Thangavel Sangeetha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thangavel Sangeetha has a total of 127 co-authors. Here are the top co-authors by number of shared publications:
- Po-Tuan Chen
Department of Vehicle Engineering, National Taipei University of Technology, Taipei, Taiwan
7 shared publications - Wei-Mon Yan
Department of Energy and Refrigerating Air-Conditioning Engineering, National Taipei University of Technology, Taipei 10608, Taiwan
7 shared publications Wei-Mon Yan
6 shared publications- Cheng-Jung Yang
Department of Mechanical and Electromechanical Engineering National Sun Yat‐Sen University Kaohsiung Taiwan
4 shared publications - Jakub Čespiva
VSB - Technical University of Ostrava
4 shared publications Aijie Wang
State Key Laboratory of Urban Water Resource and Environment, School of Civil and Environmental Engineering, Harbin Institute of Technology Shenzhen, Shenzhen, 518055, China
3 shared publications
Latest Publications
- Open Access
- 15 July 2025
- Published by Elsevier in Energy Reports
- Vol. 14, 944-951
Evaluation of the environmental burden of Co/CoMnK catalytic synthesis wastewater employing acute toxicity tests as a methodological framework
- 15 July 2025
- Published by Elsevier in Energy Reports
- Vol. 14, 944-951
Open AccessEvaluation of the environmental burden of Co/CoMnK catalytic synthesis wastewater employing acute toxicity tests as a methodological framework
- 7 July 2025
- Published by Elsevier in Environmental Research
- Vol. 285 (Pt 1) , 122311
Synergistic effects of magnetic fields and magnetite on anaerobic digestion: Enhancing methane production and microbial activity
- 7 July 2025
- Published by Elsevier in Environmental Research
- Vol. 285 (Pt 1) , 122311
Synergistic effects of magnetic fields and magnetite on anaerobic digestion: Enhancing methane production and microbial activity
- Open Access
Effect of Pretreatments on the Distribution and Removal of Triclosan in Waste-Activated Sludge
Triclosan (TCS) is extensively detected in wastewater and waste-activated sludge (WAS). The occurrence and fate of TCS in anaerobic digestion have been well revealed, but the change in TCS during WAS pretreatment needs to be clarified. Thermal hydrolysis pretreatment has been proven to be efficient for both WAS hydrolysis and TCS removal, with a removal efficiency of 54.0% and a retention time of 90 min at 170 °C. Alkaline pretreatment remarkably changed the TCS distribution between the sludge and liquid, and the solid–liquid distribution coefficient decreased by three orders of magnitude as the pH increased to 13. Neither alkaline pretreatment nor thermal–alkaline pretreatment resulted in the obvious removal of TCS. UP demonstrated limited efficiency in the hydrolysis of WAS, as well as the migration and removal of TCS. Thus, this study demonstrated that pretreatment methods and operational parameters significantly influence the migration and removal of TCS. It also provides a valuable reference for future studies on the migration and degradation behavior of TCS during anaerobic digestion and lays a foundation for the development of WAS treatment engineering capable of efficiently removing TCS.
Open AccessEffect of Pretreatments on the Distribution and Removal of Triclosan in Waste-Activated Sludge
Triclosan (TCS) is extensively detected in wastewater and waste-activated sludge (WAS). The occurrence and fate of TCS in anaerobic digestion have been well revealed, but the change in TCS during WAS pretreatment needs to be clarified. Thermal hydrolysis pretreatment has been proven to be efficient for both WAS hydrolysis and TCS removal, with a removal efficiency of 54.0% and a retention time of 90 min at 170 °C. Alkaline pretreatment remarkably changed the TCS distribution between the sludge and liquid, and the solid–liquid distribution coefficient decreased by three orders of magnitude as the pH increased to 13. Neither alkaline pretreatment nor thermal–alkaline pretreatment resulted in the obvious removal of TCS. UP demonstrated limited efficiency in the hydrolysis of WAS, as well as the migration and removal of TCS. Thus, this study demonstrated that pretreatment methods and operational parameters significantly influence the migration and removal of TCS. It also provides a valuable reference for future studies on the migration and degradation behavior of TCS during anaerobic digestion and lays a foundation for the development of WAS treatment engineering capable of efficiently removing TCS.
- Open Access
- 10 January 2025
- Published by OAE Publishing Inc. in Energy Materials
- Vol. 5 (2)
Sustainable off-grid gasification: co-production of electricity, heat, and activated carbon
The process of gasification is well-known; however, to this day, the applications of such facilities, especially off-grid small-scale units for direct electricity and char production, are scarce. In this study, an off-grid fixed bed downdraft gasification unit is studied from the gaseous/solid product character perspective. This unit represents a possible solution for the emerging call for sustainable decentralised energy sources. Softwood chips were utilised in this study, and their conversion into synthetic gas (direct electricity supply) and solid biochar was observed and analysed. The results show promising values of synthetic gas for potential utilisation in different applications outside the direct combustion process, such as microbial syngas fermentation, with a lower heating value equal to 6.31 MJ·m-3. It appears that during the steam activation process of biochar, both high-quality off-gas of more than 70%vol. H2 (excluding N2) and activated carbon of a specific surface area of 565.87 m2·g-1 can be collected. Further investigations have revealed specific degradation of chemical bonds and material morphology changes during steam gasification. The microporous structure and high specific surface area of the material make it an attractive material for further development as an adsorbent in sorption cooling devices. Therefore, the waste generated within the gasification process is minimised, and the potential of the obtained products will be valued in favour of the sustainability of the remote locations.
- 10 January 2025
- Published by OAE Publishing Inc. in Energy Materials
- Vol. 5 (2)
Open AccessSustainable off-grid gasification: co-production of electricity, heat, and activated carbon
The process of gasification is well-known; however, to this day, the applications of such facilities, especially off-grid small-scale units for direct electricity and char production, are scarce. In this study, an off-grid fixed bed downdraft gasification unit is studied from the gaseous/solid product character perspective. This unit represents a possible solution for the emerging call for sustainable decentralised energy sources. Softwood chips were utilised in this study, and their conversion into synthetic gas (direct electricity supply) and solid biochar was observed and analysed. The results show promising values of synthetic gas for potential utilisation in different applications outside the direct combustion process, such as microbial syngas fermentation, with a lower heating value equal to 6.31 MJ·m-3. It appears that during the steam activation process of biochar, both high-quality off-gas of more than 70%vol. H2 (excluding N2) and activated carbon of a specific surface area of 565.87 m2·g-1 can be collected. Further investigations have revealed specific degradation of chemical bonds and material morphology changes during steam gasification. The microporous structure and high specific surface area of the material make it an attractive material for further development as an adsorbent in sorption cooling devices. Therefore, the waste generated within the gasification process is minimised, and the potential of the obtained products will be valued in favour of the sustainability of the remote locations.
- Open Access
An Assessment of the Catalytic and Adsorptive Performances of Cellulose Acetate-Based Composite Membranes for Oil/Water Emulsion Separation
Cellulose acetate (CA) mixed-matrix membranes incorporating polyvinylpyrrolidone (PVP), bentonite (B or Ben), graphene oxide (GO), and titanium dioxide (TiO2) were prepared by the phase inversion separation technique for oil/water separation. An investigation was performed where the mixed-matrix membrane was tested for the separation performance of hydrophilic and hydrophobic surface properties. An ultrafiltration experiment at the laboratory scale was used to test dead-end ultrafiltration models developed for the treatment performances of oily wastewater under dynamic full-scale operating conditions. Artificial oily wastewater solutions were prepared from hexane, toluene, and engine oil with Tween80 emulsions for oil removal treatment using composite membranes. The impacts of material hydrophilicity, weight loss, permeability, and pore size were investigated, and it was found that the oil retention of membranes with larger pore sizes enabled much more sophisticated water flux. The CA-GO-, CA-B-, and CA-TiO2-incorporated membranes achieved pure water flux (PWF) values of 45.19, 53.41, and 100.25 L/m2h, respectively. The performance of CA-TiO2 in oil/water emulsion rejection was assessed, and the rejection of engine oil/water, toluene/water, and hexane/water mixtures was determined to be 95.21%, 90.33%, and 92.4%, respectively. The CA-based mixed-matrix membrane portrayed better antifouling properties due to enhanced hydrophilicity and water molecules. The CA-TiO2-incorporated membrane possessed the potential to provide high separation efficiency for oily wastewater treatment. This study demonstrates the potential of fine-tuning membrane performances through material hybridization to achieve efficient wastewater treatment.
Open AccessAn Assessment of the Catalytic and Adsorptive Performances of Cellulose Acetate-Based Composite Membranes for Oil/Water Emulsion Separation
Cellulose acetate (CA) mixed-matrix membranes incorporating polyvinylpyrrolidone (PVP), bentonite (B or Ben), graphene oxide (GO), and titanium dioxide (TiO2) were prepared by the phase inversion separation technique for oil/water separation. An investigation was performed where the mixed-matrix membrane was tested for the separation performance of hydrophilic and hydrophobic surface properties. An ultrafiltration experiment at the laboratory scale was used to test dead-end ultrafiltration models developed for the treatment performances of oily wastewater under dynamic full-scale operating conditions. Artificial oily wastewater solutions were prepared from hexane, toluene, and engine oil with Tween80 emulsions for oil removal treatment using composite membranes. The impacts of material hydrophilicity, weight loss, permeability, and pore size were investigated, and it was found that the oil retention of membranes with larger pore sizes enabled much more sophisticated water flux. The CA-GO-, CA-B-, and CA-TiO2-incorporated membranes achieved pure water flux (PWF) values of 45.19, 53.41, and 100.25 L/m2h, respectively. The performance of CA-TiO2 in oil/water emulsion rejection was assessed, and the rejection of engine oil/water, toluene/water, and hexane/water mixtures was determined to be 95.21%, 90.33%, and 92.4%, respectively. The CA-based mixed-matrix membrane portrayed better antifouling properties due to enhanced hydrophilicity and water molecules. The CA-TiO2-incorporated membrane possessed the potential to provide high separation efficiency for oily wastewater treatment. This study demonstrates the potential of fine-tuning membrane performances through material hybridization to achieve efficient wastewater treatment.
- 8 July 2024
- Published by Elsevier in Bioresource Technology
- Vol. 407, 131094
Impact and migration behavior of triclosan on waste-activated sludge anaerobic digestion
- 8 July 2024
- Published by Elsevier in Bioresource Technology
- Vol. 407, 131094
Impact and migration behavior of triclosan on waste-activated sludge anaerobic digestion
- Open Access
The Bacharach Method: A Low-Cost Tool for Small-Scale Combustion Units’ Flue Gas Quality Control
Although current EU regulations, such as EU Directive 2015/1189 on the eco-design of solid fuel boilers and Directive 2015/1188, in accordance with the Machinery Directive 2006/42/EC, require manufacturers to meet specific emission requirements for CE marking, the routine and regular onsite testing of household heating appliances is still not mandatory in many EU countries. This research endeavour addressed this gap by evaluating the effectiveness of the Bacharach method as a rapid and cost-effective tool for assessing flue gas quality, particularly in terms of particulate matter mass concentration. This study also compared the results of the Bacharach method with those obtained from two commercially available portable analysers. The research outcomes demonstrate that the Bacharach method, in combination with an innovative evaluation approach, offers a viable solution, enabling the swift and economical assessment of flue gas quality with the primary objective of determining the boiler class according to the limits specified by standard EN 303-5 under operating conditions. The modified Bacharach method for measuring TSP in solid fuel-fired boilers provides qualitatively similar results to the commercially used SM500 and STM225 instruments. The modified Bacharach methodology was primarily developed for comparison to the boiler class 3 limit (i.e., 125 and 150 mg/m3). The study revealed that the modified Bacharach method, when applied to biomass-based boilers, exhibited higher accuracies in the case of classification into classes 3 and 4, whereas fossil fuel-based boilers demonstrated higher accuracy in the case of class 5 limits.
Open AccessThe Bacharach Method: A Low-Cost Tool for Small-Scale Combustion Units’ Flue Gas Quality Control
Although current EU regulations, such as EU Directive 2015/1189 on the eco-design of solid fuel boilers and Directive 2015/1188, in accordance with the Machinery Directive 2006/42/EC, require manufacturers to meet specific emission requirements for CE marking, the routine and regular onsite testing of household heating appliances is still not mandatory in many EU countries. This research endeavour addressed this gap by evaluating the effectiveness of the Bacharach method as a rapid and cost-effective tool for assessing flue gas quality, particularly in terms of particulate matter mass concentration. This study also compared the results of the Bacharach method with those obtained from two commercially available portable analysers. The research outcomes demonstrate that the Bacharach method, in combination with an innovative evaluation approach, offers a viable solution, enabling the swift and economical assessment of flue gas quality with the primary objective of determining the boiler class according to the limits specified by standard EN 303-5 under operating conditions. The modified Bacharach method for measuring TSP in solid fuel-fired boilers provides qualitatively similar results to the commercially used SM500 and STM225 instruments. The modified Bacharach methodology was primarily developed for comparison to the boiler class 3 limit (i.e., 125 and 150 mg/m3). The study revealed that the modified Bacharach method, when applied to biomass-based boilers, exhibited higher accuracies in the case of classification into classes 3 and 4, whereas fossil fuel-based boilers demonstrated higher accuracy in the case of class 5 limits.
- Open Access
Perspective of material evolution Induced by sinusoidal reflex charging in lithium-ion batteries
- Open Access
Co-Gasification of Pistachio Shells with Wood Pellets in a Semi-Industrial Hybrid Cross/Updraft Reactor for Producer Gas and Biochar Production
The possibilities of pistachio shell biochar production on laboratory-scale gasification and pyrolysis devices have been described by several previous studies. Nevertheless, the broader results of the pistachio shell co-gasification process on pilot-scale units have not yet been properly investigated or reported, especially regarding the detailed description of the biochar acquired during the routine operation. The biochar was analysed using several analytical techniques, such as ultimate and proximate analysis (62%wt of C), acid–base properties analysis (pH 9.52), Fourier-transform infrared spectroscopy (the presence of –OH bonds and identification of cellulose, hemicellulose and lignin), Raman spectroscopy (no determination of Id/Ig ratio due to high fluorescence), and nitrogen physisorption (specific surface 50.895 m2·g−1). X-ray fluorescence analysis exhibited the composition of the main compounds in the biochar ash (32.5%wt of Cl and 40.02%wt of Na2O). From the energy generation point of view, the lower heating value of the producer gas achieved 6.53 MJ·m−3 during the co-gasification. The relatively high lower heating value of the producer gas was mainly due to the significant volume fractions of CO (6.5%vol.), CH4 (14.2%vol.), and H2 (4.8 %vol.), while hot gas efficiency accomplished 89.6%.
Open AccessCo-Gasification of Pistachio Shells with Wood Pellets in a Semi-Industrial Hybrid Cross/Updraft Reactor for Producer Gas and Biochar Production
The possibilities of pistachio shell biochar production on laboratory-scale gasification and pyrolysis devices have been described by several previous studies. Nevertheless, the broader results of the pistachio shell co-gasification process on pilot-scale units have not yet been properly investigated or reported, especially regarding the detailed description of the biochar acquired during the routine operation. The biochar was analysed using several analytical techniques, such as ultimate and proximate analysis (62%wt of C), acid–base properties analysis (pH 9.52), Fourier-transform infrared spectroscopy (the presence of –OH bonds and identification of cellulose, hemicellulose and lignin), Raman spectroscopy (no determination of Id/Ig ratio due to high fluorescence), and nitrogen physisorption (specific surface 50.895 m2·g−1). X-ray fluorescence analysis exhibited the composition of the main compounds in the biochar ash (32.5%wt of Cl and 40.02%wt of Na2O). From the energy generation point of view, the lower heating value of the producer gas achieved 6.53 MJ·m−3 during the co-gasification. The relatively high lower heating value of the producer gas was mainly due to the significant volume fractions of CO (6.5%vol.), CH4 (14.2%vol.), and H2 (4.8 %vol.), while hot gas efficiency accomplished 89.6%.