Arkadiusz Szymanek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Arkadiusz Szymanek has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Agnieszka Bala-Litwiniak
Department of Production Management, Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Armii Krajowej 19, 42-200 Czestochowa, Poland
1 shared publication - Anna Pajdak
Strata Mechanics Research Institute of the Polish Academy of Sciences, Krakow, Poland
1 shared publication - Dorota Musiał
Department of Production Management, Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Armii Krajowej 19, 42-200 Czestochowa, Poland
1 shared publication - Magdalena Szwaja
Department of Thermal Machinery, Faculty of Mechanical Engineering and Computer Science, Czestochowa University of Technology, Dabrowskiego 69, 42-200 Czestochowa, Poland
1 shared publication - Michał Nabiałczyk
Department of Production Management, Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Armii Krajowej 19, 42-200 Czestochowa, Poland
1 shared publication - Przemysław Szymanek1 shared publication
Latest Publications
- Open Access
Walnut Shell Pretreatment in Regard to Its Combustion Properties
Shortages in the energy market for traditional fuels, rising prices, and the requirements placed on member states by the European Union to reduce greenhouse gas (GHG) emissions are resulting in an increased interest in alternative energy sources. One such source is waste biomass. This biomass is not only ecological and publicly available, but, unlike other sources of renewable energy, it is independent of weather conditions or terrain. Unfortunately, despite the enormous potential, only a few types of biomass are currently used in the energy and heating industries. To change this, a material in the form of a walnut shell that has not been used in this field before is examined. In this work, pellets made from walnut shells were analyzed for combustion in heating boilers intended for this kind of fuel, commonly used in many households. The produced pellet was subjected to a combustion process, and the emitted flue gases were analyzed to check the suitability of the fuel for the heat-generating purpose. The exhaust gas was analyzed for the presence of compounds such as CO, NOx, CH4, and H2S. In addition, a series of tests were conducted to determine how the drying process time and temperature of the biomass affect its subsequent heating value. As a result of this research, it was proven that the walnut shell is suitable for the production of pellets, thus obtaining high results for a calorific value of 16.90 MJ/kg, an ash content of 1.31%, and a moisture content of 8.25%. Thanks to the obtained results, it was concluded that the produced fuel can be compared with commercial pellets, as it does not differ from and even exceeds some of the values of fuels currently available on the market. The temperature and time during the drying of the biomass also showed correlations with the subsequent calorific value of the material, with a temperature of 110 °C and a time period of 90 min providing the best results.
Open AccessWalnut Shell Pretreatment in Regard to Its Combustion Properties
Shortages in the energy market for traditional fuels, rising prices, and the requirements placed on member states by the European Union to reduce greenhouse gas (GHG) emissions are resulting in an increased interest in alternative energy sources. One such source is waste biomass. This biomass is not only ecological and publicly available, but, unlike other sources of renewable energy, it is independent of weather conditions or terrain. Unfortunately, despite the enormous potential, only a few types of biomass are currently used in the energy and heating industries. To change this, a material in the form of a walnut shell that has not been used in this field before is examined. In this work, pellets made from walnut shells were analyzed for combustion in heating boilers intended for this kind of fuel, commonly used in many households. The produced pellet was subjected to a combustion process, and the emitted flue gases were analyzed to check the suitability of the fuel for the heat-generating purpose. The exhaust gas was analyzed for the presence of compounds such as CO, NOx, CH4, and H2S. In addition, a series of tests were conducted to determine how the drying process time and temperature of the biomass affect its subsequent heating value. As a result of this research, it was proven that the walnut shell is suitable for the production of pellets, thus obtaining high results for a calorific value of 16.90 MJ/kg, an ash content of 1.31%, and a moisture content of 8.25%. Thanks to the obtained results, it was concluded that the produced fuel can be compared with commercial pellets, as it does not differ from and even exceeds some of the values of fuels currently available on the market. The temperature and time during the drying of the biomass also showed correlations with the subsequent calorific value of the material, with a temperature of 110 °C and a time period of 90 min providing the best results.
- Open Access
- 4 August 2023
- Published by Polish Scientific Society of Combustion Engines in Combustion Engines
Combustion comparative analysis of pyrolysis oil and diesel fuel under constant-volume conditions
The article discusses the research results on the combustion of pyrolysis oil derived from the pyrolysis of HDPE plastics after its distillation. The tests were carried out in a constant-volume combustion chamber in conditions similar to those in a compression-ignition engine with a compression ratio of 17.5:1. The phases of premixed and diffusion combustion and the ignition lag were determined. Diesel fuel combustion tests were performed under similar pressure-temperature conditions. Comparative analysis was used to draw conclusions as follows: the duration of the premixed combustion phase for pyrolysis oil is approximately 5% shorter than that for diesel oil; with an increase in the initial pressure in the chamber, the premixed combustion time in both cases was shortened, while the diffusion combustion time slightly increased, practically without any significant change; the maximum combustion rate for the premixed combustion phase for pyrolysis oil was nearly 20% higher than that for diesel fuel; the heat released from the premixed combustion phase for pyrolysis oil was found to be 20% higher compared to that one for diesel fuel; the ignition lag for pyrolysis oil was slightly longer compared to that for diesel fuel. The presented parameters significantly impact both the development of combustion and the thermal efficiency of the internal combustion engine. Summing up, pyrolysis oil can be applied as a substitute for diesel fuel as a single or blended component with it.
- 4 August 2023
- Published by Polish Scientific Society of Combustion Engines in Combustion Engines
Open AccessCombustion comparative analysis of pyrolysis oil and diesel fuel under constant-volume conditions
The article discusses the research results on the combustion of pyrolysis oil derived from the pyrolysis of HDPE plastics after its distillation. The tests were carried out in a constant-volume combustion chamber in conditions similar to those in a compression-ignition engine with a compression ratio of 17.5:1. The phases of premixed and diffusion combustion and the ignition lag were determined. Diesel fuel combustion tests were performed under similar pressure-temperature conditions. Comparative analysis was used to draw conclusions as follows: the duration of the premixed combustion phase for pyrolysis oil is approximately 5% shorter than that for diesel oil; with an increase in the initial pressure in the chamber, the premixed combustion time in both cases was shortened, while the diffusion combustion time slightly increased, practically without any significant change; the maximum combustion rate for the premixed combustion phase for pyrolysis oil was nearly 20% higher than that for diesel fuel; the heat released from the premixed combustion phase for pyrolysis oil was found to be 20% higher compared to that one for diesel fuel; the ignition lag for pyrolysis oil was slightly longer compared to that for diesel fuel. The presented parameters significantly impact both the development of combustion and the thermal efficiency of the internal combustion engine. Summing up, pyrolysis oil can be applied as a substitute for diesel fuel as a single or blended component with it.
- 29 March 2019
- Published by Instytut Gospodarki Surowcami Mineralnymi i Energia Polskiej Akademii Nauk in Polityka Energetyczna – Energy Policy Journal
- Vol. 22 (1) , 113-126
Impact of magnetic fuel activators on the combustion process in metallurgical heating furnaces
The article presents the results of tests of the application of magnetic fuel activators, which improve the efficiency of metallurgical furnaces and positively affect the ecological aspects of their work. Energy indicators for metallurgical furnaces during operation before and after installation...
- 29 March 2019
- Published by Instytut Gospodarki Surowcami Mineralnymi i Energia Polskiej Akademii Nauk in Polityka Energetyczna – Energy Policy Journal
- Vol. 22 (1) , 113-126
Impact of magnetic fuel activators on the combustion process in metallurgical heating furnaces
The article presents the results of tests of the application of magnetic fuel activators, which improve the efficiency of metallurgical furnaces and positively affect the ecological aspects of their work. Energy indicators for metallurgical furnaces during operation before and after installation...