Mikko Varonen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mikko Varonen has a total of 195 co-authors. Here are the top co-authors by number of shared publications:
Kari A. I. Halonen
Department of Electronics and Nanoengineering, Aalto University, Espoo, Finland
30 shared publications- Dristy Parveg
VTT Technical Research Centre of Finland Ltd., Espoo, Finland
22 shared publications Mikko Karkkainen
Department of Micro and Nanosciences, SMARAD-2, Aalto University, Espoo, Finland
19 shared publicationsPekka Kangaslahti
NASA Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 USA
16 shared publicationsP. Kangaslahti
Jet Propulsion Laboratory California Institute of Technology, Pasadena California USA
15 shared publications- Rodrigo Reeves
CePIA, Astronomy Department, Universidad de Concepción, Casilla 160-C, Concepción, Chile
12 shared publications
Latest Publications
- 13 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 14 (6) , 1007-1014
Cryogenic Characterization of LTCC Material in Millimeter-Wave Frequencies
This study presents room temperature and cryogenic (20 K) characterization of the electrical properties of the Ferro A6M-E material, manufactured using LTCC technology, at W-band (75-110 GHz). The resonant ring method was used to design microstrip structures with resonant frequencies at 80, 90, and 100 GHz on a single substrate. S-parameter measurements at the different physical temperatures were obtained. The relative permittivity and loss tangent parameters were calculated, obtaining values of ε r = 6.14 and tan δ = 0.0019 at 300K and ε r = 6.0 and tan δ = 0.002 for 20 K. The calculated dielectric properties show a small variability between room temperature and cryogenic conditions in the W-band. These results are highly relevant for the understanding of the electrical performance of Ferro A6M-E material, particularly in the context of mm and sub-mm wave applications for front-end radio astronomy receivers and space applications, both at room temperature and cryogenic conditions.
- 13 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 14 (6) , 1007-1014
Cryogenic Characterization of LTCC Material in Millimeter-Wave Frequencies
This study presents room temperature and cryogenic (20 K) characterization of the electrical properties of the Ferro A6M-E material, manufactured using LTCC technology, at W-band (75-110 GHz). The resonant ring method was used to design microstrip structures with resonant frequencies at 80, 90, and 100 GHz on a single substrate. S-parameter measurements at the different physical temperatures were obtained. The relative permittivity and loss tangent parameters were calculated, obtaining values of ε r = 6.14 and tan δ = 0.0019 at 300K and ε r = 6.0 and tan δ = 0.002 for 20 K. The calculated dielectric properties show a small variability between room temperature and cryogenic conditions in the W-band. These results are highly relevant for the understanding of the electrical performance of Ferro A6M-E material, particularly in the context of mm and sub-mm wave applications for front-end radio astronomy receivers and space applications, both at room temperature and cryogenic conditions.
- 20 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (2) , 187-190
Wafer Level Integration of Sub-THz and THz Systems
The letter presents a wafer level integration technology for sub-THz and THz systems. The developed integration process relies on deep reactive ion etching (DRIE) micromachining and Au-Au wafer bonding technology of silicon wafer substrates. The method allows integration of individual standard monolithic microwave integrated circuits (MMICs) of different technologies into the same Si package. The process includes only standard fabrication steps than can be automated. The integration process is scalable and cost efficient for future sub-THz and THz communication and sensing applications.
- 20 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (2) , 187-190
Wafer Level Integration of Sub-THz and THz Systems
The letter presents a wafer level integration technology for sub-THz and THz systems. The developed integration process relies on deep reactive ion etching (DRIE) micromachining and Au-Au wafer bonding technology of silicon wafer substrates. The method allows integration of individual standard monolithic microwave integrated circuits (MMICs) of different technologies into the same Si package. The process includes only standard fabrication steps than can be automated. The integration process is scalable and cost efficient for future sub-THz and THz communication and sensing applications.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (6) , 3505-3513
Integrated Radiometer at 240 GHz With SiGe MMIC Detector and GRIN Silicon Lens
We describe an integrated radiometer at 240 GHz consisting of a direct detection MMIC fabricated in BiCMOS SiGe and a silicon gradient refractive index (GRIN) lens. The planar GRIN lens enables placing the MMIC with an on-chip dipole antenna directly on the GRIN lens in the focal point of the lens. We describe, how this method of integration can be extended to larger detector arrays while presenting results of a single pixel in this article. The direct detection MMIC includes an on-chip dipole antenna, a low-noise amplifier (LNA), and a diode detector. The radiometer bandwidth (BW) is 38 GHz, defined by the monolithic microwave integrated circuit (MMIC). The GRIN lens is fabricated in high-resistivity silicon and has a gain of 12.2 dBi at 240 GHz with an on-chip feed antenna. The integrated radiometer achieves noise-equivalent temperature difference (NETD) of 0.5 K/Hz $^{1/2}$ . The radiometer with external chopping is stable up to an integration time of 100 s, as demonstrated by the Allan variance measurement, where an NETD of 0.03 K with 100-s integration time is measured.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (6) , 3505-3513
Integrated Radiometer at 240 GHz With SiGe MMIC Detector and GRIN Silicon Lens
We describe an integrated radiometer at 240 GHz consisting of a direct detection MMIC fabricated in BiCMOS SiGe and a silicon gradient refractive index (GRIN) lens. The planar GRIN lens enables placing the MMIC with an on-chip dipole antenna directly on the GRIN lens in the focal point of the lens. We describe, how this method of integration can be extended to larger detector arrays while presenting results of a single pixel in this article. The direct detection MMIC includes an on-chip dipole antenna, a low-noise amplifier (LNA), and a diode detector. The radiometer bandwidth (BW) is 38 GHz, defined by the monolithic microwave integrated circuit (MMIC). The GRIN lens is fabricated in high-resistivity silicon and has a gain of 12.2 dBi at 240 GHz with an on-chip feed antenna. The integrated radiometer achieves noise-equivalent temperature difference (NETD) of 0.5 K/Hz $^{1/2}$ . The radiometer with external chopping is stable up to an integration time of 100 s, as demonstrated by the Allan variance measurement, where an NETD of 0.03 K with 100-s integration time is measured.
- Open Access
- 6 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 23565-23577
220-240-GHz High-Gain Phase Shifter Chain and Power Amplifier for Scalable Large Phased-Arrays
This paper focuses on the design aspects of the key components for a scalable phased-array system over the 200 GHz frequency range. A high-gain phase shifter chain for 220 to 240 GHz frequency range and a high-gain power amplifier (PA) with a high output power are designed in a 0.13- $\mu \text{m}$ SiGe BiCMOS technology. The phase shifter chain includes a low-noise amplifier (LNA), a vector modulator phase shifter (PS), and a gain-enhancing amplifier. The LNA is a five-stage cascode design. The vector modulator core is realized by two variable gain amplifiers based on the Gilbert cell architecture. A four-stage cascode design is used for the gain-enhancing amplifier. The phase shifter chain shows a measured gain of 18 dB at 230 GHz with a $360 {\mathrm { ^{\circ}}}$ phase tuning range and more than 10 dB of gain control. The chip achieves a minimum measured noise figure of 11.5 dB at 230 GHz and shows a wideband noise characteristic. The complete phase shifter chain chip consumes a dc power of 153 mW and occupies a 1.41 mm2 area. A high-power PA that is critical for a large phased-array system is designed. This paper presents a unique 4-way power combining technique utilizing a differential quadrature coupler. The realized balanced PA occupies an area of 0.67 mm2 and shows a measured peak gain of 21 dB at 244 GHz. The PA consumes 819 mW of dc power and delivers a maximum saturated output power $(P_{sat})$ of 7.1 dBm at 244 GHz and more than 4.3 dBm of $P_{sat}$ from 230 to 255 GHz.
- 6 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 23565-23577
Open Access220-240-GHz High-Gain Phase Shifter Chain and Power Amplifier for Scalable Large Phased-Arrays
This paper focuses on the design aspects of the key components for a scalable phased-array system over the 200 GHz frequency range. A high-gain phase shifter chain for 220 to 240 GHz frequency range and a high-gain power amplifier (PA) with a high output power are designed in a 0.13- $\mu \text{m}$ SiGe BiCMOS technology. The phase shifter chain includes a low-noise amplifier (LNA), a vector modulator phase shifter (PS), and a gain-enhancing amplifier. The LNA is a five-stage cascode design. The vector modulator core is realized by two variable gain amplifiers based on the Gilbert cell architecture. A four-stage cascode design is used for the gain-enhancing amplifier. The phase shifter chain shows a measured gain of 18 dB at 230 GHz with a $360 {\mathrm { ^{\circ}}}$ phase tuning range and more than 10 dB of gain control. The chip achieves a minimum measured noise figure of 11.5 dB at 230 GHz and shows a wideband noise characteristic. The complete phase shifter chain chip consumes a dc power of 153 mW and occupies a 1.41 mm2 area. A high-power PA that is critical for a large phased-array system is designed. This paper presents a unique 4-way power combining technique utilizing a differential quadrature coupler. The realized balanced PA occupies an area of 0.67 mm2 and shows a measured peak gain of 21 dB at 244 GHz. The PA consumes 819 mW of dc power and delivers a maximum saturated output power $(P_{sat})$ of 7.1 dBm at 244 GHz and more than 4.3 dBm of $P_{sat}$ from 230 to 255 GHz.
- Open Access
- 14 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 13 (2) , 153-160
In-Line Vector Modulator Integration in Dielectric-Filled Waveguide
This paper proposes a scalable substrate-integrated waveguide (SIW) module accommodating an in-line vector modulator monolithic millimeter integrated circuit (MMIC). The SIW module is realized with low-temperature co-fired ceramic (LTCC) technology, and it can be inserted in a dielectric-filled waveguide (DFWG). The module combines λ g /4-transformer-based E-plane tapering and SIWs on LTCC with the wire-bonded vector modulator. The proposed active LTCC module and two passive test structures (i.e., a constant-height-SIW module and a SIW module with E-plane taperings) are manufactured and tested as in-line modules in a DFWG. The passive test structures with the waveguide-to-DFWG and DFWG-to-SIW transitions measure 3.1 dB and 4.6 dB of insertion loss on average, respectively, at the 71–81 GHz frequency range. The active LTCC module measurements demonstrate a dielectric-filled waveguide with phase and amplitude tuning capability and gain up to 17.6 dB within the same frequency range. A four-channel mock-up module with λ 0 /2 channel spacing is designed and manufactured to demonstrate the scalability of the design.
- 14 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 13 (2) , 153-160
Open AccessIn-Line Vector Modulator Integration in Dielectric-Filled Waveguide
This paper proposes a scalable substrate-integrated waveguide (SIW) module accommodating an in-line vector modulator monolithic millimeter integrated circuit (MMIC). The SIW module is realized with low-temperature co-fired ceramic (LTCC) technology, and it can be inserted in a dielectric-filled waveguide (DFWG). The module combines λ g /4-transformer-based E-plane tapering and SIWs on LTCC with the wire-bonded vector modulator. The proposed active LTCC module and two passive test structures (i.e., a constant-height-SIW module and a SIW module with E-plane taperings) are manufactured and tested as in-line modules in a DFWG. The passive test structures with the waveguide-to-DFWG and DFWG-to-SIW transitions measure 3.1 dB and 4.6 dB of insertion loss on average, respectively, at the 71–81 GHz frequency range. The active LTCC module measurements demonstrate a dielectric-filled waveguide with phase and amplitude tuning capability and gain up to 17.6 dB within the same frequency range. A four-channel mock-up module with λ 0 /2 channel spacing is designed and manufactured to demonstrate the scalability of the design.
- 17 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (7) , 883-886
A 200–250-GHz Phase Shifter Utilizing a Compact and Wideband Differential Quadrature Coupler
This letter presents the design of a 200–250-GHz compact vector modulator (VM) phase shifter in a 0.13- $\mu \text{m}$ SiGe bipolar complementary metal-oxide-semiconductor (BiCMOS) technology. A compact, low-loss, and wideband differential quadrature coupler is used to generate differential I/Q signals. The design details of the millimeter-wave wideband differential coupler is presented and compared with other I/Q generators by the 3-D electromagnetic (EM)-simulated results. The VM core is realized by two variable gain amplifiers based on Gilbert cell architecture. The measured phase shifter shows a gain of −10.3 dB for the maximum gain setting at 230 GHz. The phase shifter shows a −17 dB of gain for full 360° phase tuning range and a 10 dB of gain control. The maximum rms gain error and the phase error are 1.25 dB and 10°, respectively, from 200 to 250 GHz. The chip consumes a dc power of 55 mW and occupies a core area of 0.09 mm 2 .
- 17 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (7) , 883-886
A 200–250-GHz Phase Shifter Utilizing a Compact and Wideband Differential Quadrature Coupler
This letter presents the design of a 200–250-GHz compact vector modulator (VM) phase shifter in a 0.13- $\mu \text{m}$ SiGe bipolar complementary metal-oxide-semiconductor (BiCMOS) technology. A compact, low-loss, and wideband differential quadrature coupler is used to generate differential I/Q signals. The design details of the millimeter-wave wideband differential coupler is presented and compared with other I/Q generators by the 3-D electromagnetic (EM)-simulated results. The VM core is realized by two variable gain amplifiers based on Gilbert cell architecture. The measured phase shifter shows a gain of −10.3 dB for the maximum gain setting at 230 GHz. The phase shifter shows a −17 dB of gain for full 360° phase tuning range and a 10 dB of gain control. The maximum rms gain error and the phase error are 1.25 dB and 10°, respectively, from 200 to 250 GHz. The chip consumes a dc power of 55 mW and occupies a core area of 0.09 mm 2 .
- 25 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (11) , 4689-4696
Millimeter-Wave Amplifier-Based Noise Sources in SiGe BiCMOS Technology
This article describes the development and characterization of wideband millimeter-wave noise sources based on SiGe BiCMOS amplifiers. Two single-ended three-stage amplifier-based noise sources reached excess noise ratio (ENR) values over 20 dB from 120 to 220 GHz with 20 mA of the bias current from a 2.3-V supply. We also introduce a novel switchable noise source employing the Lange coupler for providing wideband matching in both ON and OFF configurations of the noise source. The Lange coupler-based noise source has better than 12-dB matching from 90 to 270 GHz with an ENR of better than 15 dB from 125 to 235 GHz.
- 25 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (11) , 4689-4696
Millimeter-Wave Amplifier-Based Noise Sources in SiGe BiCMOS Technology
This article describes the development and characterization of wideband millimeter-wave noise sources based on SiGe BiCMOS amplifiers. Two single-ended three-stage amplifier-based noise sources reached excess noise ratio (ENR) values over 20 dB from 120 to 220 GHz with 20 mA of the bias current from a 2.3-V supply. We also introduce a novel switchable noise source employing the Lange coupler for providing wideband matching in both ON and OFF configurations of the noise source. The Lange coupler-based noise source has better than 12-dB matching from 90 to 270 GHz with an ENR of better than 15 dB from 125 to 235 GHz.
- Open Access
- 31 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 52872-52882
Beam-Reconfigurable Antenna Based on Vector Modulator and Rotman Lens on LTCC
A beam-switching array is designed using a 4×6 Rotman lens as a beam-forming network to switch the beam towards -30°, -10°, 10°, and 30°. Six substrate integrated waveguide fed 1×4 microstrip patch arrays are used as the radiating elements. The beam-switching array is designed on the LTCC substrate to operate at 71-76 GHz. In this work, the feasibility of implementing a beam-switching network with a vector modulator (VM) integrated circuit as switching element is studied for the first time. The measured radiation pattern of the beam-switching array with the VM is in line with the simulated radiation pattern. The measured peak realized gain of the beam port 1, 2, 3, and 4 with 3-dB backoff gain of the VM are 17, 17, 17.8, 16.9 dBi at 75 GHz, respectively. In addition, the work demonstrates the possibility of beam-reconfigurability in beam-switching array by simultaneous excitation of the beam ports in optimum phase using the VM. The simultaneous excitation of the adjacent two ports, 1-2, 2-3, and 3-4, steer the beam towards -19°, 0°, and 19°, respectively, which improves the beam cross-over level. With various combinations of simultaneous excitation, the half power beam-width of the beam-switching array is varied from 17.8° to 75°.
- 31 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 52872-52882
Open AccessBeam-Reconfigurable Antenna Based on Vector Modulator and Rotman Lens on LTCC
A beam-switching array is designed using a 4×6 Rotman lens as a beam-forming network to switch the beam towards -30°, -10°, 10°, and 30°. Six substrate integrated waveguide fed 1×4 microstrip patch arrays are used as the radiating elements. The beam-switching array is designed on the LTCC substrate to operate at 71-76 GHz. In this work, the feasibility of implementing a beam-switching network with a vector modulator (VM) integrated circuit as switching element is studied for the first time. The measured radiation pattern of the beam-switching array with the VM is in line with the simulated radiation pattern. The measured peak realized gain of the beam port 1, 2, 3, and 4 with 3-dB backoff gain of the VM are 17, 17, 17.8, 16.9 dBi at 75 GHz, respectively. In addition, the work demonstrates the possibility of beam-reconfigurability in beam-switching array by simultaneous excitation of the beam ports in optimum phase using the VM. The simultaneous excitation of the adjacent two ports, 1-2, 2-3, and 3-4, steer the beam towards -19°, 0°, and 19°, respectively, which improves the beam cross-over level. With various combinations of simultaneous excitation, the half power beam-width of the beam-switching array is varied from 17.8° to 75°.
- 30 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (5) , 520-523
An mm-Wave CMOS I–Q Subharmonic Resistive Mixer for Wideband Zero-IF Receivers
In this letter, we propose a novel wideband subharmonically pumped fully differential I-Q resistive mixer architecture, which eliminates the necessity for on-chip dc-blocking capacitors to integrate IF amplifiers. The proposed differential subharmonic mixer topology is verified by presenting a CMOS millimeter-wave monolithic integrated circuit (MMIC), which includes the mixer and two on-chip differential IF amplifiers at the mixer's I- and Q-channels. The 3-dB IF frequency bandwidth is measured from 0.01 to 5 GHz with a peak conversion gain (CG) of -2 dB and an image rejection ratio (IRR) of more than 25 dB over the IF frequency range. The proposed mixer covers the input signal (RF) frequency from 170 to 185 GHz. The mixer has also been tested with an on-chip voltage-controlled oscillator (VCO) and shows -4.7-dB CG with a 3-dB IF bandwidth from 0.01 to 4.5 GHz.
- 30 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (5) , 520-523
An mm-Wave CMOS I–Q Subharmonic Resistive Mixer for Wideband Zero-IF Receivers
In this letter, we propose a novel wideband subharmonically pumped fully differential I-Q resistive mixer architecture, which eliminates the necessity for on-chip dc-blocking capacitors to integrate IF amplifiers. The proposed differential subharmonic mixer topology is verified by presenting a CMOS millimeter-wave monolithic integrated circuit (MMIC), which includes the mixer and two on-chip differential IF amplifiers at the mixer's I- and Q-channels. The 3-dB IF frequency bandwidth is measured from 0.01 to 5 GHz with a peak conversion gain (CG) of -2 dB and an image rejection ratio (IRR) of more than 25 dB over the IF frequency range. The proposed mixer covers the input signal (RF) frequency from 170 to 185 GHz. The mixer has also been tested with an on-chip voltage-controlled oscillator (VCO) and shows -4.7-dB CG with a 3-dB IF bandwidth from 0.01 to 4.5 GHz.
- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (7) , 2845-2855
Scalable 60 GHz FMCW Frequency-Division Multiplexing MIMO Radar
In this article, a 60-GHz frequency-modulated continuous-wave (FMCW) multiple-input multiple-output (MIMO) radar system using frequency-division multiplexing for TX signal separation is presented. Four-channel transmitter and receiver chips were designed using 130 nm SiGe process. The total number of TX and RX channels can be scaled by the number of chips in the system while still maintaining phase coherence between the channels. 2-D and 3-D object localization measurements are made with four TX and eight RX channel systems. In the 2-D configuration, the radar system is capable of a 5-cm range resolution and 3.5° angular resolution.
- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (7) , 2845-2855
Scalable 60 GHz FMCW Frequency-Division Multiplexing MIMO Radar
In this article, a 60-GHz frequency-modulated continuous-wave (FMCW) multiple-input multiple-output (MIMO) radar system using frequency-division multiplexing for TX signal separation is presented. Four-channel transmitter and receiver chips were designed using 130 nm SiGe process. The total number of TX and RX channels can be scaled by the number of chips in the system while still maintaining phase coherence between the channels. 2-D and 3-D object localization measurements are made with four TX and eight RX channel systems. In the 2-D configuration, the radar system is capable of a 5-cm range resolution and 3.5° angular resolution.