Hidetoshi Oguro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hidetoshi Oguro has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Satoshi Awaji
Institute for Materials Research, Tohoku University
23 shared publications - Masahiro Sugimoto
Furukawa Electric Company Ltd., Nikko, Japan
7 shared publications Kazuo Watanabe
Institute for Materials Research, Tohoku University, Sendai, Japan
6 shared publications- Akihiro Kikuchi
National Institute for Materials Science (NIMS), Tsukuba, Japan
3 shared publications - Daisuke Asami
Superconducting products section, Furukawa Electric Co., Ltd., Nikko, Tochigi, Japan
3 shared publications - Gen Nishijima
National Institute for Materials Science (NIMS), Tsukuba, Japan
3 shared publications
Latest Publications
- Open Access
- 19 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Internal Strain Measurement by Neutron Diffraction Under Transverse Compressive Stress for Nb3Sn Wires With and Without Cu-Nb Reinforcement
For an accelerator magnet, a certain mechanical strength is required to sustain against a transverse compression stress due to Lorentz force. A bronze-route Nb 3 Sn wire with Cu-Nb reinforcement was developed by Tohoku University and Furukawa Electric to enhance the strength against axial tension. The Cu-Nb reinforcement wire also exhibited some indication of strength improvement against transverse compression; however, the details of a reinforcement mechanism for the transverse compression stress have not been clarified. In this study, the internal strains of Nb 3 Sn bronze-route wires with and without the Cu-Nb reinforcement under transverse compression stress were evaluated by neutron diffraction at BL19 (TAKUMI) in J-PARC. The samples were attached to jig with solder only at the ends and compression was applied at the center of the samples with 30-mm anvil with 5-mm wide and 8- to 15-mm high beam. Since a critical current, Ic of a superconducting wire depends on the three-dimensional strain, internal strain of Nb 3 Sn along the axial and two orthogonal radial directions were evaluated at room temperature (RT). In the different setup, Ic measurements of the wires under transverse compression stresses were also performed at 4.2 K and 14.5 T. Using 3-mm wide anvil, the transverse compression was applied at 4.2 K or RT. The neutron diffraction results indicated no significant differences in the internal strains of Nb 3 Sn under transverse compression between the samples with and without Cu-Nb reinforcement, while the Ic measurements showed potential increase in the irreversible stress ( σirr ) for Cu-Nb reinforced wires. The reason for this discrepancy was discussed based on the difference in the experimental setups for each measurement.
- 19 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Open AccessInternal Strain Measurement by Neutron Diffraction Under Transverse Compressive Stress for Nb3Sn Wires With and Without Cu-Nb Reinforcement
For an accelerator magnet, a certain mechanical strength is required to sustain against a transverse compression stress due to Lorentz force. A bronze-route Nb 3 Sn wire with Cu-Nb reinforcement was developed by Tohoku University and Furukawa Electric to enhance the strength against axial tension. The Cu-Nb reinforcement wire also exhibited some indication of strength improvement against transverse compression; however, the details of a reinforcement mechanism for the transverse compression stress have not been clarified. In this study, the internal strains of Nb 3 Sn bronze-route wires with and without the Cu-Nb reinforcement under transverse compression stress were evaluated by neutron diffraction at BL19 (TAKUMI) in J-PARC. The samples were attached to jig with solder only at the ends and compression was applied at the center of the samples with 30-mm anvil with 5-mm wide and 8- to 15-mm high beam. Since a critical current, Ic of a superconducting wire depends on the three-dimensional strain, internal strain of Nb 3 Sn along the axial and two orthogonal radial directions were evaluated at room temperature (RT). In the different setup, Ic measurements of the wires under transverse compression stresses were also performed at 4.2 K and 14.5 T. Using 3-mm wide anvil, the transverse compression was applied at 4.2 K or RT. The neutron diffraction results indicated no significant differences in the internal strains of Nb 3 Sn under transverse compression between the samples with and without Cu-Nb reinforcement, while the Ic measurements showed potential increase in the irreversible stress ( σirr ) for Cu-Nb reinforced wires. The reason for this discrepancy was discussed based on the difference in the experimental setups for each measurement.
- 7 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Advantages of Cu-Nb Reinforced Nb$_{\text{3}}$Sn Strands in Large Multi-Stage Stranded Cables With Low-Void Fraction
A large multi-stage stranded cable structure with Nb $_{\text{3}}$ Sn strands twisted at a short-pitch and compressed to a low-void fraction is a major candidate for Nb $_{\text{3}}$ Sn conductors for JA-DEMO-TF coils. To realize the conductor, we have proposed the application of Nb-rod-method Cu-Nb reinforced ITER-CS type Nb $_{\text{3}}$ Sn strands (Cu-Nb/Nb $_{\text{3}}$ Sn wires). Prototype 4th-stage stranded cables simulated the stranded process for the ITER-CS conductor and for the JA-DEMO-TF conductor were fabricated using the Cu-Nb/Nb $_{\text{3}}$ Sn strands or conventional non-reinforced ITER-CS strands (Cu/Nb $_{\text{3}}$ Sn wires), and compression-formed to a low-void fraction below 30%. Cu-Nb/Nb $_{\text{3}}$ Sn strands extracted from the compacted 4th-stage cables had no degradation of I c as well as Cu/Nb $_{\text{3}}$ Sn strands. Destructive investigation of the compacted 4th-stage cables showed Cu-Nb/Nb $_{\text{3}}$ Sn cables had better manufacturability of the large multi-stage stranded cables with low-void fraction than the conventional Cu/Nb $_{\text{3}}$ Sn cables. Moreover, the Cu-Nb/Nb $_{\text{3}}$ Sn triplex had improved current-carrying properties under transverse compression stresses by enhancement of the mechanical properties. In this study, the advantages of applying Cu-Nb/Nb $_{\text{3}}$ Sn strands for the large multi-stage stranded cables with low-void fraction are discussed.
- 7 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-6
Advantages of Cu-Nb Reinforced Nb$_{\text{3}}$Sn Strands in Large Multi-Stage Stranded Cables With Low-Void Fraction
A large multi-stage stranded cable structure with Nb $_{\text{3}}$ Sn strands twisted at a short-pitch and compressed to a low-void fraction is a major candidate for Nb $_{\text{3}}$ Sn conductors for JA-DEMO-TF coils. To realize the conductor, we have proposed the application of Nb-rod-method Cu-Nb reinforced ITER-CS type Nb $_{\text{3}}$ Sn strands (Cu-Nb/Nb $_{\text{3}}$ Sn wires). Prototype 4th-stage stranded cables simulated the stranded process for the ITER-CS conductor and for the JA-DEMO-TF conductor were fabricated using the Cu-Nb/Nb $_{\text{3}}$ Sn strands or conventional non-reinforced ITER-CS strands (Cu/Nb $_{\text{3}}$ Sn wires), and compression-formed to a low-void fraction below 30%. Cu-Nb/Nb $_{\text{3}}$ Sn strands extracted from the compacted 4th-stage cables had no degradation of I c as well as Cu/Nb $_{\text{3}}$ Sn strands. Destructive investigation of the compacted 4th-stage cables showed Cu-Nb/Nb $_{\text{3}}$ Sn cables had better manufacturability of the large multi-stage stranded cables with low-void fraction than the conventional Cu/Nb $_{\text{3}}$ Sn cables. Moreover, the Cu-Nb/Nb $_{\text{3}}$ Sn triplex had improved current-carrying properties under transverse compression stresses by enhancement of the mechanical properties. In this study, the advantages of applying Cu-Nb/Nb $_{\text{3}}$ Sn strands for the large multi-stage stranded cables with low-void fraction are discussed.
- 29 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Melt Growth of YBa2Cu3O7-δ by Using BaCu2O2 and Y2BaCuO5 in Ag-Sheath
REBa 2 Cu 3 O 7-δ (REBCO; RE = Y or rare earth) wires with high critical current density ( J c ) are developed as coated conductors because REBCO crystals must be oriented to achieve high J c . To create biaxially textured REBCO films, REBCO is deposited as a thin film on an oriented substrate. However, REBCO-coated conductors exhibit problems of hotspots, delamination etc. Because these problems can be eliminated in round wires, the development of round REBCO wires is necessary. Silver is a suitable sheath material for Powder-in-Tube (PIT)-processed REBCO wires because it does not react with REBCO, is not oxidized at high temperatures in the air, and is permeable to oxygen. In addition, the melting point of silver is 961 °C, which is lower than that of YBa 2 Cu 3 O 7-δ (1000 °C). However, with other materials having low melting points, the melt growth method must be used. In this study, BaCu 2 O 2 and Y 2 BaCuO 5 were prepared as raw materials to fabricate round YBCO wires. The melting point of BaCu 2 O 2 is approximately 880 °C in low oxygen partial pressure. A round wire comprising BaCu 2 O 2 and Y 2 BaCuO 5 was fabricated by utilizing the PIT method. Microstructural observation and measurement of superconducting properties were performed. The critical current density of the wire reached 5200 A/cm 2 at 4.2K in self-field.
- 29 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Melt Growth of YBa2Cu3O7-δ by Using BaCu2O2 and Y2BaCuO5 in Ag-Sheath
REBa 2 Cu 3 O 7-δ (REBCO; RE = Y or rare earth) wires with high critical current density ( J c ) are developed as coated conductors because REBCO crystals must be oriented to achieve high J c . To create biaxially textured REBCO films, REBCO is deposited as a thin film on an oriented substrate. However, REBCO-coated conductors exhibit problems of hotspots, delamination etc. Because these problems can be eliminated in round wires, the development of round REBCO wires is necessary. Silver is a suitable sheath material for Powder-in-Tube (PIT)-processed REBCO wires because it does not react with REBCO, is not oxidized at high temperatures in the air, and is permeable to oxygen. In addition, the melting point of silver is 961 °C, which is lower than that of YBa 2 Cu 3 O 7-δ (1000 °C). However, with other materials having low melting points, the melt growth method must be used. In this study, BaCu 2 O 2 and Y 2 BaCuO 5 were prepared as raw materials to fabricate round YBCO wires. The melting point of BaCu 2 O 2 is approximately 880 °C in low oxygen partial pressure. A round wire comprising BaCu 2 O 2 and Y 2 BaCuO 5 was fabricated by utilizing the PIT method. Microstructural observation and measurement of superconducting properties were performed. The critical current density of the wire reached 5200 A/cm 2 at 4.2K in self-field.
- Open Access
- 1 January 2024
- Published by Society of Advanced Science in Journal of Advanced Science
- Vol. 36, 36109
Development of high critical current density YBCO high temperature superconducting round wire
YBa2Cu3O7-ẟ (YBCO) round wires with high critical current density (Jc) were developed by the Powder—in—Tube method and melt—growth process. For the sheath material of the wire, silver was selected since it doesn’t react with YBCO, it is not oxidized at high temperatures in the air, and it is permeable to oxygen. Since BaCu2O2 has a melting point of 880°C, which is lower than silver, BaCu2O2 and Y2BaCuO5 were prepared as raw materials. The YBCO round wire was developed by melt-growth process in oxygen pressure control condition. After the heat-treatment, large YBCO grains were observed. The critical current density of the wire reached 46 kA⁄cm2 at 4.2 K in self-field and 33 kA⁄cm2 in 14 T. Unfortunately, since current sharing through the silver occurred during the measurements, the exact Ic should be evaluated.
- 1 January 2024
- Published by Society of Advanced Science in Journal of Advanced Science
- Vol. 36, 36109
Open AccessDevelopment of high critical current density YBCO high temperature superconducting round wire
YBa2Cu3O7-ẟ (YBCO) round wires with high critical current density (Jc) were developed by the Powder—in—Tube method and melt—growth process. For the sheath material of the wire, silver was selected since it doesn’t react with YBCO, it is not oxidized at high temperatures in the air, and it is permeable to oxygen. Since BaCu2O2 has a melting point of 880°C, which is lower than silver, BaCu2O2 and Y2BaCuO5 were prepared as raw materials. The YBCO round wire was developed by melt-growth process in oxygen pressure control condition. After the heat-treatment, large YBCO grains were observed. The critical current density of the wire reached 46 kA⁄cm2 at 4.2 K in self-field and 33 kA⁄cm2 in 14 T. Unfortunately, since current sharing through the silver occurred during the measurements, the exact Ic should be evaluated.
- 15 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Development of Cu-Nb Reinforced Nb3Sn Wires Appropriate for Large Multi-Stage Stranded Cables With Short-Pitch Twisting and Low-Void Ratio
The strength of the conventional Cu/Nb 3 Sn wires may be too low to be applied to much larger cable-in-conduit (CIC) conductors with the multi-stranded cable structure of short-pitch twisting and low-void ratio applied for ITER-CS conductors. In this study, the Nb-rod-method Cu-Nb reinforced ITER-type Nb 3 Sn wire was developed by using a bronze-process not only to realize superior superconducting properties under high electromagnetic stresses but also to mitigate damage to the superconducting wires during the cable manufacturing process. The critical current properties of the Cu-Nb/Nb 3 Sn wire were significantly higher performance under both tensile stress and transverse compression stress compared to a conventional non-reinforced Cu/Nb 3 Sn wire. The Cu-Nb reinforcement had no detrimental effect on the AC losses of the wire. The trial production of short-pitch sub-cables was conducted, and it was confirmed that the Cu-Nb/Nb 3 Sn wires can improve the manufacturability of multi-stage stranded cables co-twisted with copper wires.
- 15 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Development of Cu-Nb Reinforced Nb3Sn Wires Appropriate for Large Multi-Stage Stranded Cables With Short-Pitch Twisting and Low-Void Ratio
The strength of the conventional Cu/Nb 3 Sn wires may be too low to be applied to much larger cable-in-conduit (CIC) conductors with the multi-stranded cable structure of short-pitch twisting and low-void ratio applied for ITER-CS conductors. In this study, the Nb-rod-method Cu-Nb reinforced ITER-type Nb 3 Sn wire was developed by using a bronze-process not only to realize superior superconducting properties under high electromagnetic stresses but also to mitigate damage to the superconducting wires during the cable manufacturing process. The critical current properties of the Cu-Nb/Nb 3 Sn wire were significantly higher performance under both tensile stress and transverse compression stress compared to a conventional non-reinforced Cu/Nb 3 Sn wire. The Cu-Nb reinforcement had no detrimental effect on the AC losses of the wire. The trial production of short-pitch sub-cables was conducted, and it was confirmed that the Cu-Nb/Nb 3 Sn wires can improve the manufacturability of multi-stage stranded cables co-twisted with copper wires.
- 20 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-4
Evaluation of Critical Current for REBCO Coated Conductor Under Various Tensile Strains and Magnetic Field Angles
REBa 2 Cu 3 O x (REBCO, RE: Y or rare-earth element) coated conductors (CCs) have a high critical current ( I c ) density in a high magnetic field at low temperatures. Therefore, REBCO CCs are being studied for high-magnetic-field applications. I c of REBCO CCs varies with the field angle and strain. The mechanism of the strain effect on the superconducting properties of REBCO CC is unclear. Thus, in this study, the relationship between the strain and other parameters for REBCO was studied to understand the strain effect of REBCO CC. The angular dependence of I c for the REBCO CC under various tensile strains was investigated. A compact tensile testing apparatus for large transport-current measurements was developed. The field angular dependences of I c for the REBCO CC were measured at a temperature of 77.3 K and magnetic field of 0.4 T, under several tensile strains. The I c of the REBCO CC decreased due to the tensile strains at all field angles. The degradation was described by the strain effect of I c as the magnetic fields parallel to the c-axis and the ab-plane varied with respect to the tensile strain. These results suggest that strains can control the variation in I c and possibly the anisotropy of REBCO in the directions of the c-axis and ab-plane.
- 20 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-4
Evaluation of Critical Current for REBCO Coated Conductor Under Various Tensile Strains and Magnetic Field Angles
REBa 2 Cu 3 O x (REBCO, RE: Y or rare-earth element) coated conductors (CCs) have a high critical current ( I c ) density in a high magnetic field at low temperatures. Therefore, REBCO CCs are being studied for high-magnetic-field applications. I c of REBCO CCs varies with the field angle and strain. The mechanism of the strain effect on the superconducting properties of REBCO CC is unclear. Thus, in this study, the relationship between the strain and other parameters for REBCO was studied to understand the strain effect of REBCO CC. The angular dependence of I c for the REBCO CC under various tensile strains was investigated. A compact tensile testing apparatus for large transport-current measurements was developed. The field angular dependences of I c for the REBCO CC were measured at a temperature of 77.3 K and magnetic field of 0.4 T, under several tensile strains. The I c of the REBCO CC decreased due to the tensile strains at all field angles. The degradation was described by the strain effect of I c as the magnetic fields parallel to the c-axis and the ab-plane varied with respect to the tensile strain. These results suggest that strains can control the variation in I c and possibly the anisotropy of REBCO in the directions of the c-axis and ab-plane.
- 25 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-4
Jc Performance Under Transverse Compressive Stress of Internal Matrix Reinforced Nb3Sn Multifilamentary Wires Using Various Ternary Bronze Alloys
We approached internal matrix reinforcement using Cu-Sn-Zn and Cu-Sn-In ternary bronze alloy matrices for enhancing the effective mechanical strength of Nb 3 Sn wire. In this study, we evaluated the critical current density ( Jc ) degradation due to transverse compressive stress on internal matrix reinforced Nb 3 Sn multifilamentary wires using these ternary bronze alloy matrices, and the effects of both Zn and In solute element on the changes of Jc property under compressive stress was investigated. In the cases of internal matrix reinforced Nb 3 Sn wires using the Cu-Sn-Zn and Cu-Sn-In ternary alloy matrices, no Jc degradation was observed within 100 MPa of the transverse compressive stress. The (Cu, Zn) and (Cu, In) solid solution matrices contributed to suppressing Jc degradation by the compressive stress. In addition, the In element was the more effective solute element in the ternary alloy matrix on the internal matrix reinforcement based on the irreversible compressive stress estimated by the loading-unloading test.
- 25 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-4
Jc Performance Under Transverse Compressive Stress of Internal Matrix Reinforced Nb3Sn Multifilamentary Wires Using Various Ternary Bronze Alloys
We approached internal matrix reinforcement using Cu-Sn-Zn and Cu-Sn-In ternary bronze alloy matrices for enhancing the effective mechanical strength of Nb 3 Sn wire. In this study, we evaluated the critical current density ( Jc ) degradation due to transverse compressive stress on internal matrix reinforced Nb 3 Sn multifilamentary wires using these ternary bronze alloy matrices, and the effects of both Zn and In solute element on the changes of Jc property under compressive stress was investigated. In the cases of internal matrix reinforced Nb 3 Sn wires using the Cu-Sn-Zn and Cu-Sn-In ternary alloy matrices, no Jc degradation was observed within 100 MPa of the transverse compressive stress. The (Cu, Zn) and (Cu, In) solid solution matrices contributed to suppressing Jc degradation by the compressive stress. In addition, the In element was the more effective solute element in the ternary alloy matrix on the internal matrix reinforcement based on the irreversible compressive stress estimated by the loading-unloading test.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (5) , 1-5
Development of High-Performance Cu-Nb/Nb3Sn Wires for Various High Field Magnets
The bronze processed Nb3Sn wires strengthened with the Nb-rod-method Cu-Nb stabilizing reinforcer have excellent mechanical strength and a large compressive residual strain at both low temperatures and room temperatures after Nb3Sn reaction heat treatment. Therefore, the Cu-Nb/Nb3Sn wires are able to be applied to the high field superconducting magnet manufacturing by techniques of the React-and-Wind (R&W) and realize the higher irreversible strain. The characteristics such as the critical current density and the strength of Cu-Nb/Nb3Sn wires are designed to meet the required specifications by selecting tin content in the bronze, Nb volume ratio in the Cu-Nb composites, and the Cu-Nb volume ratio. For the R&W process, appropriate pre-bending treatments are applied to optimize the Ic properties under various stresses. In this study, a round Cu-Nb/Nb3Sn wire design was optimized for high-strength Rutherford cables used under high tensile stress over 300 MPa by composing of Cu-15.7wt%Sn-0.3wt%Ti and Cu-30vol%Nb stabilizing reinforcer. Moreover, a R&W-type Cu-Nb/Nb3Sn rectangular wire was proposed to improve the performance of the ultra-high field NMR coils.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (5) , 1-5
Development of High-Performance Cu-Nb/Nb3Sn Wires for Various High Field Magnets
The bronze processed Nb3Sn wires strengthened with the Nb-rod-method Cu-Nb stabilizing reinforcer have excellent mechanical strength and a large compressive residual strain at both low temperatures and room temperatures after Nb3Sn reaction heat treatment. Therefore, the Cu-Nb/Nb3Sn wires are able to be applied to the high field superconducting magnet manufacturing by techniques of the React-and-Wind (R&W) and realize the higher irreversible strain. The characteristics such as the critical current density and the strength of Cu-Nb/Nb3Sn wires are designed to meet the required specifications by selecting tin content in the bronze, Nb volume ratio in the Cu-Nb composites, and the Cu-Nb volume ratio. For the R&W process, appropriate pre-bending treatments are applied to optimize the Ic properties under various stresses. In this study, a round Cu-Nb/Nb3Sn wire design was optimized for high-strength Rutherford cables used under high tensile stress over 300 MPa by composing of Cu-15.7wt%Sn-0.3wt%Ti and Cu-30vol%Nb stabilizing reinforcer. Moreover, a R&W-type Cu-Nb/Nb3Sn rectangular wire was proposed to improve the performance of the ultra-high field NMR coils.
- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Electromechanical Properties Evaluation of Multifilamentary MgB2 Wires With Different Reinforcements
Magnesium diboride ( ${\rm{MgB_{2}}}$ ) wires are highly attractive for various applications, given their high critical transition temperatures. The brittle compound filaments are protected by metallic sheaths that provide sufficiently strong reinforcement. The mechanical reinforcement provided to the brittle wires compensates for this weakness and enhances their electromechanical properties. Therefore, ${\rm{MgB_{2}}}$ wires can be considered a promising alternative to high-temperature superconducting wires in low magnetic fields such as those used in magnetic resonance imaging, wind power generators, and other applications. This study focused on the evaluation of the electromechanical behaviors of multifilamentary ${\rm{MgB_{2}}}$ wires of various configurations and with various sheaths. The irreversible strain/stress limits for ${I_{c}}$ degradation were evaluated under practical environmental conditions at a magnetic field of 2 T and a temperature of 20 K. The influences of the reinforcing materials on the electromechanical properties were investigated as was the temperature dependence of the mechanical properties.- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Electromechanical Properties Evaluation of Multifilamentary MgB2 Wires With Different Reinforcements
Magnesium diboride ( ${\rm{MgB_{2}}}$ ) wires are highly attractive for various applications, given their high critical transition temperatures. The brittle compound filaments are protected by metallic sheaths that provide sufficiently strong reinforcement. The mechanical reinforcement provided to the brittle wires compensates for this weakness and enhances their electromechanical properties. Therefore, ${\rm{MgB_{2}}}$ wires can be considered a promising alternative to high-temperature superconducting wires in low magnetic fields such as those used in magnetic resonance imaging, wind power generators, and other applications. This study focused on the evaluation of the electromechanical behaviors of multifilamentary ${\rm{MgB_{2}}}$ wires of various configurations and with various sheaths. The irreversible strain/stress limits for ${I_{c}}$ degradation were evaluated under practical environmental conditions at a magnetic field of 2 T and a temperature of 20 K. The influences of the reinforcing materials on the electromechanical properties were investigated as was the temperature dependence of the mechanical properties.- 18 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Mechanical Strength Evaluation of the Internal Matrix Reinforced Nb3Sn Multifilamentary Wires Using Cu–Sn–In Ternary Alloy Matrix
We investigated the simple internal reinforcement meth-od using special reinforcement ternary bronze alloy matrix on the bronze processed $\text{NB}_3\text{Sn}$ wire. The Cu-Sn-Zn ternary alloy ma-trix was transformed to the (Cu, Zn) solid solution after $\text{NB}_3\text{Sn}$ synthesis based on the solid solution strengthening mechanism. For the further mechanical strength improvement, we focused on the Indium (In) as the more effective solute element for the "internal matrix strengthening", and succeeded to fabricate the bronze processed $\text{NB}_3\text{Sn}$ multifilamentary wire using various Cu-Sn-In-(Ti) ternary alloy matrices. Changes of the Vickers hardness before and after $\text{NB}_3\text{Sn}$ syn-thesis and the transport critical current ( $I_c$ ) under the uniaxial tensile deformation were evaluated. Vickers hardness of the ma-trix after $\text{NB}_3\text{Sn}$ synthesis on the Cu-Sn-In ternary alloy matrix samples was higher compared with the conventional bronze and the Cu-Sn-Zn ternary matrix samples. On the other hand, the tensile stress obtained to the maximum peak $I_c$ value on the Cu-Sn-In ternary alloy matrix sample was estimated to approximately 265 MPa, and this value was much higher than those of the Cu-Sn-Zn ternary matrix and conventional bronze processed samples. We found that the In element would become more attractive solute element than Zn element for the internal rein-forcement ternary matrix.- 18 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Mechanical Strength Evaluation of the Internal Matrix Reinforced Nb3Sn Multifilamentary Wires Using Cu–Sn–In Ternary Alloy Matrix
We investigated the simple internal reinforcement meth-od using special reinforcement ternary bronze alloy matrix on the bronze processed $\text{NB}_3\text{Sn}$ wire. The Cu-Sn-Zn ternary alloy ma-trix was transformed to the (Cu, Zn) solid solution after $\text{NB}_3\text{Sn}$ synthesis based on the solid solution strengthening mechanism. For the further mechanical strength improvement, we focused on the Indium (In) as the more effective solute element for the "internal matrix strengthening", and succeeded to fabricate the bronze processed $\text{NB}_3\text{Sn}$ multifilamentary wire using various Cu-Sn-In-(Ti) ternary alloy matrices. Changes of the Vickers hardness before and after $\text{NB}_3\text{Sn}$ syn-thesis and the transport critical current ( $I_c$ ) under the uniaxial tensile deformation were evaluated. Vickers hardness of the ma-trix after $\text{NB}_3\text{Sn}$ synthesis on the Cu-Sn-In ternary alloy matrix samples was higher compared with the conventional bronze and the Cu-Sn-Zn ternary matrix samples. On the other hand, the tensile stress obtained to the maximum peak $I_c$ value on the Cu-Sn-In ternary alloy matrix sample was estimated to approximately 265 MPa, and this value was much higher than those of the Cu-Sn-Zn ternary matrix and conventional bronze processed samples. We found that the In element would become more attractive solute element than Zn element for the internal rein-forcement ternary matrix.