SGSaikat Subhra Ghosh

Saikat Subhra Ghosh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Saikat Subhra Ghosh has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Nanocrystalline Powder Cores for High-Power High-Frequency Applications

    by Chaoqiang Jiang, Xinru Li, Saikat S. Ghosh, Hui Zhao, Yanfeng Shen, Teng Long

    Soft magnetic composites (SMCs) based magnetic cores are attractive for high frequency and high power inductor design. The permeability of SMC core can be achieved by adjusting the powder size, addition of insulation material, and forming pressure to reduce the air gap loss and ease the inductor design. The nanocrystalline alloy (Fe-Cu-Nb-Si-B) with high saturation flux density and low hysteresis loss, showing potential suitability for SMC based magnetic cores. To date, nanocrystalline alloys are mostly used in form of laminated ribbons for magnetic cores but seldom used in SMC cores. Neither experimental validation of nanocrystalline powder SMC cores nor comparison with other commonly used SMC cores has been reported. In this paper, the structure and manufacturing process of nanocrystalline powder cores are introduced. The calculation of core loss is defined for the nanocrystalline powder core. The characteristics and performance of the nanocrystalline powder toroidal core are compared with those of other SMC cores such as Fe-Si powder (X flux), Fe-Ni powder (High flux), Fe-Si-Al powder (Kool Mμ), Fe-Ni-Mo powder (MPP). Experimental results at frequencies from 100 kHz to 600 kHz are provided to validate the loss calculation and feasibility of this new nanocrystalline powder core.


  • Feasibility Study of Nanocrystalline-Ribbon Cores for Polarized Inductive Power Transfer Pads

    by Daniel E. Gaona, Saikat Subhra Ghosh, Teng Long

    MnZn-based ferrite materials like the EPCOS N87 or K2004 are commonly used as magnetic cores in inductive power transfer (IPT) applications. However, the performance and reliability of the IPT systems are limited by ferrite's intrinsic brittleness and low flux density saturation point. In this paper, a study of nanocrystalline ribbon based magnetic cores for IPT applications is presented. FEM simulations and experimental validations are used to compare both materials. The design of ultra-thin laminated cores such as nanocrystalline ribbons for IPT systems is presented. Compared to ferrite, nanocrystalline ribbon is mechanically more robust and it has higher magnetic permeability and a higher saturation point. Results show that nanocrystalline ribbon cores achieve more than 50% volume reduction of the IPT pads due to its high saturation point. However, a compromise arises as the total power loss increases due to the induced eddy currents in the core. The reduction of efficiency can be mitigated by special geometrical design of the nanocrystalline ribbon core. A 6.6 kW IPT system has been built for experimental validation of the design methodology.


  • Open Access

    Dual polarity DC–DC converter integrated grid‐tied single‐phase transformer less inverter for solar application

    by Saikat Subhra Ghosh, Kumaran S. Nathan, Yam P. Siwakoti, Teng Long

    This study proposes a novel single‐phase transformer‐less inverter, using the principle of combined Ćuk SEPIC (CCS) converter for grid‐connected photovoltaic (PV) systems. The new inverter has a common ground between the grid and the PV source, which helps to eliminate the leakage current for the grid‐connected PV application. Unlike common ground‐type charge‐pump‐based transformer‐less inverter, this topology eliminates inrush current and hence reduces the current stress on the components. The CCS allows voltage control with both step‐up and step‐down abilities, along with more robustness against solar panel side fault. Further, application of wide band‐gap devices, such as SiC MOSFETs allows higher switching frequency to be achieved, and thus reduction of the passive components. A novel switching strategy, proposed here allows current in both directions, positive and negative (to the load/grid or from the load/grid, for reactive loads), making the converter suitable for grid connection (unity power factor), as well as stand‐alone operation. The proposed concept has been discussed in detail, along with simulation results. Finally, a prototype hardware has been fabricated and the experimental results are reported.


  • Control Strategy for a Multiphase Lundell-Alternator/Active-Rectifier System in 14 V Automotive Power Systems

    by Dimitrios Sarafianos, Danilo X. Llano, Saikat S. Ghosh, Richard A. McMahon, Stephen Pickering, Timothy J. Flack

    This paper presents a novel control strategy for a conventional six-phase Lundell alternator fed at the output with a MOSFET-based active-rectifier. The signal references for the controller are calculated from a cost-function aiming to minimise the alternator stator copper losses in an effort to maximise the alternator-rectifier system overall efficiency. The system is initially simulated and tuned in Matlab/Simulink and then experimentally verified. Steady-state efficiency results from experimental measurements of the alternator/rectifier system are compared against a standard passive rectifier. The results indicate a better overall efficiency compared to the passive rectifier, for an alternator speed of up to approximately 5000 rpm, corresponding to city driving.


  • A New DC–DC Converter for Photovoltaic Systems: Coupled-Inductors Combined Cuk-SEPIC Converter

    by Kumaran Nathan, Saikat Ghosh, Yam Siwakoti, Teng Long

    An enhanced DC-DC converter is proposed in this paper, based on the combination of the Cuk and SEPIC converters, which is well-suited for solar photovoltaic (PV) applications. The converter uses only one switch (which is ground-referenced, so simple gate drive circuitry may be used), yet provides dual outputs in the form of a bipolar DC bus. The bipolar output from the DC-DC converter is able to send power to the grid via any inverter with a unipolar or bipolar DC input, and leakage currents can be eliminated if the latter type is used without using lossy DC capacitors in the load current loop. The proposed converter uses integrated magnetics cores to couple the input and output inductors, which significantly reduces the input current ripple and hence greatly improves the power extracted from the solar PV system. The design methodology along with simulation, experimental waveforms, and efficiency measurements of a 4-kW DC-DC converter are presented to prove the concept of the proposed converter. Furthermore, a 1-kW inverter is also developed to demonstrate the converter's grid-connection potential.


  • Open Access

    Integrated starter alternator sizing for micro / mild hybrid vehicle using Monte Carlo simulation

    by Saikat Subhra Ghosh, Timothy J. Flack, Teng Long

    The Integrated Starter Alternator (ISA) needs to cater for a very wide range of torque and speed, in both motor and generator modes and in different functionalities, such as engine starting, alternator, regenerative braking and torque boost. Furthermore, each of these functionalities, being dependent on the drive cycle, means that determining the optimal ISA torque-speed characteristics is a challenging problem. In this paper, a Monte-Carlo simulation has been reported to find the most frequently operated regions in the torque-speed plane of an ISA, using stochastic drive cycles. This has been used to determine the optimal torque-speed characteristic to inform the ISA design specification. In turn, this gives a more robust coverage of different driving patterns compared to a conventional driving cycle-based design.

  • Open Access

    Experimental characterisation and performance evaluation of a coaxial current transformer for measurement of insulated gate bipolar transistor switching current

    by Saikat Subhra Ghosh, Gopalaratnam Narayanan

    Measurement of device current during switching characterisation of an insulated gate bipolar transistor (IGBT) requires a current sensor with low insertion impedance and high bandwidth. This study presents an experimental procedure for evaluating the performance of a coaxial current transformer (CCT), designed for the above purpose. A prototype CCT, which can be mounted directly on a power terminal of a 1200 V/50 A half‐bridge IGBT module, is characterised experimentally. The measured characteristics include insertion impedance, gain and phase of the CCT at different frequencies. The bounds of linearity within which the CCT can operate without saturation are determined theoretically, and are also verified experimentally. The experimental study on linearity of the CCT requires a high‐amplitude current source. A proportional–resonant (PR) controller‐based current‐controlled half‐bridge inverter is developed for this purpose. A systematic procedure for selection of PR controller parameters is also reported in this study. This set‐up is helpful to determine the limit of linearity and also to measure the frequency response of the CCT at realistic amplitudes of current in the low‐frequency range.