Vyacheslav S. Golovin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vyacheslav S. Golovin has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Sergey Olegovich Slipchenko
Ioffe Institute
12 shared publications Nikita A. Pikhtin
Ioffe Institute, Saint Petersburg, Russia
6 shared publicationsAleksandr A. Podoskin
Ioffe Institute, Saint Petersburg, Russia
5 shared publicationsN A Pikhtin
Ioffe Institute, 26 Polithekhnicheskaya St., 194021 Saint Petersburg, Russia
5 shared publications- Olga S. Soboleva
Ioffe Institute, Saint Petersburg, Russia
5 shared publications S O Slipchenko
Ioffe Institute, 26 Polithekhnicheskaya St., 194021 Saint Petersburg, Russia
5 shared publications
Latest Publications
- 1 April 2022
- Published by IOP Publishing in Quantum Electronics
- Vol. 52 (4) , 343-350
Analysis of light – current characteristics of high-power semiconductor lasers (1060 nm) in a steady-state 2D model
This paper presents a 2D model of a high-power semiconductor laser, which takes into account carrier transport across the layers of its heterostructure and longitudinal spatial hole burning (LSHB), an effect related to the nonuniform gain distribution along the cavity axis. We show that the use of the 2D model which takes into account carrier transport across the layers of the heterostructure allows an appreciable contribution of LSHB to saturation of light – current characteristics to be demonstrated. The LSHB effect, causing a decrease in the output optical power of semiconductor lasers, is shown to be stronger at high drive currents and low output mirror reflectivities. In the case of high drive currents, the LSHB-induced drop in power is related to the faster growth of internal optical and recombination losses because of the nonuniform current density distribution along the cavity axis, such that the highest current density can be almost twice the lowest one. LSHB is shown to increase the power stored in a Fabry – Perot cavity, which is an additional mechanism reducing the output optical power.
- 1 April 2022
- Published by IOP Publishing in Quantum Electronics
- Vol. 52 (4) , 343-350
Analysis of light – current characteristics of high-power semiconductor lasers (1060 nm) in a steady-state 2D model
This paper presents a 2D model of a high-power semiconductor laser, which takes into account carrier transport across the layers of its heterostructure and longitudinal spatial hole burning (LSHB), an effect related to the nonuniform gain distribution along the cavity axis. We show that the use of the 2D model which takes into account carrier transport across the layers of the heterostructure allows an appreciable contribution of LSHB to saturation of light – current characteristics to be demonstrated. The LSHB effect, causing a decrease in the output optical power of semiconductor lasers, is shown to be stronger at high drive currents and low output mirror reflectivities. In the case of high drive currents, the LSHB-induced drop in power is related to the faster growth of internal optical and recombination losses because of the nonuniform current density distribution along the cavity axis, such that the highest current density can be almost twice the lowest one. LSHB is shown to increase the power stored in a Fabry – Perot cavity, which is an additional mechanism reducing the output optical power.
- 16 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (13) , 4321-4325
Systematic Optimization of QW Semiconductor Laser Design for Subnanosecond Pulse Generation by Gain Switching
We have studied the basic principles of quantum well semiconductor laser design optimization and current pumping requirements for generating optical pulses with a defined width and maximum peak power by gain switching. It is shown that for a given pulse width there exist a set of optimal values of optical confinement factor, resonator length and current pulse amplitude, that ensure maximum peak output power. It is determined that the maximum output power is achieved when the optical confinement factor is as low as possible, so that the pulse width does not exceed the target value. The optimal resonator length is found to strongly depend on the target pulse width.
- 16 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (13) , 4321-4325
Systematic Optimization of QW Semiconductor Laser Design for Subnanosecond Pulse Generation by Gain Switching
We have studied the basic principles of quantum well semiconductor laser design optimization and current pumping requirements for generating optical pulses with a defined width and maximum peak power by gain switching. It is shown that for a given pulse width there exist a set of optimal values of optical confinement factor, resonator length and current pulse amplitude, that ensure maximum peak output power. It is determined that the maximum output power is achieved when the optical confinement factor is as low as possible, so that the pulse width does not exceed the target value. The optimal resonator length is found to strongly depend on the target pulse width.
- 22 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (6) , 2855-2860
Low-Voltage Thyristor Heterostructure for High-Current Pulse Generation at High Repetition Rate
The article presents a new design of an AlGaAs/GaAs low-voltage thyristor for efficient high-current pulse generation at high repetition rates. It is demonstrated that optimizing the low-voltage thyristor p-base doping profile by using a thin highly doped layer allows for a significant increase in the operating frequencies. This applies to both a thyristor working without an external load and a vertical stack of a thyristor with a laser diode mini bar (LDMB). It is shown that the use of a 0.1- $\mu \text{m}$ -thick highly doped layer, formed at the side of the p-base close to the n-emitter, leads to a significant increase of the holding current, which in our case exceeds 70 mA. At the same time, we were still able to obtain a low residual voltage of 1.5 V and a high blocking voltage of 32 V. The developed low-voltage thyristors have demonstrated the possibility of generating current pulses of 30-ns duration at a repetition rate of 10/70 kHz with an amplitude of 125/110 A, as well as the efficient pumping of LDMBs and laser pulses with a peak power of 68/57.5 W, respectively.
- 22 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (6) , 2855-2860
Low-Voltage Thyristor Heterostructure for High-Current Pulse Generation at High Repetition Rate
The article presents a new design of an AlGaAs/GaAs low-voltage thyristor for efficient high-current pulse generation at high repetition rates. It is demonstrated that optimizing the low-voltage thyristor p-base doping profile by using a thin highly doped layer allows for a significant increase in the operating frequencies. This applies to both a thyristor working without an external load and a vertical stack of a thyristor with a laser diode mini bar (LDMB). It is shown that the use of a 0.1- $\mu \text{m}$ -thick highly doped layer, formed at the side of the p-base close to the n-emitter, leads to a significant increase of the holding current, which in our case exceeds 70 mA. At the same time, we were still able to obtain a low residual voltage of 1.5 V and a high blocking voltage of 32 V. The developed low-voltage thyristors have demonstrated the possibility of generating current pulses of 30-ns duration at a repetition rate of 10/70 kHz with an amplitude of 125/110 A, as well as the efficient pumping of LDMBs and laser pulses with a peak power of 68/57.5 W, respectively.
- 1 January 2021
- Published by Ioffe Institute Russian Academy of Sciences in Физика и техника полупроводников
- Vol. 55 (5) , 466
Исследование пространственной динамики включения лазера-тиристора (905 нм) на основе многопереходной гетероструктуры AlGaAs/InGaAs/GaAs
The switching on process spatial dynamics of a laser-thyristor based on an AlGaAs/InGaAs/GaAs heterostructure with a thin p-base has been studied. The heterostructure had a modified base with a middle-doped layer at the n-emitter, which makes it possible to increase the operating voltages in order to generate nanosecond current pulses. In laser thyristor pulsed sources based on the proposed heterostructure, a high degree of current flow region localization arising during turn on process of the device was demonstrated. Using the current localization regions luminescence, the propagation dynamics of the switched-on state was estimated. The anode contact sizes required for the nanosecond range pulsed current switches or laser emitters development are obtained.
- 1 January 2021
- Published by Ioffe Institute Russian Academy of Sciences in Физика и техника полупроводников
- Vol. 55 (5) , 466
Исследование пространственной динамики включения лазера-тиристора (905 нм) на основе многопереходной гетероструктуры AlGaAs/InGaAs/GaAs
The switching on process spatial dynamics of a laser-thyristor based on an AlGaAs/InGaAs/GaAs heterostructure with a thin p-base has been studied. The heterostructure had a modified base with a middle-doped layer at the n-emitter, which makes it possible to increase the operating voltages in order to generate nanosecond current pulses. In laser thyristor pulsed sources based on the proposed heterostructure, a high degree of current flow region localization arising during turn on process of the device was demonstrated. Using the current localization regions luminescence, the propagation dynamics of the switched-on state was estimated. The anode contact sizes required for the nanosecond range pulsed current switches or laser emitters development are obtained.
- 24 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (1) , 11-14
High-Power and Repetion Rate Nanosecond Pulse Generation in “Diode Laser—Thyristor” Stacks
The “laser diode mini-bar (LDMB) – multi-element thyristor array (META)” vertical stack design is developed and its optoelectronic characteristics are studied. It is shown that adding a highly-doped layer to a low-voltage thyristor p-base leads to an increase in the repetition rate up to 1 MHz at nanosecond laser and current pulses. Laser pulses with 11.5 W peak power and 2.4 ns pulse width at 1 MHz repetition rate are demonstrated using the META chip, comprised of 4 elements, as a high-current switch. It is shown that the difference between LDMB elements’ turn-on delays does not exceed 400 ps. An increase in the pulse repetition rate from 10 kHz to 1 MHz at the operating voltage of 25 V is accompanied by insignificant LDMB heating (up to 3°C) and a slight decrease in the laser pulse peak power (from 11.5 W to 11.1 W).
- 24 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (1) , 11-14
High-Power and Repetion Rate Nanosecond Pulse Generation in “Diode Laser—Thyristor” Stacks
The “laser diode mini-bar (LDMB) – multi-element thyristor array (META)” vertical stack design is developed and its optoelectronic characteristics are studied. It is shown that adding a highly-doped layer to a low-voltage thyristor p-base leads to an increase in the repetition rate up to 1 MHz at nanosecond laser and current pulses. Laser pulses with 11.5 W peak power and 2.4 ns pulse width at 1 MHz repetition rate are demonstrated using the META chip, comprised of 4 elements, as a high-current switch. It is shown that the difference between LDMB elements’ turn-on delays does not exceed 400 ps. An increase in the pulse repetition rate from 10 kHz to 1 MHz at the operating voltage of 25 V is accompanied by insignificant LDMB heating (up to 3°C) and a slight decrease in the laser pulse peak power (from 11.5 W to 11.1 W).
- 24 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (1) , 7-10
Near-Field Dynamics of Ultra-Wide-Aperture (800 μm) Diode Lasers Under Nanosecond Pulse Excitation
We present a study of near-field dynamics of ultra-wide-aperture (800 μm) high-power diode lasers pumped by nanosecond current pulses. The studied lasers are based on AlGaAs/InGaAs/GaAs asymmetric heterostructure with a wide waveguide and operate at 1060 nm. It is shown that an increased aperture width of 800 μm makes it possible to maintain high emission efficiency at high currents for 3 ns pulses. It is determined that lasing turn-on delay is inhomogeneous along the aperture. Initial turn-on occurs at the edges, while the delay near the aperture center reaches 180–450 ps depending on resonator length and current amplitude. For instance, resonator lengths over 2.5 mm and current amplitude of 90 A correspond to turn-on delay of 200 ps.
- 24 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (1) , 7-10
Near-Field Dynamics of Ultra-Wide-Aperture (800 μm) Diode Lasers Under Nanosecond Pulse Excitation
We present a study of near-field dynamics of ultra-wide-aperture (800 μm) high-power diode lasers pumped by nanosecond current pulses. The studied lasers are based on AlGaAs/InGaAs/GaAs asymmetric heterostructure with a wide waveguide and operate at 1060 nm. It is shown that an increased aperture width of 800 μm makes it possible to maintain high emission efficiency at high currents for 3 ns pulses. It is determined that lasing turn-on delay is inhomogeneous along the aperture. Initial turn-on occurs at the edges, while the delay near the aperture center reaches 180–450 ps depending on resonator length and current amplitude. For instance, resonator lengths over 2.5 mm and current amplitude of 90 A correspond to turn-on delay of 200 ps.
- 1 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (11) , 4977-4982
The Effect of the Carrier Drift Velocity Saturation in High-Power Semiconductor Lasers at Ultrahigh Drive Currents
- 1 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (11) , 4977-4982
The Effect of the Carrier Drift Velocity Saturation in High-Power Semiconductor Lasers at Ultrahigh Drive Currents
- 17 March 2020
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11301, 113011G-50
Energy barrier layers for high-power semiconductor lasers of 1550 nm spectral range (Conference Presentation)
The effect of the number and position of AlInAs energy barrier layers on the output characteristics of high-power multimode AlGaInAs / InP lasers, spectral range 1400–1600 nm, has been studied. It was shown that the use of energy barriers allows increasing the laser maximum output power 1.5-2 times. It was found that the barrier layer should be installed at the waveguide-cladding heterojunction from the p-side in order to localize electrons in the waveguide layer. The study was supported by the Russian Science Foundation, project No. 19-79-30072
- 17 March 2020
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11301, 113011G-50
Energy barrier layers for high-power semiconductor lasers of 1550 nm spectral range (Conference Presentation)
The effect of the number and position of AlInAs energy barrier layers on the output characteristics of high-power multimode AlGaInAs / InP lasers, spectral range 1400–1600 nm, has been studied. It was shown that the use of energy barriers allows increasing the laser maximum output power 1.5-2 times. It was found that the barrier layer should be installed at the waveguide-cladding heterojunction from the p-side in order to localize electrons in the waveguide layer. The study was supported by the Russian Science Foundation, project No. 19-79-30072
- Open Access
- 1 March 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1482 (1)
Numerical investigation of longitudinal spatial hole burning (LSHB) in high-power semiconductor lasers
Longitudinal spatial hole burning (LSHB) and its effect on output power of broad-area semiconductor lasers are examined using one-dimensional rate equations. It is shown that direct LSHB can be separated into two mechanisms – an increase in the effective threshold current and a decrease in the output efficiency. The LSHB dependence on laser diode parameters is analysed. In particular, a large optical confinement factor Γ is shown to suppress the LSHB-induced power decrease.
- 1 March 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1482 (1)
Open AccessNumerical investigation of longitudinal spatial hole burning (LSHB) in high-power semiconductor lasers
Longitudinal spatial hole burning (LSHB) and its effect on output power of broad-area semiconductor lasers are examined using one-dimensional rate equations. It is shown that direct LSHB can be separated into two mechanisms – an increase in the effective threshold current and a decrease in the output efficiency. The LSHB dependence on laser diode parameters is analysed. In particular, a large optical confinement factor Γ is shown to suppress the LSHB-induced power decrease.
- 20 February 2020
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 37 (3) , 784-788
Properties of external-cavity high-power semiconductor lasers based on a single InGaAs quantum well at high pulsed current pump
Properties of light characteristics of external-cavity high-power semiconductor lasers with an active region based on a single InGaAs quantum well operating at ultrahigh pulsed currents are studied. A maximum peak power of 45 W at 110 A (from the aperture of 100 µm), a linewidth of 0.15 nm, and a wavelength in the range of 1040–1070 nm are demonstrated for an external-cavity laser. The tuning range narrows with an increase in the pump current from 27 nm at a current of 20 A to 23 nm at a current of 100 A. The maximum side-mode suppression ratio is up to 45 dB in the central region of the tuning range, while at the edges of this range it was no worse than 20 dB. It is determined that the tuning range of the laser spectrum is limited by the onset of an additional Fabry–Perot cavity line in the spectrum.
- 20 February 2020
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 37 (3) , 784-788
Properties of external-cavity high-power semiconductor lasers based on a single InGaAs quantum well at high pulsed current pump
Properties of light characteristics of external-cavity high-power semiconductor lasers with an active region based on a single InGaAs quantum well operating at ultrahigh pulsed currents are studied. A maximum peak power of 45 W at 110 A (from the aperture of 100 µm), a linewidth of 0.15 nm, and a wavelength in the range of 1040–1070 nm are demonstrated for an external-cavity laser. The tuning range narrows with an increase in the pump current from 27 nm at a current of 20 A to 23 nm at a current of 100 A. The maximum side-mode suppression ratio is up to 45 dB in the central region of the tuning range, while at the edges of this range it was no worse than 20 dB. It is determined that the tuning range of the laser spectrum is limited by the onset of an additional Fabry–Perot cavity line in the spectrum.