Klaus Solbach
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Klaus Solbach has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Thomas Kaiser
Institute of Digital Signal Processing, University of Duisburg-Essen, 47057 Duisburg, Germany
12 shared publications - Ali Alhaj Abbas
Interdisciplinary Research Center for Communication Systems and Sensing, King Fahd University of Petroleum & Minerals, Dhahran, Saudi Arabia
9 shared publications - Mohammed El-Absi
Institute of Digital Signal Processing, University of Duisburg-Essen, 47057 Duisburg, Germany
6 shared publications - Ashraf Abuelhaija
Applied Science Private University
5 shared publications - Feng Zheng
Institute of Digital Signal Processing, University of Duisburg-Essen, Duisburg, Germany
4 shared publications - Jahangir Alam
Institute of Digital-Signal Processing, University of Duisburg-Essen, 47057 Duisburg, Germany
3 shared publications
Latest Publications
- Open Access
Clutter Effect Investigation on Co-Polarized Chipless RFID Tags and Mitigation Using Cross-Polarized Tags, Analytical Model, Simulation, and Measurement
Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector (). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This extensive mathematical model developed for linear chipless RFID systems in clutter scenarios holds the potential to greatly assist researchers in their exploration of RCS-based tags. By relying solely on simulations, this model provides a tool to effectively analyze and understand RCS-based tags, ultimately simplifying the process of generating more authentic tag designs. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects.Open AccessClutter Effect Investigation on Co-Polarized Chipless RFID Tags and Mitigation Using Cross-Polarized Tags, Analytical Model, Simulation, and Measurement
Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector (). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This extensive mathematical model developed for linear chipless RFID systems in clutter scenarios holds the potential to greatly assist researchers in their exploration of RCS-based tags. By relying solely on simulations, this model provides a tool to effectively analyze and understand RCS-based tags, ultimately simplifying the process of generating more authentic tag designs. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects. - 4 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Radio Frequency Identification
- Vol. 7, 451-462
Photonic-Crystal-Resonator-Based Corner Reflector With Angle-of-Arrival Sensing
In this paper, we propose a Photonic Crystal (PhC) resonator based corner reflector for sensing the Angle-of-Arrival (AoA) of the incident wave from an interrogator. The sensor is constructed of joining a flat metal plate with a one-dimensional PhC resonator at an angle of 90∘. The PhC resonator is designed by inserting a defect layer between two quarter-wave Bragg mirrors in order to create a deep notch in the backscattering. While the PhC resonator provides unique spectral signatures in the “specular direction” related to AoA (i.e. by shifting the notch position), the corner configuration allows the back-scattering of these signatures to the direction of the interrogator. As a proof of concept, EM simulation and measurement are performed in W-band on a 40-mm squared PhC resonator perpendicularly joined with a same size metal plate. Based on signatures, a resolution of less than 6∘ can be achieved in the angular range -35∘ to 35∘. Due to the corner configuration that allows a high Radar Cross Section (RCS), the proposed sensor shows the potential of sensing the AoA at long reading ranges.
- 4 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Radio Frequency Identification
- Vol. 7, 451-462
Photonic-Crystal-Resonator-Based Corner Reflector With Angle-of-Arrival Sensing
In this paper, we propose a Photonic Crystal (PhC) resonator based corner reflector for sensing the Angle-of-Arrival (AoA) of the incident wave from an interrogator. The sensor is constructed of joining a flat metal plate with a one-dimensional PhC resonator at an angle of 90∘. The PhC resonator is designed by inserting a defect layer between two quarter-wave Bragg mirrors in order to create a deep notch in the backscattering. While the PhC resonator provides unique spectral signatures in the “specular direction” related to AoA (i.e. by shifting the notch position), the corner configuration allows the back-scattering of these signatures to the direction of the interrogator. As a proof of concept, EM simulation and measurement are performed in W-band on a 40-mm squared PhC resonator perpendicularly joined with a same size metal plate. Based on signatures, a resolution of less than 6∘ can be achieved in the angular range -35∘ to 35∘. Due to the corner configuration that allows a high Radar Cross Section (RCS), the proposed sensor shows the potential of sensing the AoA at long reading ranges.
- Open Access
- 13 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 71811-71822
A Mathematical Framework, Simulation, and Measurement of Harmonic Identification Systems
The main focus of this research paper is to develop a realistic mathematical framework to accurately characterize the performance of the harmonic identification system. This mathematical framework incorporates the essential factors that affect the harmonic identification system such as, the radiation pattern and polarization of the reader and transponder antennas, the angle of incidence and reflection, conversion efficiency of the non-linear element, besides the environmental effects which are multipath and clutter reflections. To validate the proposed analytical model, simulations and measurements are conducted using a state-of-the-art transponder equipped with a Schottky diode that exhibits non-linear characteristics in output power. The performance of the transponder is evaluated in both scenarios, with and without environmental reflections, where a significant drop in the backscattered signal is observed due to the multipath reflections. Accordingly, a Ray-tracing model is utilized to investigate the environmental reflections, and thus the system performance could be evaluated analytically. The close agreement between the results obtained from developed analytical framework and Ray-tracing simulations together with the corresponding measurements demonstrate the effectiveness of the proposed analytical framework in accurately predicting the performance of the harmonic identification systems.
- 13 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 71811-71822
Open AccessA Mathematical Framework, Simulation, and Measurement of Harmonic Identification Systems
The main focus of this research paper is to develop a realistic mathematical framework to accurately characterize the performance of the harmonic identification system. This mathematical framework incorporates the essential factors that affect the harmonic identification system such as, the radiation pattern and polarization of the reader and transponder antennas, the angle of incidence and reflection, conversion efficiency of the non-linear element, besides the environmental effects which are multipath and clutter reflections. To validate the proposed analytical model, simulations and measurements are conducted using a state-of-the-art transponder equipped with a Schottky diode that exhibits non-linear characteristics in output power. The performance of the transponder is evaluated in both scenarios, with and without environmental reflections, where a significant drop in the backscattered signal is observed due to the multipath reflections. Accordingly, a Ray-tracing model is utilized to investigate the environmental reflections, and thus the system performance could be evaluated analytically. The close agreement between the results obtained from developed analytical framework and Ray-tracing simulations together with the corresponding measurements demonstrate the effectiveness of the proposed analytical framework in accurately predicting the performance of the harmonic identification systems.
- Open Access
- 11 July 2023
- Published by MDPI AG in Preprints.org
Clutter Effect Investigation on Co-Polarized Chipless RFID Tags and Mitigation Using Cross-Polarized Tags, Analytical Model, Simulation, and Measurement
Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector (30.5cm×22.5cm). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects.
- 11 July 2023
- Published by MDPI AG in Preprints.org
Open AccessClutter Effect Investigation on Co-Polarized Chipless RFID Tags and Mitigation Using Cross-Polarized Tags, Analytical Model, Simulation, and Measurement
Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector (30.5cm×22.5cm). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects.
- 6 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (12) , 5291-5299
Retrodirective Dielectric Resonator Tag With Polarization Twist Signature for Clutter Suppression in Self-Localization System
In a recently proposed indoor self-localization system, we excite dielectric resonators (DRs) in linear polarization (LP) as retrodirective passive tags, either as single DR, small array of DRs, or in combination with a spherical dielectric lens. DR tags mounted close to a reflecting wall suffer from large clutter return, which can supercede the DR tag signatures. To separate both into orthogonal polarizations, we design a polarization twist tag with two DRs tilted by ±45° and spaced by $\lambda $ /4. In the EM simulation and experiment, we show that this tag design allows efficient retrodirective scattering in cross polarization. The realized cross-polarization radar cross section (RCS) is equal to the scattering of a single DR in LP and 6 dB better than the RCS from a polarization splitting single DR with 45° tilt. This polarization signature is shown to allow separation of the DR signature from the high scattering level of a flat plate reflector placed behind the polarization twist DR tag. The potential of improving lens-DR combinations by using the polarization twist DR tag with circular polarization is also discussed.
- 6 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (12) , 5291-5299
Retrodirective Dielectric Resonator Tag With Polarization Twist Signature for Clutter Suppression in Self-Localization System
In a recently proposed indoor self-localization system, we excite dielectric resonators (DRs) in linear polarization (LP) as retrodirective passive tags, either as single DR, small array of DRs, or in combination with a spherical dielectric lens. DR tags mounted close to a reflecting wall suffer from large clutter return, which can supercede the DR tag signatures. To separate both into orthogonal polarizations, we design a polarization twist tag with two DRs tilted by ±45° and spaced by $\lambda $ /4. In the EM simulation and experiment, we show that this tag design allows efficient retrodirective scattering in cross polarization. The realized cross-polarization radar cross section (RCS) is equal to the scattering of a single DR in LP and 6 dB better than the RCS from a polarization splitting single DR with 45° tilt. This polarization signature is shown to allow separation of the DR signature from the high scattering level of a flat plate reflector placed behind the polarization twist DR tag. The potential of improving lens-DR combinations by using the polarization twist DR tag with circular polarization is also discussed.
- Open Access
- 7 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 218729-218738
OAM Mode Order Conversion and Clutter Rejection With OAM-Coded RFID Tags
In this article, a uniform helically arranged dielectric resonator array can generate Orbital Angular Momentum waves (OAM) causing a conversion of OAM mode orders $m$ from an incoming mode ${m}_{in}$ to an outgoing mode ${m}_{out}$ . The operating frequency is set as 10 GHz to facilitate the measuring process. This new approach provides additional OAM values per digit in the RFID technology according to the excited OAM modes ${m}_{n}\,\,\in \,\,\{\ldots,-2,-1,0,1,2,\ldots \}$ instead of the conventional binary values ${b}_{n}~\in ~\{0, 1\}$ . Thus, more information content is revealed. Through the OAM concept, a ${m}_{1} {m}_{2}~2$ -digits OAM coded tag is obtained upon the employment of two uniform helically arranged cylindrical dielectric resonator arrays operating at two different frequencies ${f}_{1} = 10\,\,\text {GHz}$ , and ${f}_{2} = 11\,\,\text {GHz}$ . Each array has 8 DRs but with different radius yielding a reduction of the mutual coupling between the varied circular arrays. The interaction between the phase delayed radiation of each DR element in the array generates different vortex waves with corresponding OAM mode orders. In order to achieve the correct phase delay, the elevation of each DR is specified by the desirable OAM mode order, the number of elements and the propagation wavelength. At first, the generation of OAM mode orders −1, 2, and −3 is carried out. Then, mode conversion from 0 to −1, +1 to −2, −1 to 0, +2 to −3, and −2 to +1 are depicted. After that, two simulated examples of 2-digits OAM coded tags with the code $\{-1,1\}$ and $\{-2,0\}$ are presented. A conversion of mode 0 to mode 1 has been simulated and also measured, where an additional metal sheet is used to evaluate the distortion in the OAM modes. As a result, this study demonstrates that the uniform helically arranged DR arrays can convert the incoming OAM mode order into another one, where the clutter from broadside direction is rejected due to the Butler matrix (BM), which interferes the clutter destructively.
- 7 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 218729-218738
Open AccessOAM Mode Order Conversion and Clutter Rejection With OAM-Coded RFID Tags
In this article, a uniform helically arranged dielectric resonator array can generate Orbital Angular Momentum waves (OAM) causing a conversion of OAM mode orders $m$ from an incoming mode ${m}_{in}$ to an outgoing mode ${m}_{out}$ . The operating frequency is set as 10 GHz to facilitate the measuring process. This new approach provides additional OAM values per digit in the RFID technology according to the excited OAM modes ${m}_{n}\,\,\in \,\,\{\ldots,-2,-1,0,1,2,\ldots \}$ instead of the conventional binary values ${b}_{n}~\in ~\{0, 1\}$ . Thus, more information content is revealed. Through the OAM concept, a ${m}_{1} {m}_{2}~2$ -digits OAM coded tag is obtained upon the employment of two uniform helically arranged cylindrical dielectric resonator arrays operating at two different frequencies ${f}_{1} = 10\,\,\text {GHz}$ , and ${f}_{2} = 11\,\,\text {GHz}$ . Each array has 8 DRs but with different radius yielding a reduction of the mutual coupling between the varied circular arrays. The interaction between the phase delayed radiation of each DR element in the array generates different vortex waves with corresponding OAM mode orders. In order to achieve the correct phase delay, the elevation of each DR is specified by the desirable OAM mode order, the number of elements and the propagation wavelength. At first, the generation of OAM mode orders −1, 2, and −3 is carried out. Then, mode conversion from 0 to −1, +1 to −2, −1 to 0, +2 to −3, and −2 to +1 are depicted. After that, two simulated examples of 2-digits OAM coded tags with the code $\{-1,1\}$ and $\{-2,0\}$ are presented. A conversion of mode 0 to mode 1 has been simulated and also measured, where an additional metal sheet is used to evaluate the distortion in the OAM modes. As a result, this study demonstrates that the uniform helically arranged DR arrays can convert the incoming OAM mode order into another one, where the clutter from broadside direction is rejected due to the Butler matrix (BM), which interferes the clutter destructively.
- Open Access
Indoor Large-Scale MIMO-Based RSSI Localization with Low-Complexity RFID Infrastructure
Indoor localization based on unsynchronized, low-complexity, passive radio frequency identification (RFID) using the received signal strength indicator (RSSI) has a wide potential for a variety of internet of things (IoTs) applications due to their energy-harvesting capabilities and low complexity. However, conventional RSSI-based algorithms present inaccurate ranging, especially in indoor environments, mainly because of the multipath randomness effect. In this work, we propose RSSI-based localization with low-complexity, passive RFID infrastructure utilizing the potential benefits of large-scale MIMO technology operated in the millimeter-wave band, which offers channel hardening, in order to alleviate the effect of small-scale fading. Particularly, by investigating an indoor environment equipped with extremely simple dielectric resonator (DR) tags, we propose an efficient localization algorithm that enables a smart object equipped with large-scale MIMO exploiting the RSSI measurements obtained from the reference DR tags in order to improve the localization accuracy. In this context, we also derive Cramer–Rao lower bound of the proposed technique. Numerical results evidence the effectiveness of the proposed algorithms considering various arbitrary network topologies, and results are compared with an existing algorithm, where the proposed algorithms not only produce higher localization accuracy but also achieve a greater robustness against inaccuracies in channel modeling.
Open AccessIndoor Large-Scale MIMO-Based RSSI Localization with Low-Complexity RFID Infrastructure
Indoor localization based on unsynchronized, low-complexity, passive radio frequency identification (RFID) using the received signal strength indicator (RSSI) has a wide potential for a variety of internet of things (IoTs) applications due to their energy-harvesting capabilities and low complexity. However, conventional RSSI-based algorithms present inaccurate ranging, especially in indoor environments, mainly because of the multipath randomness effect. In this work, we propose RSSI-based localization with low-complexity, passive RFID infrastructure utilizing the potential benefits of large-scale MIMO technology operated in the millimeter-wave band, which offers channel hardening, in order to alleviate the effect of small-scale fading. Particularly, by investigating an indoor environment equipped with extremely simple dielectric resonator (DR) tags, we propose an efficient localization algorithm that enables a smart object equipped with large-scale MIMO exploiting the RSSI measurements obtained from the reference DR tags in order to improve the localization accuracy. In this context, we also derive Cramer–Rao lower bound of the proposed technique. Numerical results evidence the effectiveness of the proposed algorithms considering various arbitrary network topologies, and results are compared with an existing algorithm, where the proposed algorithms not only produce higher localization accuracy but also achieve a greater robustness against inaccuracies in channel modeling.
- 27 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 69 (7) , 7751-7761
Chipless RFID Infrastructure Based Self-Localization: Testbed Evaluation
This paper presents a realistic feasibility of radio frequency identification (RFID) based self-localization of objects in real environments using simple infrastructure composed of chipless tags. These tags are designed as arrays of dielectric resonators (DR) in order to overcome the range limitations of the traditional chipless tags, where the DR array structure of the tags boosts the radar cross section (RCS) and, consequentially, extends the range coverage. Furthermore, an efficient algorithm for tag detection is proposed considering the environmental and hardware impairments that alter the backscattered signal from the tag. In this system, the reader interrogates the reference nodes, i.e. chipless tags, by a frequency-sweep RF signal, and the backscattered signals from the tags are captured and analyzed at the reader for detection, ranging and location estimation. A testbed is implemented with fabricated chipless RFID tags in order to evaluate the validity and accuracy of the proposed self-localization system. Experimental measurements based simulations are conducted in several scenarios in order to evaluate the proposed system. Moreover, an object (the reader) is moved to several locations in an interrogation area of 2.5*1.2 m, and, afterwards, its location is estimated. The averaged measured location error achieved based on the proposed system is approximately 5 cm with a variation of 0.9 cm as a minimum observed error and 7 cm as a maximum error.
- 27 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 69 (7) , 7751-7761
Chipless RFID Infrastructure Based Self-Localization: Testbed Evaluation
This paper presents a realistic feasibility of radio frequency identification (RFID) based self-localization of objects in real environments using simple infrastructure composed of chipless tags. These tags are designed as arrays of dielectric resonators (DR) in order to overcome the range limitations of the traditional chipless tags, where the DR array structure of the tags boosts the radar cross section (RCS) and, consequentially, extends the range coverage. Furthermore, an efficient algorithm for tag detection is proposed considering the environmental and hardware impairments that alter the backscattered signal from the tag. In this system, the reader interrogates the reference nodes, i.e. chipless tags, by a frequency-sweep RF signal, and the backscattered signals from the tags are captured and analyzed at the reader for detection, ranging and location estimation. A testbed is implemented with fabricated chipless RFID tags in order to evaluate the validity and accuracy of the proposed self-localization system. Experimental measurements based simulations are conducted in several scenarios in order to evaluate the proposed system. Moreover, an object (the reader) is moved to several locations in an interrogation area of 2.5*1.2 m, and, afterwards, its location is estimated. The averaged measured location error achieved based on the proposed system is approximately 5 cm with a variation of 0.9 cm as a minimum observed error and 7 cm as a maximum error.
- Open Access
- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (5) , 726-730
Frequency Selective Surface Coded Retroreflectors for Chipless Indoor Localization Tag Landmarks
This paper presents the integration of frequency selective surfaces (FSSs) with retroreflectors for the realization of chipless wireless indoor localization tag landmarks. As an example, the high radar cross-section (RCS) of a trihedral corner reflector is signed with an FSS-based stop-band filter, so that the backscattered power from several corner reflectors can be distinguished by a mobile reader according to the frequency response of the FSS. Measurement results with a ${3\times3\times3 cm^{3}}$ trihedral corner reflector and a stop-band FSS in a Rogers RT/Duroid® 5880 high-frequency laminate at 90 GHz shows an RCS above -25 dBsqm for 90 degrees coverage in the TM plane. Due to the high RCS, measurements at distances up to 4 meters with a standard 25 dBi gain horn antenna and a vector network analyzer as a reader are shown. These preliminary results show the potential of the concept for applications such as indoor localization with sub-mm accuracy, where high-bandwidths, but only a low number of bits, are needed for the identification of the tag landmarks.- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (5) , 726-730
Open AccessFrequency Selective Surface Coded Retroreflectors for Chipless Indoor Localization Tag Landmarks
This paper presents the integration of frequency selective surfaces (FSSs) with retroreflectors for the realization of chipless wireless indoor localization tag landmarks. As an example, the high radar cross-section (RCS) of a trihedral corner reflector is signed with an FSS-based stop-band filter, so that the backscattered power from several corner reflectors can be distinguished by a mobile reader according to the frequency response of the FSS. Measurement results with a ${3\times3\times3 cm^{3}}$ trihedral corner reflector and a stop-band FSS in a Rogers RT/Duroid® 5880 high-frequency laminate at 90 GHz shows an RCS above -25 dBsqm for 90 degrees coverage in the TM plane. Due to the high RCS, measurements at distances up to 4 meters with a standard 25 dBi gain horn antenna and a vector network analyzer as a reader are shown. These preliminary results show the potential of the concept for applications such as indoor localization with sub-mm accuracy, where high-bandwidths, but only a low number of bits, are needed for the identification of the tag landmarks. - 30 October 2019
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 74 (1-2) , 1-8
Wide-Angle RCS Enhanced Tag Based on Dielectric Resonator – Lens Combination
In a novel mm-wave localization system, dielectric resonators (DR) have been proposed as passive chipless RFID tags to mark fixed reference nodes. To counter clutter and improve the limited read range due to the low RCS level of a DR at millimeter-wave frequencies we propose a combination of several DRs with a dielectric spherical lens which allows improvement of up to 30 dB. The paper presents the design principle and shows simulation results and experimental verification of a scaled tag operating in the 10–12 GHz range and covering a range of incidence angle of the reader signal of ± 50°. A frequency sweeping RF reader can identify the tag (information) by the peak of the RCS level at its DR resonant frequency. For a multiple-tag scenario we can realize up to 12 different tags which can be discriminated unambiguously by their resonant frequencies in a 1: 1.2 frequency bandwidth.
- 30 October 2019
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 74 (1-2) , 1-8
Wide-Angle RCS Enhanced Tag Based on Dielectric Resonator – Lens Combination
In a novel mm-wave localization system, dielectric resonators (DR) have been proposed as passive chipless RFID tags to mark fixed reference nodes. To counter clutter and improve the limited read range due to the low RCS level of a DR at millimeter-wave frequencies we propose a combination of several DRs with a dielectric spherical lens which allows improvement of up to 30 dB. The paper presents the design principle and shows simulation results and experimental verification of a scaled tag operating in the 10–12 GHz range and covering a range of incidence angle of the reader signal of ± 50°. A frequency sweeping RF reader can identify the tag (information) by the peak of the RCS level at its DR resonant frequency. For a multiple-tag scenario we can realize up to 12 different tags which can be discriminated unambiguously by their resonant frequencies in a 1: 1.2 frequency bandwidth.