Weidong Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Weidong Huang has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Xin Lin
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi′an, People’s Republic Of China
8 shared publications - Xufei Lu
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
2 shared publications - Aitang Xue
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an, Shaanxi, People’s Republic of China
1 shared publication - An-Hui Cai
College of Mechanical Engineering, Hunan Institute of Science and Technology, Yueyang 414000, China
1 shared publication - Chen
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an, P.R. China
1 shared publication Chunhui Zhan
Sichuan Aerospace Chuannan Initiating Explosive Technology Limited, Luzhou, People’s Republic of China
1 shared publication
Latest Publications
- 5 March 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 870, 144874
Microstructure and strengthening mechanisms of Zr-modified Al–Cu–Mg alloy processed by selective laser melting
- 5 March 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 870, 144874
Microstructure and strengthening mechanisms of Zr-modified Al–Cu–Mg alloy processed by selective laser melting
- Open Access
- 20 September 2022
- Published by Taylor & Francis in Materials Research Letters
- Vol. 11 (1) , 60-68
Achieving fully-equiaxed fine β-grains in titanium alloy produced by additive manufacturing
The achievement of fine equiaxed β grain with conventional intragranular (α-Ti+β-Ti) microstructure in additive manufacturing titanium alloy remains a big challenge. We conquer this challenge by synergistically controlling β-grains during both solidification and subsequent thermal-cycles of laser directed energy deposition (DED), and a solution + quenching heat-treatment. Both the strength and plasticity of heat-treated Ti6Al4V3Ni0.05B are superior to those reported new DED titanium alloy and comparable to that of DED Ti6Al4V, because of the fine-equiaxed β-grains with intragranular (α-Ti+β-Ti) microstructure. These findings provide new insight into the grain structure control and the composition design of AM titanium alloy. GRAPHICAL ABSTRACT IMPACT STATEMENT The synergetic control of β-grain during both solidification and subsequent thermal-cycling is essential for achieving fully-equiaxed fine β-grains in additively manufactured titanium alloys.
- 20 September 2022
- Published by Taylor & Francis in Materials Research Letters
- Vol. 11 (1) , 60-68
Open AccessAchieving fully-equiaxed fine β-grains in titanium alloy produced by additive manufacturing
The achievement of fine equiaxed β grain with conventional intragranular (α-Ti+β-Ti) microstructure in additive manufacturing titanium alloy remains a big challenge. We conquer this challenge by synergistically controlling β-grains during both solidification and subsequent thermal-cycles of laser directed energy deposition (DED), and a solution + quenching heat-treatment. Both the strength and plasticity of heat-treated Ti6Al4V3Ni0.05B are superior to those reported new DED titanium alloy and comparable to that of DED Ti6Al4V, because of the fine-equiaxed β-grains with intragranular (α-Ti+β-Ti) microstructure. These findings provide new insight into the grain structure control and the composition design of AM titanium alloy. GRAPHICAL ABSTRACT IMPACT STATEMENT The synergetic control of β-grain during both solidification and subsequent thermal-cycling is essential for achieving fully-equiaxed fine β-grains in additively manufactured titanium alloys.
- Open Access
- 29 June 2022
- Published by Taylor & Francis in Materials Research Letters
- Vol. 10 (11) , 720-727
Improved fatigue properties of laser powder bed fusion of Al–4.74Mg–0.70Sc–0.32Zr alloy via hot isostatic pressing
Laser powder bed fusion (L-PBF) processed components usually exhibit reduced fatigue performance owing to unavoidable defects at multiple scales, especially when the loading direction is parallel to the building direction. In this study, hot isostatic pressing (HIP) was applied to the L-PBFed Al-4.74Mg-0.70Sc-0.32Zr (wt.%) alloy to enhance the fatigue properties with a focus on the defect (porosities and inclusions) effects, compared with the direct-aged samples. The results demonstrated that HIP induced inconspicuous microstructural effects, but it healed the porosities and promoted oxidation. Therefore, the fatigue crack initiation transformed the oxide-associated porosity into an oxide, with a significant fatigue strength improvement. GRAPHICAL ABSTRACT IMPACT STATEMENT This study highlights the critical importance of oxides in fatigue performance.
- 29 June 2022
- Published by Taylor & Francis in Materials Research Letters
- Vol. 10 (11) , 720-727
Open AccessImproved fatigue properties of laser powder bed fusion of Al–4.74Mg–0.70Sc–0.32Zr alloy via hot isostatic pressing
Laser powder bed fusion (L-PBF) processed components usually exhibit reduced fatigue performance owing to unavoidable defects at multiple scales, especially when the loading direction is parallel to the building direction. In this study, hot isostatic pressing (HIP) was applied to the L-PBFed Al-4.74Mg-0.70Sc-0.32Zr (wt.%) alloy to enhance the fatigue properties with a focus on the defect (porosities and inclusions) effects, compared with the direct-aged samples. The results demonstrated that HIP induced inconspicuous microstructural effects, but it healed the porosities and promoted oxidation. Therefore, the fatigue crack initiation transformed the oxide-associated porosity into an oxide, with a significant fatigue strength improvement. GRAPHICAL ABSTRACT IMPACT STATEMENT This study highlights the critical importance of oxides in fatigue performance.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
High-Temperature Mechanical Performance of Laser Additive Manufactured Ti6242s Alloy
Ti6242S is a near-α titanium alloy that is expected to be used in engineering below 500°C. In this paper, its high-temperature mechanical performance including the high-temperature tensile property and the high-temperature high-cycle fatigue property is well investigated by laser additive manufacturing (LAM) technology. It is confirmed that the high-temperature tensile mechanical property can highly satisfy the forging standard for heat treated LAM Ti6242S. And the heat-treated LAM Ti6242S is of stable and reliable high-temperature high-cycle fatigue limit relying on an analysis on the coefficient of variation of the fatigue life. It is presented that the high-temperature high-cycle fatigue life of LAM Ti6242S alloy is highly related to the pore position and its size. Thus a new parameter is proposed to build a relationship with the high-temperature high-cycle fatigue life. Moreover, the fatigue deformation mechanism depends strongly on the α and α′ colony orientations that vary frequently and intricately in accordance with the fine microstructure morphology, leading to a reduced crack expansion rate for LAM Ti6242S.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessHigh-Temperature Mechanical Performance of Laser Additive Manufactured Ti6242s Alloy
Ti6242S is a near-α titanium alloy that is expected to be used in engineering below 500°C. In this paper, its high-temperature mechanical performance including the high-temperature tensile property and the high-temperature high-cycle fatigue property is well investigated by laser additive manufacturing (LAM) technology. It is confirmed that the high-temperature tensile mechanical property can highly satisfy the forging standard for heat treated LAM Ti6242S. And the heat-treated LAM Ti6242S is of stable and reliable high-temperature high-cycle fatigue limit relying on an analysis on the coefficient of variation of the fatigue life. It is presented that the high-temperature high-cycle fatigue life of LAM Ti6242S alloy is highly related to the pore position and its size. Thus a new parameter is proposed to build a relationship with the high-temperature high-cycle fatigue life. Moreover, the fatigue deformation mechanism depends strongly on the α and α′ colony orientations that vary frequently and intricately in accordance with the fine microstructure morphology, leading to a reduced crack expansion rate for LAM Ti6242S.
- 4 July 2021
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 16 (4) , 387-403
Simulation-assisted investigation on the formation of layer bands and the microstructural evolution in directed energy deposition of Ti6Al4V blocks
Additive manufacturing (AM) of titanium alloy entails severe microstructural heterogeneity and layer bands due to diverse thermal histories. While the thermal-microstructure relationship in AM has been reported, the details on how complex thermal histories influence the microstructural evolution have not been so addressed, and the formation of layer bands in multi-layer multi-pass builds is still unclear. To undertake such investigation, a thermal model is firstly calibrated using two part-scale blocks fabricated on differently sized substrates, and then used to study the relationship between key microstructural characteristics and the thermal cycling involved. Results show that the different evolutions of the temperature ranges just underneath the β-transus temperature (Tβ) controlled by the printing path are responsible for the different band distributions at the centre and corner of the blocks. Also, the α sizes in the normal region are closely linked to the integral area obtained from the thermal curve as temperature fluctuates between Tβ and α dissolution temperature, which helps linking AM variables to metallurgy. This further demonstrates that the α coarsening during thermal cycles is primarily driven by multi dissolution and precipation transformations instead of Ostwald ripening. Finally, the quantitative thermal-microstructure-microhardness relationship is established, helpful for the microstructural design.
- 4 July 2021
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 16 (4) , 387-403
Simulation-assisted investigation on the formation of layer bands and the microstructural evolution in directed energy deposition of Ti6Al4V blocks
Additive manufacturing (AM) of titanium alloy entails severe microstructural heterogeneity and layer bands due to diverse thermal histories. While the thermal-microstructure relationship in AM has been reported, the details on how complex thermal histories influence the microstructural evolution have not been so addressed, and the formation of layer bands in multi-layer multi-pass builds is still unclear. To undertake such investigation, a thermal model is firstly calibrated using two part-scale blocks fabricated on differently sized substrates, and then used to study the relationship between key microstructural characteristics and the thermal cycling involved. Results show that the different evolutions of the temperature ranges just underneath the β-transus temperature (Tβ) controlled by the printing path are responsible for the different band distributions at the centre and corner of the blocks. Also, the α sizes in the normal region are closely linked to the integral area obtained from the thermal curve as temperature fluctuates between Tβ and α dissolution temperature, which helps linking AM variables to metallurgy. This further demonstrates that the α coarsening during thermal cycles is primarily driven by multi dissolution and precipation transformations instead of Ostwald ripening. Finally, the quantitative thermal-microstructure-microhardness relationship is established, helpful for the microstructural design.
- Open Access
- 1 January 2021
- Published by Elsevier in SSRN Electronic Journal
Ultra Strong and Ductile Eutectic High Entropy Alloy Fabricated by Selective Laser Melting
With important application prospects, eutectic high entropy alloys have received extensive attention for their excellent strength and ductility in a large temperature range. The excellent casting characteristics of eutectic high entropy alloys make it possible to achieve well manufacturability of selective laser melting. For the first time, we have achieved crack-free eutectic high entropy alloy fabricated by selective laser melting, which has excellent mechanical properties in a wide temperature range of -196°C ~ 760°C due to ultra-fine eutectic lamellar spacing of 150 ~ 200nm and lamellar colony of 2 ~ 6μm. Specifically, the room temperature tensile strength exceeds 1400MPa and the elongation is more than 20%, significantly improved compared with those manufactured by other techniques with lower cooling rate.
- 1 January 2021
- Published by Elsevier in SSRN Electronic Journal
Open AccessUltra Strong and Ductile Eutectic High Entropy Alloy Fabricated by Selective Laser Melting
With important application prospects, eutectic high entropy alloys have received extensive attention for their excellent strength and ductility in a large temperature range. The excellent casting characteristics of eutectic high entropy alloys make it possible to achieve well manufacturability of selective laser melting. For the first time, we have achieved crack-free eutectic high entropy alloy fabricated by selective laser melting, which has excellent mechanical properties in a wide temperature range of -196°C ~ 760°C due to ultra-fine eutectic lamellar spacing of 150 ~ 200nm and lamellar colony of 2 ~ 6μm. Specifically, the room temperature tensile strength exceeds 1400MPa and the elongation is more than 20%, significantly improved compared with those manufactured by other techniques with lower cooling rate.
- Open Access
- 28 September 2020
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 15 (sup1) , 570-582
Effect of melting modes on microstructure and tribological properties of selective laser melted AlSi10Mg alloy
This paper focuses on the effect of melting modes on microstructural evolution and tribological properties of AlSi10Mg alloy fabricated by selective laser melting (SLM). The results showed that the microstructures of SLM AlSi10Mg consisted of primary α-Al surrounded by cellular Si networks (∼500 nm) when fabricated in conduction mode, but has a finer cellular-like Si phase (∼200 nm) when fabricated in keyhole mode. The strong convection caused by the melt reflow and Marangoni convection under keyhole mode also resulted in deposition of nano-scale Si particles at the bottom of the molten pool. The SLM AlSi10Mg fabricated in keyhole mode exhibited better wear resistance than that fabricated in conduction mode. Compared to traditional as-cast specimens, both SLM specimens showed better wear resistance due to the unique cellular-like networks. The SLM technique offers a new approach for material processing that can be used to refine microstructures for improved tribological properties.
- 28 September 2020
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 15 (sup1) , 570-582
Open AccessEffect of melting modes on microstructure and tribological properties of selective laser melted AlSi10Mg alloy
This paper focuses on the effect of melting modes on microstructural evolution and tribological properties of AlSi10Mg alloy fabricated by selective laser melting (SLM). The results showed that the microstructures of SLM AlSi10Mg consisted of primary α-Al surrounded by cellular Si networks (∼500 nm) when fabricated in conduction mode, but has a finer cellular-like Si phase (∼200 nm) when fabricated in keyhole mode. The strong convection caused by the melt reflow and Marangoni convection under keyhole mode also resulted in deposition of nano-scale Si particles at the bottom of the molten pool. The SLM AlSi10Mg fabricated in keyhole mode exhibited better wear resistance than that fabricated in conduction mode. Compared to traditional as-cast specimens, both SLM specimens showed better wear resistance due to the unique cellular-like networks. The SLM technique offers a new approach for material processing that can be used to refine microstructures for improved tribological properties.
- 19 March 2019
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 24 (5) , 457-464
Microstructure and mechanical properties of laser solid formed 30Cr–Mn–Si–Ni–2A ultra-high-strength steel
Microstructure and mechanical properties of laser solid formed 30Cr–Mn–Si–Ni–2A steel are investigated. The deposits consist of epitaxial columnar grains, equiaxed grains or direction changed dendrites can be observed in the bulk specimens. The microstructure at the bottom of deposits is mainly composed of tempered martensite; the middle to top zone of the deposits are characterised by martensite and bainite. With the increasing of deposition height, the volume fraction of bainite increases, the size of martensite laths increases but its volume fraction decreases. The microhardness shows a decrease from the bottom zone to the middle–upper zone, and then a significant increase at the top of the deposits. Anisotropic and unevenly distributed tensile properties are observed for the deposits. Samples after heat treatment demonstrate tensile strength of 1720 MPa and elongation rate of 8.7%.
- 19 March 2019
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 24 (5) , 457-464
Microstructure and mechanical properties of laser solid formed 30Cr–Mn–Si–Ni–2A ultra-high-strength steel
Microstructure and mechanical properties of laser solid formed 30Cr–Mn–Si–Ni–2A steel are investigated. The deposits consist of epitaxial columnar grains, equiaxed grains or direction changed dendrites can be observed in the bulk specimens. The microstructure at the bottom of deposits is mainly composed of tempered martensite; the middle to top zone of the deposits are characterised by martensite and bainite. With the increasing of deposition height, the volume fraction of bainite increases, the size of martensite laths increases but its volume fraction decreases. The microhardness shows a decrease from the bottom zone to the middle–upper zone, and then a significant increase at the top of the deposits. Anisotropic and unevenly distributed tensile properties are observed for the deposits. Samples after heat treatment demonstrate tensile strength of 1720 MPa and elongation rate of 8.7%.
- 1 April 2013
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 23 (4) , 1046-1051
Fractal dimension for porous metal materials of FeCrAl fiber
- 1 April 2013
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 23 (4) , 1046-1051
Fractal dimension for porous metal materials of FeCrAl fiber
- 29 September 2010
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 20, s821-s825
In-situ observation of crystal detachment behavior in NH4Cl-H2O system from chilling metal surface with vibration
- 29 September 2010
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 20, s821-s825
In-situ observation of crystal detachment behavior in NH4Cl-H2O system from chilling metal surface with vibration