Lixian Song
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lixian Song has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Ai Lu
Institute of Chemical Materials, China Academy of Engineering Physics, Mianyang 621900, China
7 shared publications Liang Chen
4 shared publications- Liangbin Li
National Synchrotron Radiation Laboratory, State Key Laboratory of Advanced Glass Materials, Anhui Provincial Engineering Research Center for Advanced Functional Polymer Films, University of Science and Technology of China , Hefei, Anhui 230029
4 shared publications - Zhongyuan Lu
State Key Laboratory of Environment-Friendly Energy Materials, School of Materials and Chemistry, Southwest University of Science and Technology, Mianyang 621010, China
4 shared publications - Quan-Ping Zhang
State Key Laboratory of Environment‐Friendly Energy Materials School of Materials and Chemistry, Southwest University of Science and Technology Mianyang China
3 shared publications Guangai Sun
2 shared publications
Latest Publications
- 1 September 2018
- Published by Elsevier in Composites Science and Technology
- Vol. 165, 373-379
Correlation between mechanical properties and microscopic structures of an optimized silica fraction in silicone rubber
- 1 September 2018
- Published by Elsevier in Composites Science and Technology
- Vol. 165, 373-379
Correlation between mechanical properties and microscopic structures of an optimized silica fraction in silicone rubber
- 6 August 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (23) , 15859-15870
Controlled synthesis of train-structured montmorillonite/layered double hydroxide nanocomposites by regulating the hydrolysis of polylactic acid
- 6 August 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (23) , 15859-15870
Controlled synthesis of train-structured montmorillonite/layered double hydroxide nanocomposites by regulating the hydrolysis of polylactic acid
- 1 October 2017
- Published by Elsevier in Polymer Testing
- Vol. 63, 494-504
Synthesis of the polyethylene glycol solid-solid phase change materials with a functionalized graphene oxide for thermal energy storage
- 1 October 2017
- Published by Elsevier in Polymer Testing
- Vol. 63, 494-504
Synthesis of the polyethylene glycol solid-solid phase change materials with a functionalized graphene oxide for thermal energy storage
- 8 September 2017
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 50 (18) , 7249-7257
Visualizing the Toughening Mechanism of Nanofiller with 3D X-ray Nano-CT: Stress-Induced Phase Separation of Silica Nanofiller and Silicone Polymer Double Networks
- 8 September 2017
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 50 (18) , 7249-7257
Visualizing the Toughening Mechanism of Nanofiller with 3D X-ray Nano-CT: Stress-Induced Phase Separation of Silica Nanofiller and Silicone Polymer Double Networks
- Open Access
- 7 February 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (20)
Solid‐state microcellular high temperature vulcanized (HTV) silicone rubber foam with carbon dioxide
A series of microcellular high temperature vulcanized (HTV) silicone rubber foams were prepared using CO2 as a physical blowing agent. Rheological properties, gas diffusive behavior, and foaming parameters of silicone rubber were investigated. The results show that saturation pressure has a significant effect on the diffusivity of CO2 in HTV silicone rubber matrix. The gas concentration and diffusivity increase from 2.45 wt % to 3.24 wt %, and from 1.62 × 10−5 cm2/s to 7.83 × 10−5 cm2/s as the saturation pressure increases from 2 MPa to 5 MPa, respectively. The value of the gas diffusivity in HTV silicone rubber is almost 1000 times higher than that of the gas diffusivity in polyetherimide (PEI) matrix. Additionally, microcellular HTV silicone rubber foams with the smallest cell diameter of 9.8 μm and cell density exceeding 108 cells/cm3 are achieved. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44807.
- 7 February 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (20)
Open AccessSolid‐state microcellular high temperature vulcanized (HTV) silicone rubber foam with carbon dioxide
A series of microcellular high temperature vulcanized (HTV) silicone rubber foams were prepared using CO2 as a physical blowing agent. Rheological properties, gas diffusive behavior, and foaming parameters of silicone rubber were investigated. The results show that saturation pressure has a significant effect on the diffusivity of CO2 in HTV silicone rubber matrix. The gas concentration and diffusivity increase from 2.45 wt % to 3.24 wt %, and from 1.62 × 10−5 cm2/s to 7.83 × 10−5 cm2/s as the saturation pressure increases from 2 MPa to 5 MPa, respectively. The value of the gas diffusivity in HTV silicone rubber is almost 1000 times higher than that of the gas diffusivity in polyetherimide (PEI) matrix. Additionally, microcellular HTV silicone rubber foams with the smallest cell diameter of 9.8 μm and cell density exceeding 108 cells/cm3 are achieved. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44807.
- 17 October 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (103) , 101470-101476
The effect of bound rubber on vulcanization kinetics in silica filled silicone rubber
Different filler networks mediated by bound rubber show obviously different effects on vulcanization kinetics.
- 17 October 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (103) , 101470-101476
The effect of bound rubber on vulcanization kinetics in silica filled silicone rubber
Different filler networks mediated by bound rubber show obviously different effects on vulcanization kinetics.
- 24 August 2016
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 301 (11) , 1390-1401
From the Volume‐Filling Effect to the Stress‐Bearing Network: The Reinforcement Mechanisms of Carbon Black Filler in Natural Rubber
Using synchrotron‐radiation X‐rays for nanoscale computed tomography (X‐ray nano‐CT), the structure and corresponding reinforcement effects of carbon black (CB) filler at various amounts in natural rubber (NR) are studied during cyclic loading. All structural parameters of the CB filler, which are extracted from X‐ray images—such as the destruction and reconstruction ratios of the aggregates and the network connectivity, show a transition point with the CB content at around 30 phr (phr = parts by weight per hundred parts of rubber). When the CB content is above the transition point, the effective volume fraction exceeds the percolation threshold, and a stress‐bearing filler network can form; this network can effectively transmit the external stress to the entire sample and abruptly enhance the reinforcement factor. Below the percolation threshold, the CB filler is mainly disconnected aggregates, where its reinforcement of the rubber matrix can be mainly described by the volume‐filling effect. Using the dynamic cluster–cluster aggregation (CCA) model, calculations of the mechanical properties related to the CB content suggest that the network structure plays a major role in the reinforcement of the NR. image
- 24 August 2016
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 301 (11) , 1390-1401
From the Volume‐Filling Effect to the Stress‐Bearing Network: The Reinforcement Mechanisms of Carbon Black Filler in Natural Rubber
Using synchrotron‐radiation X‐rays for nanoscale computed tomography (X‐ray nano‐CT), the structure and corresponding reinforcement effects of carbon black (CB) filler at various amounts in natural rubber (NR) are studied during cyclic loading. All structural parameters of the CB filler, which are extracted from X‐ray images—such as the destruction and reconstruction ratios of the aggregates and the network connectivity, show a transition point with the CB content at around 30 phr (phr = parts by weight per hundred parts of rubber). When the CB content is above the transition point, the effective volume fraction exceeds the percolation threshold, and a stress‐bearing filler network can form; this network can effectively transmit the external stress to the entire sample and abruptly enhance the reinforcement factor. Below the percolation threshold, the CB filler is mainly disconnected aggregates, where its reinforcement of the rubber matrix can be mainly described by the volume‐filling effect. Using the dynamic cluster–cluster aggregation (CCA) model, calculations of the mechanical properties related to the CB content suggest that the network structure plays a major role in the reinforcement of the NR. image