is reactive toward water. The unique chemistry of the DMP ligand facilitates the ALD process in a broad temperature range (30-260 °C) with high growth per cycle (GPC) values (2.40 Å at 40 °C and 1.91 Å at 120 °C) on Si substrates and is supported by computational studies. The as deposited films were characterized using complementary tools to investigate the composition, structure and surface topology. Furthermore, we demonstrate the growth of MgO on poly(ethylene terephthalate) (PET) foils that can be exploited for implementation in temperature sensitive flexible devices by low temperature ALD. This work highlights the key role of the DMP ligand in developing a new Mg precursor promoting low temperature ALD of MgO thin films, opening the field of flexible electronics and new applications beyond semiconductor devices.
- Open Access
- 15 July 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Control of Copper Morphology on TaN through Surface Point Defects
The downscaling of semiconductor devices makes deposition of copper interconnects challenging. Copper forms non-conductive islands on diffusion barriers such as TaN and this effect worsens as the length scales move towards the few-nm. Adding a liner or glue layer, doping the substrate to achieve better adhesion or replacing Cu are being investigated to overcome this challenge. Introducing surface defects, e.g. surface point defects or dopants, can modify the metal nucleation and promote growth of targeted morphologies. We use density functional theory (DFT) and ab initio molecular dynamics (aiMD) to model surface point defects in TaN and explore how these surface defects can control the adsorption and morphology preference of deposited Cu nanostructures. Formation of nitrogen vacancies is favourable, especially in a hydrogen ambient, with small energy cost, indicating possible control of defects through control of atmosphere during processing. Combining adsorption studies of single atoms and small metal clusters with aiMD simulations of larger metal structures, we show how higher concentrations of surface nitrogen vacancies may limit undesired 3D growth, while a low concentration of vacancies has a negligible effect, promoting 3D island morphology. These results show that morphology control by surface defects is a way to promote target metal morphology
- 15 July 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessControl of Copper Morphology on TaN through Surface Point Defects
The downscaling of semiconductor devices makes deposition of copper interconnects challenging. Copper forms non-conductive islands on diffusion barriers such as TaN and this effect worsens as the length scales move towards the few-nm. Adding a liner or glue layer, doping the substrate to achieve better adhesion or replacing Cu are being investigated to overcome this challenge. Introducing surface defects, e.g. surface point defects or dopants, can modify the metal nucleation and promote growth of targeted morphologies. We use density functional theory (DFT) and ab initio molecular dynamics (aiMD) to model surface point defects in TaN and explore how these surface defects can control the adsorption and morphology preference of deposited Cu nanostructures. Formation of nitrogen vacancies is favourable, especially in a hydrogen ambient, with small energy cost, indicating possible control of defects through control of atmosphere during processing. Combining adsorption studies of single atoms and small metal clusters with aiMD simulations of larger metal structures, we show how higher concentrations of surface nitrogen vacancies may limit undesired 3D growth, while a low concentration of vacancies has a negligible effect, promoting 3D island morphology. These results show that morphology control by surface defects is a way to promote target metal morphology