Aditya R. Jangid
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aditya R. Jangid has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- E. Brandon Strong
Department of Neurosurgery, University of California, Davis, Sacramento, California
3 shared publications - Nathaniel W. Martinez
Department of Biological Sciences, California Polytechnic State University, San Luis Obispo, CA 93407, USA
3 shared publications - Andres W. Martinez
Chemistry & Biochemistry Department, California Polytechnic State University, San Luis Obispo, California 93407, United States
2 shared publications Andres W. Martinez
Department of Chemistry & Biochemistry, California Polytechnic State University, San Luis Obispo, CA 93407, United States of America
1 shared publication- Brittany A. Lore
Department of Biological Sciences, California Polytechnic State University, San Luis Obispo, CA 93407, USA
1 shared publication - Carsten Knutsen
Department of Biological Sciences, California Polytechnic State University, San Luis Obispo, CA 93407, USA
1 shared publication
Latest Publications
- 1 September 2019
- Published by Elsevier in Journal of Microbiological Methods
- Vol. 164, 105654
Micro-staining microbes: An alternative to traditional staining of microbiological specimens using microliter volumes of reagents
- 1 September 2019
- Published by Elsevier in Journal of Microbiological Methods
- Vol. 164, 105654
Micro-staining microbes: An alternative to traditional staining of microbiological specimens using microliter volumes of reagents
- Open Access
- 21 August 2019
- Published by MDPI AG in Inventions
- Vol. 4 (3) , 48
Chronometric Quantitation of Analytes in Paper-Based Microfluidic Devices (MicroPADs) via Enzymatic Degradation of a Metastable Biomatrix
The following article summarizes United States Patent Application No. US20180052155A1, titled ‘Assay Devices and Methods’ (filed 16 August 2016, published 22 February 2018). While lateral flow assays (LFAs) have revolutionized point-of-care diagnostics by enabling accurate, inexpensive, and rapid detection of biomarkers, they typically do not provide quantitative results. Hence, there is a significant need for quantitative assays at the point of care. This patent summary describes a novel method of chronometric biomarker quantitation via enzymatic degradation of a metastable gelatin-based biomatrix, principally suited for use in paper-based microfluidic devices (microPADs). This new quantitation mechanism was designed to meet the ASSURED criteria for point-of-care diagnostic devices laid forth by the World Health Organization and may ultimately provide increased access to healthcare, at a significantly reduced cost, around the world.
- 21 August 2019
- Published by MDPI AG in Inventions
- Vol. 4 (3) , 48
Open AccessChronometric Quantitation of Analytes in Paper-Based Microfluidic Devices (MicroPADs) via Enzymatic Degradation of a Metastable Biomatrix
The following article summarizes United States Patent Application No. US20180052155A1, titled ‘Assay Devices and Methods’ (filed 16 August 2016, published 22 February 2018). While lateral flow assays (LFAs) have revolutionized point-of-care diagnostics by enabling accurate, inexpensive, and rapid detection of biomarkers, they typically do not provide quantitative results. Hence, there is a significant need for quantitative assays at the point of care. This patent summary describes a novel method of chronometric biomarker quantitation via enzymatic degradation of a metastable gelatin-based biomatrix, principally suited for use in paper-based microfluidic devices (microPADs). This new quantitation mechanism was designed to meet the ASSURED criteria for point-of-care diagnostic devices laid forth by the World Health Organization and may ultimately provide increased access to healthcare, at a significantly reduced cost, around the world.
- Open Access
- 19 March 2019
- Published by MDPI AG in Inventions
- Vol. 4 (1) , 20
Wax-Printed Fluidic Time Delays for Automating Multi-Step Assays in Paper-Based Microfluidic Devices (MicroPADs)
Microfluidic paper-based analytical devices (microPADs) have emerged as a promising platform for point-of-care diagnostic devices. While the inherent wicking properties of microPADs allow for fluid flow without supporting equipment, this also presents a major challenge in achieving robust fluid control, which becomes especially important when performing complex multi-step assays. Herein, we describe an ideal method of fluid control mediated by wax-printed fluidic time delays. This method relies on a simple fabrication technique, does not utilize chemicals/reagents that could affect downstream assays, is readily scalable, and has a wide temporal range of tunable fluid control. The delays are wax printed on both the top and bottom of pre-fabricated microPAD channels, without subsequent heating, to create hemi-/fully-enclosed channels. With these wax printed delays, we were able to tune the time it took aqueous solutions to wick across a 25 mm-long channel between 3.6 min and 13.4 min. We then employed these fluid delays in the sequential delivery of four dyes to a test zone. Additionally, we demonstrated the automation of two simple enzymatic assays with this fluid control modality. This method of fluid control may allow future researchers to automate more complex assays, thereby further advancing microPADs toward real-world applications.
- 19 March 2019
- Published by MDPI AG in Inventions
- Vol. 4 (1) , 20
Open AccessWax-Printed Fluidic Time Delays for Automating Multi-Step Assays in Paper-Based Microfluidic Devices (MicroPADs)
Microfluidic paper-based analytical devices (microPADs) have emerged as a promising platform for point-of-care diagnostic devices. While the inherent wicking properties of microPADs allow for fluid flow without supporting equipment, this also presents a major challenge in achieving robust fluid control, which becomes especially important when performing complex multi-step assays. Herein, we describe an ideal method of fluid control mediated by wax-printed fluidic time delays. This method relies on a simple fabrication technique, does not utilize chemicals/reagents that could affect downstream assays, is readily scalable, and has a wide temporal range of tunable fluid control. The delays are wax printed on both the top and bottom of pre-fabricated microPAD channels, without subsequent heating, to create hemi-/fully-enclosed channels. With these wax printed delays, we were able to tune the time it took aqueous solutions to wick across a 25 mm-long channel between 3.6 min and 13.4 min. We then employed these fluid delays in the sequential delivery of four dyes to a test zone. Additionally, we demonstrated the automation of two simple enzymatic assays with this fluid control modality. This method of fluid control may allow future researchers to automate more complex assays, thereby further advancing microPADs toward real-world applications.