Esben Almkvist
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Esben Almkvist has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Jesper Landmér Pedersen
Klimator AB, Sweden
1 shared publicationJörgen Bogren
Department of Earth Sciences, University of Gothenburg, Gothenburg, Sweden
1 shared publicationMariana Alves David
Klimator AB, Sweden
1 shared publicationRebecca Lewis-Lück
Klimator AB, Sweden
1 shared publicationSweden
1 shared publicationSweden Klimator AB
1 shared publication
Latest Publications
- 28 October 2023
- Published by SAE International in SAE International Journal of Electrified Vehicles
- Vol. 17 (1)
Enhancing Autonomous Vehicle Safety in Cold Climates by Using a Road Weather Model: Safely Avoiding Unnecessary Operational Design Domain Exits
This study investigates the use of a road weather model (RWM) as a virtual sensing technique to assist autonomous vehicles (AVs) in driving safely, even in challenging winter weather conditions. In particular, we investigate how the AVs can remain within their operational design domain (ODD) for a greater duration and minimize unnecessary exits. As the road surface temperature (RST) is one of the most critical variables for driving safety in winter weather, we explore the use of the vehicle’s air temperature (AT) sensor as an indicator of RST. Data from both Road Weather Information System (RWIS) stations and vehicles measuring AT and road conditions were used. Results showed that using only the AT sensor as an indicator of RST could result in a high number of false warnings, but the accuracy improved significantly with the use of an RWM to model the RST. ROC-curve analysis resulted in an AUC value of 0.917 with the AT sensor and 0.985 with the RWM, while the true positive rate increased from 67% to 94%. The study also highlights the limitations of relying on dashboard cameras to detect slippery driving conditions, as it may not be accurate enough to distinguish between, for example, wet and icy road conditions. As winter maintenance often prevents slippery roads, the vehicles often measured wet or moist roads, despite RST < 0°C. Our calculations indicate that the vehicle should be able to detect 93% of slippery occasions but the rate of false warnings will be as high as 73%, if using a dashboard camera along with the AT sensor. There are clear benefits of using a RWM to improve road safety and reduce the risk of accidents due to slippery conditions, allowing AVs to safely extend their time within their ODD. The findings of this study provide valuable insights for the development of AVs and their response to slippery road conditions.
- 28 October 2023
- Published by SAE International in SAE International Journal of Electrified Vehicles
- Vol. 17 (1)
Enhancing Autonomous Vehicle Safety in Cold Climates by Using a Road Weather Model: Safely Avoiding Unnecessary Operational Design Domain Exits
This study investigates the use of a road weather model (RWM) as a virtual sensing technique to assist autonomous vehicles (AVs) in driving safely, even in challenging winter weather conditions. In particular, we investigate how the AVs can remain within their operational design domain (ODD) for a greater duration and minimize unnecessary exits. As the road surface temperature (RST) is one of the most critical variables for driving safety in winter weather, we explore the use of the vehicle’s air temperature (AT) sensor as an indicator of RST. Data from both Road Weather Information System (RWIS) stations and vehicles measuring AT and road conditions were used. Results showed that using only the AT sensor as an indicator of RST could result in a high number of false warnings, but the accuracy improved significantly with the use of an RWM to model the RST. ROC-curve analysis resulted in an AUC value of 0.917 with the AT sensor and 0.985 with the RWM, while the true positive rate increased from 67% to 94%. The study also highlights the limitations of relying on dashboard cameras to detect slippery driving conditions, as it may not be accurate enough to distinguish between, for example, wet and icy road conditions. As winter maintenance often prevents slippery roads, the vehicles often measured wet or moist roads, despite RST < 0°C. Our calculations indicate that the vehicle should be able to detect 93% of slippery occasions but the rate of false warnings will be as high as 73%, if using a dashboard camera along with the AT sensor. There are clear benefits of using a RWM to improve road safety and reduce the risk of accidents due to slippery conditions, allowing AVs to safely extend their time within their ODD. The findings of this study provide valuable insights for the development of AVs and their response to slippery road conditions.
- 1 May 2019
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 58 (5) , 1023-1038
Modeling Road Surface Temperature from Air Temperature and Geographical Parameters—Implication for the Application of Floating Car Data in a Road Weather Forecast Model
Precise forecasts of road surface temperature (RST) and road conditions allow winter roads to be maintained efficiently. The upcoming “big data” application known as “floating car data” (FCD) provides the opportunity to improve road weather forecasts with measurements of air temperature Ta from in-car sensors. The research thus far with regard to thermal mapping has mainly focused on clear and calm nights, which occur rarely and during low traffic intensity. It is expected that more than 99% of the FCD will be collected during conditions other than clear and calm nights. Utilizing 32 runs of thermal mapping and controlled Ta surveys carried out on mostly busy roads over one winter season, it was possible to simulate the use of Ta and geographical parameters to reflect the variation of RST. The results show that the examined route had several repeatable thermal fingerprints during times of relatively high traffic intensity and with different weather patterns. The measurement time, real-time weather pattern, and previous weather patterns influenced the spatial pattern of thermal fingerprints. The influence of urban density and altitude on RST can be partly seen in their relationship with Ta, whereas the influence of shading and sky-view factor was only seen for RST. The regression models with Ta included explained up to 82% of the RST distribution and outperformed models that are based only on the geographical parameters by as much as 30%. The performance of the models denotes the possible utility of Ta from FCD, but further investigation is needed before moving from controlled Ta measurements to Ta from FCD.
- 1 May 2019
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 58 (5) , 1023-1038
Modeling Road Surface Temperature from Air Temperature and Geographical Parameters—Implication for the Application of Floating Car Data in a Road Weather Forecast Model
Precise forecasts of road surface temperature (RST) and road conditions allow winter roads to be maintained efficiently. The upcoming “big data” application known as “floating car data” (FCD) provides the opportunity to improve road weather forecasts with measurements of air temperature Ta from in-car sensors. The research thus far with regard to thermal mapping has mainly focused on clear and calm nights, which occur rarely and during low traffic intensity. It is expected that more than 99% of the FCD will be collected during conditions other than clear and calm nights. Utilizing 32 runs of thermal mapping and controlled Ta surveys carried out on mostly busy roads over one winter season, it was possible to simulate the use of Ta and geographical parameters to reflect the variation of RST. The results show that the examined route had several repeatable thermal fingerprints during times of relatively high traffic intensity and with different weather patterns. The measurement time, real-time weather pattern, and previous weather patterns influenced the spatial pattern of thermal fingerprints. The influence of urban density and altitude on RST can be partly seen in their relationship with Ta, whereas the influence of shading and sky-view factor was only seen for RST. The regression models with Ta included explained up to 82% of the RST distribution and outperformed models that are based only on the geographical parameters by as much as 30%. The performance of the models denotes the possible utility of Ta from FCD, but further investigation is needed before moving from controlled Ta measurements to Ta from FCD.