Helmut Köck
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Helmut Köck has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
Michael Glavanovics
9 shared publications- Debbie G. Senesky
Department of Aeronautics and Astronautics, Stanford University 5 , Stanford, California 94305
7 shared publications - Karen M. Dowling
Delft University of Technology 1 Department of Microelectronics Delft
7 shared publications - Udo Ausserlechner
Infineon Technologies AG, Villach, Austria
7 shared publications Stefano de Filippis
KAI - Kompetenzzentrum Automobil- und Industrie-Elektronik GmbH, Europastrasse 8, A-9524 Villach, Austria
6 shared publications- Hannah S. Alpert
NASA Ames Research Center
5 shared publications
Latest Publications
- Open Access
- 14 February 2025
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 11 (1) , 1-13
Inverted pyramid 3-axis silicon Hall-effect magnetic sensor with offset cancellation
Microelectronic magnetic sensors are essential in diverse applications, including automotive, industrial, and consumer electronics. Hall-effect devices hold the largest share of the magnetic sensor market, and they are particularly valued for their reliability, low cost and CMOS compatibility. This paper introduces a novel 3-axis Hall-effect sensor element based on an inverted pyramid structure, realized by leveraging MEMS micromachining and CMOS processing. The devices are manufactured by etching the pyramid openings with TMAH and implanting the sloped walls with n-dopants to define the active area. Through the use of various bias-sense detection modes, the device is able to detect both in-plane and out-of-plane magnetic fields within a single compact structure. In addition, the offset can be significantly reduced by one to three orders of magnitude by employing the current-spinning method. The device presented in this work demonstrated high in-plane and out-of-plane current- and voltage-related sensitivities ranging between 64.1 to 198 V A−1 T− 1 and 14.8 to 21.4 mV V−1 T−1, with crosstalk below 4.7%. The sensor exhibits a thermal noise floor which corresponds to approximately $$0.5\,\mu \text{T}/\sqrt{\text{Hz}}$$ at 1.31 V supply. This novel Hall-effect sensor represents a promising and simpler alternative to existing state-of-the-art 3-axis magnetic sensors, offering a viable solution for precise and reliable magnetic field sensing in various applications such as position feedback and power monitoring.- 14 February 2025
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 11 (1) , 1-13
Open AccessInverted pyramid 3-axis silicon Hall-effect magnetic sensor with offset cancellation
Microelectronic magnetic sensors are essential in diverse applications, including automotive, industrial, and consumer electronics. Hall-effect devices hold the largest share of the magnetic sensor market, and they are particularly valued for their reliability, low cost and CMOS compatibility. This paper introduces a novel 3-axis Hall-effect sensor element based on an inverted pyramid structure, realized by leveraging MEMS micromachining and CMOS processing. The devices are manufactured by etching the pyramid openings with TMAH and implanting the sloped walls with n-dopants to define the active area. Through the use of various bias-sense detection modes, the device is able to detect both in-plane and out-of-plane magnetic fields within a single compact structure. In addition, the offset can be significantly reduced by one to three orders of magnitude by employing the current-spinning method. The device presented in this work demonstrated high in-plane and out-of-plane current- and voltage-related sensitivities ranging between 64.1 to 198 V A−1 T− 1 and 14.8 to 21.4 mV V−1 T−1, with crosstalk below 4.7%. The sensor exhibits a thermal noise floor which corresponds to approximately $$0.5\,\mu \text{T}/\sqrt{\text{Hz}}$$ at 1.31 V supply. This novel Hall-effect sensor represents a promising and simpler alternative to existing state-of-the-art 3-axis magnetic sensors, offering a viable solution for precise and reliable magnetic field sensing in various applications such as position feedback and power monitoring. - Open Access
Inverted Pyramid 3-axis Silicon Hall Effect Magnetic Sensor With Offset Cancellation
Microelectronic magnetic sensors are essential in diverse applications, including automotive, industrial, and consumer electronics. Hall-effect devices hold the largest share of the magnetic sensor market, and they are particularly valued for their reliability, low cost and CMOS compatibility. This paper introduces a novel 3-axis Hall-effect sensor element based on an inverted pyramid structure, realized by leveraging MEMS micromachining and CMOS processing. The devices are manufactured by etching the pyramid openings with TMAH and implanting the sloped walls with n-dopants to define the active area. Through the use of various bias-sense detection modes, the device is able to detect both in-plane and out-of-plane magnetic fields within a single compact structure. In addition, the offset can be significantly reduced by one to three orders of magnitude by employing the current-spinning method. The device presented in this work demonstrated high in-plane and out-of-plane current- and voltage-related sensitivities ranging between 64.1 to 198 V A$^{-1}$ T$^{-1}$ and 14.8 to 21.4 mV V$^{-1}$ T$^{-1}$, with crosstalk below 3.7 %. The sensor exhibits a thermal noise floor which corresponds to approximately 0.5 $μ$T/$\sqrt{Hz}$ at 1.31 V supply. This novel Hall-effect sensor represents a promising and simpler alternative to existing state-of-the-art 3-axis magnetic sensors, offering a viable solution for precise and reliable magnetic field sensing in various applications such as position feedback and power monitoring.Open AccessInverted Pyramid 3-axis Silicon Hall Effect Magnetic Sensor With Offset Cancellation
Microelectronic magnetic sensors are essential in diverse applications, including automotive, industrial, and consumer electronics. Hall-effect devices hold the largest share of the magnetic sensor market, and they are particularly valued for their reliability, low cost and CMOS compatibility. This paper introduces a novel 3-axis Hall-effect sensor element based on an inverted pyramid structure, realized by leveraging MEMS micromachining and CMOS processing. The devices are manufactured by etching the pyramid openings with TMAH and implanting the sloped walls with n-dopants to define the active area. Through the use of various bias-sense detection modes, the device is able to detect both in-plane and out-of-plane magnetic fields within a single compact structure. In addition, the offset can be significantly reduced by one to three orders of magnitude by employing the current-spinning method. The device presented in this work demonstrated high in-plane and out-of-plane current- and voltage-related sensitivities ranging between 64.1 to 198 V A$^{-1}$ T$^{-1}$ and 14.8 to 21.4 mV V$^{-1}$ T$^{-1}$, with crosstalk below 3.7 %. The sensor exhibits a thermal noise floor which corresponds to approximately 0.5 $μ$T/$\sqrt{Hz}$ at 1.31 V supply. This novel Hall-effect sensor represents a promising and simpler alternative to existing state-of-the-art 3-axis magnetic sensors, offering a viable solution for precise and reliable magnetic field sensing in various applications such as position feedback and power monitoring. - 27 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
Effect of Geometry on the Frequency Limit of GaAs/AlGaAs 2-D Electron Gas (2DEG) Hall Effect Sensors
High-frequency wideband Hall effect sensors can measure currents in power electronics that operate at higher frequencies (in MHz range). We experimentally investigated the frequency limit of Hall effect sensor designs based on a 2-dimensional electron gas (2DEG) gallium arsenide/aluminum gallium arsenide (GaAs/AlGaAs) heterostructures. For the first time, an experimental investigation into the frequency limit of 2DEG Hall effect sensor is shown. The frequency limit is measured and compared for four GaAs/AlGaAs Hall effect sensor designs where the Ohmic contact length (contact geometry) is varied across the four devices. By varying the geometry, the trade-off in sensitivity and frequency limit is explored and the underlying causes of the frequency limit from the resistance and capacitance is investigated. Current spinning, the traditional method to remove offset noise, imposes a practical frequency limit on Hall effect sensors. The actual frequency limit, without current spinning, is an order of magnitude higher. An experimental frequency limit of 46MHz is measured for 2DEG GaAs/AlGaAs sensor
- 27 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
Effect of Geometry on the Frequency Limit of GaAs/AlGaAs 2-D Electron Gas (2DEG) Hall Effect Sensors
High-frequency wideband Hall effect sensors can measure currents in power electronics that operate at higher frequencies (in MHz range). We experimentally investigated the frequency limit of Hall effect sensor designs based on a 2-dimensional electron gas (2DEG) gallium arsenide/aluminum gallium arsenide (GaAs/AlGaAs) heterostructures. For the first time, an experimental investigation into the frequency limit of 2DEG Hall effect sensor is shown. The frequency limit is measured and compared for four GaAs/AlGaAs Hall effect sensor designs where the Ohmic contact length (contact geometry) is varied across the four devices. By varying the geometry, the trade-off in sensitivity and frequency limit is explored and the underlying causes of the frequency limit from the resistance and capacitance is investigated. Current spinning, the traditional method to remove offset noise, imposes a practical frequency limit on Hall effect sensors. The actual frequency limit, without current spinning, is an order of magnitude higher. An experimental frequency limit of 46MHz is measured for 2DEG GaAs/AlGaAs sensor
- 11 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 29 (5) , 669-676
Low Offset and Noise in High Biased GaN 2DEG Hall-Effect Plates Investigated With Infrared Microscopy
This article presents GaN two-dimensional electron gas (2DEG) Hall plates with low residual offset and noise at 3 V input bias. We studied devices made from three consecutive fabrication generations through current spinning offset measurements in a zero-field chamber. When operated above 1 V, the first-generation devices charted high residual offsets 1 mT. We reduced these residual offsets by three orders of magnitude in later device generations. Two experiments were performed to confirm the improvements. First, the GaN 2DEG Hall-effect plates were measured with infrared microscopy during current spinning to investigate current crowding and Joule heating. The low offset devices had minimal thermal gradients while the high offset devices had large thermal variations during current spinning. Second, zero-field current spinning was used to compare GaN 2DEG Hall-effect plates against typical commercial silicon Hall-effect plates. The Si devices had residual offsets 10μT biased at 3 V and AlGaN/GaN devices had residual offset c4 μT at 3 V, and an InAlN/GaN devices operated at 2 V had a residual offset c4 μT. Thus, for the first time, GaN 2DEG Hall-effect plates were shown to operate with high bias with low offsets and noise, which enables high fidelity sensing applications in extreme environments.
- 11 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 29 (5) , 669-676
Low Offset and Noise in High Biased GaN 2DEG Hall-Effect Plates Investigated With Infrared Microscopy
This article presents GaN two-dimensional electron gas (2DEG) Hall plates with low residual offset and noise at 3 V input bias. We studied devices made from three consecutive fabrication generations through current spinning offset measurements in a zero-field chamber. When operated above 1 V, the first-generation devices charted high residual offsets 1 mT. We reduced these residual offsets by three orders of magnitude in later device generations. Two experiments were performed to confirm the improvements. First, the GaN 2DEG Hall-effect plates were measured with infrared microscopy during current spinning to investigate current crowding and Joule heating. The low offset devices had minimal thermal gradients while the high offset devices had large thermal variations during current spinning. Second, zero-field current spinning was used to compare GaN 2DEG Hall-effect plates against typical commercial silicon Hall-effect plates. The Si devices had residual offsets 10μT biased at 3 V and AlGaN/GaN devices had residual offset c4 μT at 3 V, and an InAlN/GaN devices operated at 2 V had a residual offset c4 μT. Thus, for the first time, GaN 2DEG Hall-effect plates were shown to operate with high bias with low offsets and noise, which enables high fidelity sensing applications in extreme environments.
- Open Access
- 1 February 2020
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 91 (2) , 025003
Sensitivity of 2DEG-based Hall-effect sensors at high temperatures
The magnetic sensitivity of Hall-effect sensors made of InAlN/GaN and AlGaN/GaN heterostructures was measured between room temperature and 576 °C. Both devices showed decreasing voltage-scaled magnetic sensitivity at high temperatures, declining from 53 mV/V/T to 8.3 mV/V/T for the InAlN/GaN sample and from 89 mV/V/T to 8.5 mV/V/T for the AlGaN/GaN sample, corresponding to the decreasing electron mobility due to scattering effects at elevated temperatures. Alternatively, current-scaled sensitivities remained stable over the temperature range, only varying by 13.1% from the mean of 26.3 V/A/T and 10.5% from the mean of 60.2 V/A/T for the InAlN/GaN and AlGaN/GaN samples, respectively. This is due to the minimal temperature dependence of the electron sheet density on the 2-dimensional electron gas (2DEG). Both devices showed consistency in their voltage- and current-scaled sensitivity over multiple temperature cycles as well as nearly full recovery when returned to room temperature after thermal cycling. Additionally, an AlGaN/GaN sample held at 576 °C for 12 h also showed nearly full recovery at room temperature, further suggesting that GaN-based Hall-effect sensors are a good candidate for use in high temperature applications.
- 1 February 2020
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 91 (2) , 025003
Open AccessSensitivity of 2DEG-based Hall-effect sensors at high temperatures
The magnetic sensitivity of Hall-effect sensors made of InAlN/GaN and AlGaN/GaN heterostructures was measured between room temperature and 576 °C. Both devices showed decreasing voltage-scaled magnetic sensitivity at high temperatures, declining from 53 mV/V/T to 8.3 mV/V/T for the InAlN/GaN sample and from 89 mV/V/T to 8.5 mV/V/T for the AlGaN/GaN sample, corresponding to the decreasing electron mobility due to scattering effects at elevated temperatures. Alternatively, current-scaled sensitivities remained stable over the temperature range, only varying by 13.1% from the mean of 26.3 V/A/T and 10.5% from the mean of 60.2 V/A/T for the InAlN/GaN and AlGaN/GaN samples, respectively. This is due to the minimal temperature dependence of the electron sheet density on the 2-dimensional electron gas (2DEG). Both devices showed consistency in their voltage- and current-scaled sensitivity over multiple temperature cycles as well as nearly full recovery when returned to room temperature after thermal cycling. Additionally, an AlGaN/GaN sample held at 576 °C for 12 h also showed nearly full recovery at room temperature, further suggesting that GaN-based Hall-effect sensors are a good candidate for use in high temperature applications.
- Open Access
Temperature Dependence of Sensitivity of 2DEG-Based Hall-Effect Sensors
The magnetic sensitivity of Hall-effect sensors made of InAlN/GaN and AlGaN/GaN heterostructures was measured between room temperature and 576{\deg}C. Both devices showed decreasing voltage-scaled magnetic sensitivity at high temperature, declining from 53 to 8.3 mV/V/T for the InAlN/GaN sample and from 89 to 8.5 mV/V/T for the AlGaN/GaN sample, corresponding to the decreasing electron mobility due to scattering effects at elevated temperatures. Alternatively, current-scaled sensitivities remained stable over the temperature range, only varying by 13.1% from the mean of 26.3 V/A/T and 10.5% from the mean of 60.2 V/A/T for the InAlN/GaN and AlGaN/GaN samples respectively. This is due to the minimal temperature dependence of the electron sheet density on the 2-dimensional electron gas (2DEG). Both devices showed consistency in their voltage- and current-scaled sensitivity over multiple temperature cycles as well as nearly full recovery when returned to room temperature after thermal cycling. Additionally, an AlGaN/GaN sample held at 576{\deg}C for 12 hours also showed nearly full recovery at room temperature, further suggesting that GaN-based Hall-effect sensors are a good candidate for use in high temperature applications.
Open AccessTemperature Dependence of Sensitivity of 2DEG-Based Hall-Effect Sensors
The magnetic sensitivity of Hall-effect sensors made of InAlN/GaN and AlGaN/GaN heterostructures was measured between room temperature and 576{\deg}C. Both devices showed decreasing voltage-scaled magnetic sensitivity at high temperature, declining from 53 to 8.3 mV/V/T for the InAlN/GaN sample and from 89 to 8.5 mV/V/T for the AlGaN/GaN sample, corresponding to the decreasing electron mobility due to scattering effects at elevated temperatures. Alternatively, current-scaled sensitivities remained stable over the temperature range, only varying by 13.1% from the mean of 26.3 V/A/T and 10.5% from the mean of 60.2 V/A/T for the InAlN/GaN and AlGaN/GaN samples respectively. This is due to the minimal temperature dependence of the electron sheet density on the 2-dimensional electron gas (2DEG). Both devices showed consistency in their voltage- and current-scaled sensitivity over multiple temperature cycles as well as nearly full recovery when returned to room temperature after thermal cycling. Additionally, an AlGaN/GaN sample held at 576{\deg}C for 12 hours also showed nearly full recovery at room temperature, further suggesting that GaN-based Hall-effect sensors are a good candidate for use in high temperature applications.
- 7 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 3 (3) , 1-4
Micro-Tesla Offset in Thermally Stable AlGaN/GaN 2DEG Hall Plates Using Current Spinning
This article describes the characterization of a low-offset Hall plate using the AlGaN/GaN 2-D electron gas (2DEG). A four-phase current spinning technique was used to reduce the sensor offset voltage to values in the range of ~20 nV, which corresponds to a low residual offset of ~3.4 ± 2 μT when supplied with low voltages (0.25-1 V). These offsets are 30x smaller than the values previously reported for GaN Hall plates, and it is on par with state-of-the-art current-spun silicon (Si) Hall plates. In addition, the offset does not exceed 10 μT even at a higher supply voltage of 2 V. Current spinning was done with a relay matrix at a switching frequency of 1 Hz to enable an offset reduction. The sensor also shows stable current-scaled sensitivity over a wide temperature range of -100 °C to 200 °C, with a temperature coefficient of ~100 ppm/°C. This value is at least 3x better than the state-of-the art Si Hall plates. Additionally, the sensor's voltage-related sensitivity (~57 mV/V/T) is similar to that of the state-of-the-art Si Hall plates. Because of the low offset values enabled by current spinning, the AlGaN/GaN 2DEG Hall plates are viable candidates for low-field current and magnetic sensing in high-temperature environments.
- 7 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 3 (3) , 1-4
Micro-Tesla Offset in Thermally Stable AlGaN/GaN 2DEG Hall Plates Using Current Spinning
This article describes the characterization of a low-offset Hall plate using the AlGaN/GaN 2-D electron gas (2DEG). A four-phase current spinning technique was used to reduce the sensor offset voltage to values in the range of ~20 nV, which corresponds to a low residual offset of ~3.4 ± 2 μT when supplied with low voltages (0.25-1 V). These offsets are 30x smaller than the values previously reported for GaN Hall plates, and it is on par with state-of-the-art current-spun silicon (Si) Hall plates. In addition, the offset does not exceed 10 μT even at a higher supply voltage of 2 V. Current spinning was done with a relay matrix at a switching frequency of 1 Hz to enable an offset reduction. The sensor also shows stable current-scaled sensitivity over a wide temperature range of -100 °C to 200 °C, with a temperature coefficient of ~100 ppm/°C. This value is at least 3x better than the state-of-the art Si Hall plates. Additionally, the sensor's voltage-related sensitivity (~57 mV/V/T) is similar to that of the state-of-the-art Si Hall plates. Because of the low offset values enabled by current spinning, the AlGaN/GaN 2DEG Hall plates are viable candidates for low-field current and magnetic sensing in high-temperature environments.
- 25 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (10) , 3640-3646
Effect of Geometry on Sensitivity and Offset of AlGaN/GaN and InAlN/GaN Hall-Effect Sensors
- 25 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (10) , 3640-3646
Effect of Geometry on Sensitivity and Offset of AlGaN/GaN and InAlN/GaN Hall-Effect Sensors
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Multi-physics based system simulations for magnetic sensors
Today's magnetic sensor applications demand a detailed understanding of all relevant system components. This work presents a holistic simulation methodology to account for the close interaction between ferromagnetic target objects, magnetic circuit designs and specific sensor characteristics of relevant Hall and xMR technologies.The core element of this simulation approach is a proprietary developed finite element/boundary element based magnetic simulation environment capable to accurately calculate isotropic as well as anisotropic permanent magnets in a ferromagnetic target wheel setup. Available simulation features are superior in terms of field accuracy and computational cost compared to commercially available tools. Incorporating the magnetic simulation core in a holistic simulation design flow offers the integration of application driven key parameters like target wheel rotation or air gap variation and ultimately translates the results to electrical signals. Target wheels, package details including magnet design, chip layout and sensor specific properties are parametrized and investigated in detail. The numerical results of a target wheel optimization based on the multi-physics simulation approach presented in this work are eventually compared to actual measurements. The presented results clearly highlight the potential to support future product developments in the field of magnetic sensors.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Multi-physics based system simulations for magnetic sensors
Today's magnetic sensor applications demand a detailed understanding of all relevant system components. This work presents a holistic simulation methodology to account for the close interaction between ferromagnetic target objects, magnetic circuit designs and specific sensor characteristics of relevant Hall and xMR technologies.The core element of this simulation approach is a proprietary developed finite element/boundary element based magnetic simulation environment capable to accurately calculate isotropic as well as anisotropic permanent magnets in a ferromagnetic target wheel setup. Available simulation features are superior in terms of field accuracy and computational cost compared to commercially available tools. Incorporating the magnetic simulation core in a holistic simulation design flow offers the integration of application driven key parameters like target wheel rotation or air gap variation and ultimately translates the results to electrical signals. Target wheels, package details including magnet design, chip layout and sensor specific properties are parametrized and investigated in detail. The numerical results of a target wheel optimization based on the multi-physics simulation approach presented in this work are eventually compared to actual measurements. The presented results clearly highlight the potential to support future product developments in the field of magnetic sensors.
- 7 July 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 31 (4) , 3128-3140
Electrothermal Multiscale Modeling and Simulation Concepts for Power Electronics
This paper presents a finite-element-based simulation methodology to improve on multiscale modeling and analysis limitations of power electronics development. The method utilizes homogenization and nonmatching grid concepts to offer a high degree of flexibility and reduce computational effort. The applied homogenization method provides effective material properties to realize full-chip modeling performance without the need to model geometric details. The concept of nonmatching grids allows the inclusion of a subregion with substantially finer mesh than its surrounding regions. This allows the flexible integration of micrometer scale geometries with a high degree of detail within the full-chip model. Both concepts are thoroughly introduced and an application to a state-of-the-art power electronics semiconductor technology is presented. This paper focuses on electrothermal interaction and is experimentally verified on a dedicated test structure. The presented results provide electrothermal insights in current power electronic technologies and emphasize their potential to further improve the robustness and reliability of next generation technologies.
- 7 July 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 31 (4) , 3128-3140
Electrothermal Multiscale Modeling and Simulation Concepts for Power Electronics
This paper presents a finite-element-based simulation methodology to improve on multiscale modeling and analysis limitations of power electronics development. The method utilizes homogenization and nonmatching grid concepts to offer a high degree of flexibility and reduce computational effort. The applied homogenization method provides effective material properties to realize full-chip modeling performance without the need to model geometric details. The concept of nonmatching grids allows the inclusion of a subregion with substantially finer mesh than its surrounding regions. This allows the flexible integration of micrometer scale geometries with a high degree of detail within the full-chip model. Both concepts are thoroughly introduced and an application to a state-of-the-art power electronics semiconductor technology is presented. This paper focuses on electrothermal interaction and is experimentally verified on a dedicated test structure. The presented results provide electrothermal insights in current power electronic technologies and emphasize their potential to further improve the robustness and reliability of next generation technologies.