George Pichurov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
George Pichurov has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Peter Stankov
Centre for Research and Design in Human Comfort, Energy and Environment (CERDECEN), Technical University of Sofia, 8 Kliment Ochridski Blvd, 1000 Sofia, Bulgaria
8 shared publications - Detelin Markov
Centre for Research and Design in Human Comfort, Energy and Environment (CERDECEN), Technical University of Sofia, 8 Kliment Ohridsky Blvd, 1000 Sofia, Bulgaria
6 shared publications - Iskra Simova
Department of Hydroaerodynamics and Hydraulic Machines, Technical University of Sofia, 1000 Sofia, Bulgaria
6 shared publications - Angel Terziev
Faculty of Power Engineering and Power Machines, Technical University of Sofia, 1756 Sofia, Bulgaria
4 shared publications - Martin Ivanov
Faculty of Power Engineering and Power Machines, Technical University of Sofia, 1756 Sofia, Bulgaria
4 shared publications - Radostina A. Angelova
Department of Hydroaerodynamics and Hydraulic Machines, Technical University of Sofia, Sofia, Bulgaria
4 shared publications
Latest Publications
- Open Access
Modeling the Non-Premixed Combustion of Methane Enriched by Hydrogen in a Cylindrical Combustor
The global shift toward cleaner energy has positioned hydrogen-enriched methane (CH4/H2) as a practical bridge fuel. While it burns more efficiently and produces fewer carbon emissions than traditional hydrocarbons, it introduces operational and safety challenges. Hydrogen’s high reactivity and rapid burning velocity increase risks such as flashback and premature ignition. This study employs Computational Fluid Dynamics to examine the combustion behavior of methane−hydrogen blends in a 2D axisymmetric chamber based on RANS equations. Using ANSYS Fluent 19.1, the research utilizes a validated equilibrium mixture-fraction/PDF framework to ensure accuracy against physical experiments. The simulation framework successfully captures the complexity of non-premixed turbulent combustion by combining a probability density function approach with a realizable k-ε turbulence model. Moreover, this research explores how varying hydrogen concentrations and air mass flow rates, covering the full spectrum from lean to fuel-rich conditions, affect fluid dynamics, turbulence, and the development of recirculation zones. The data show that adding hydrogen fundamentally reshapes velocity fields and thermal profiles, which in turn dictate combustion efficiency and pollutant formation. It has been demonstrated that the optimal blend for combustion performance is the case containing 30% hydrogen. Furthermore, evaluations involving higher-fraction blends (approaching the 70% enrichment range) suggest that configurations exceeding this level necessitate a redesign of the injector near field to mitigate localized heat release and accelerated NOx emissions. By identifying the operational limits for CH4/H2 blends in industrial settings such as steam boilers, this study offers a technical roadmap for engineering more stable, high-performance, and low-carbon energy infrastructure.
Open AccessModeling the Non-Premixed Combustion of Methane Enriched by Hydrogen in a Cylindrical Combustor
The global shift toward cleaner energy has positioned hydrogen-enriched methane (CH4/H2) as a practical bridge fuel. While it burns more efficiently and produces fewer carbon emissions than traditional hydrocarbons, it introduces operational and safety challenges. Hydrogen’s high reactivity and rapid burning velocity increase risks such as flashback and premature ignition. This study employs Computational Fluid Dynamics to examine the combustion behavior of methane−hydrogen blends in a 2D axisymmetric chamber based on RANS equations. Using ANSYS Fluent 19.1, the research utilizes a validated equilibrium mixture-fraction/PDF framework to ensure accuracy against physical experiments. The simulation framework successfully captures the complexity of non-premixed turbulent combustion by combining a probability density function approach with a realizable k-ε turbulence model. Moreover, this research explores how varying hydrogen concentrations and air mass flow rates, covering the full spectrum from lean to fuel-rich conditions, affect fluid dynamics, turbulence, and the development of recirculation zones. The data show that adding hydrogen fundamentally reshapes velocity fields and thermal profiles, which in turn dictate combustion efficiency and pollutant formation. It has been demonstrated that the optimal blend for combustion performance is the case containing 30% hydrogen. Furthermore, evaluations involving higher-fraction blends (approaching the 70% enrichment range) suggest that configurations exceeding this level necessitate a redesign of the injector near field to mitigate localized heat release and accelerated NOx emissions. By identifying the operational limits for CH4/H2 blends in industrial settings such as steam boilers, this study offers a technical roadmap for engineering more stable, high-performance, and low-carbon energy infrastructure.
- Open Access
Hydrogen-Enhanced Combustion of Hydrocarbons
Strong policy momentum is supporting the adoption of hydrogen as a major energy carrier for a decarbonised global economy, especially for reducing emissions in hard-to-abate industrial sectors. Although achieving large-scale hydrogen deployment will require substantial long-term investment in dedicated infrastructure, blending hydrogen with conventional hydrocarbon fuels provides a practical near-term pathway to accelerate uptake by leveraging existing systems and fuel-supply networks. To inform future research and development in this field, this review summarises experimental and numerical findings on the combustion behaviour of hydrogen–hydrocarbon mixtures and highlights the main challenges and research gaps that must be addressed to ensure the safe and efficient use of hydrogen-enriched fuels in current combustion systems. It also examines the fundamental combustion characteristics of hydrogen and hydrogen-enriched fuels, the effects of hydrogen addition to gaseous, liquid, and solid fuels on combustion performance and emissions, and the contrasting policy approaches shaping hydrogen uptake across major global economies.
Open AccessHydrogen-Enhanced Combustion of Hydrocarbons
Strong policy momentum is supporting the adoption of hydrogen as a major energy carrier for a decarbonised global economy, especially for reducing emissions in hard-to-abate industrial sectors. Although achieving large-scale hydrogen deployment will require substantial long-term investment in dedicated infrastructure, blending hydrogen with conventional hydrocarbon fuels provides a practical near-term pathway to accelerate uptake by leveraging existing systems and fuel-supply networks. To inform future research and development in this field, this review summarises experimental and numerical findings on the combustion behaviour of hydrogen–hydrocarbon mixtures and highlights the main challenges and research gaps that must be addressed to ensure the safe and efficient use of hydrogen-enriched fuels in current combustion systems. It also examines the fundamental combustion characteristics of hydrogen and hydrogen-enriched fuels, the effects of hydrogen addition to gaseous, liquid, and solid fuels on combustion performance and emissions, and the contrasting policy approaches shaping hydrogen uptake across major global economies.
- Open Access
A CFD Model for the Evaporation of Sub-Micron Droplet Sprays Across Normal Shocks
The rapid evaporation of liquid droplets across a normal shock wave is a phenomenon of critical importance in advanced propulsion and clean energy systems, such as NH3 supersonic separation. The conventional Spalding d2-law is commonly used to model such phenomena, but it is not suitable for predicting the complete vaporization of sub-micron droplets, particularly as evaporation approaches the free-molecular regime. To address this issue, this paper introduces a novel time-dependent one-dimensional CFD model, which is used to analyze the shock structure, the non-equilibrium heat and mass transfer between the liquid and gas phases, and the evolution of the droplets’ size through the shock. The model describes the evaporation of NH3 sub-micron droplet sprays across a stationary normal shock for various fractions of the liquid phase. The Gyarmathy evaporation model is utilized to accurately account for the transition from diffusion-governed to free-molecular regimes, alongside a new two-phase Rankine–Hugoniot shock jump formulation. The study reveals the influence of a steady normal shock on the physical structure of a droplet-laden flow, including the existence of an initial droplet size swelling through the shock, and quantifies the subsequent complete evaporation of the suspended droplets. The maximum swelling throughout the shock is up to 17%, which corresponds to the case with 8% liquid phase mass fraction in the flow. The model provides acceptable accuracy in calculating the two-phase parameters in high-speed flows and can be extended for modeling more complex, multidimensional detonation and propulsion systems.
Open AccessA CFD Model for the Evaporation of Sub-Micron Droplet Sprays Across Normal Shocks
The rapid evaporation of liquid droplets across a normal shock wave is a phenomenon of critical importance in advanced propulsion and clean energy systems, such as NH3 supersonic separation. The conventional Spalding d2-law is commonly used to model such phenomena, but it is not suitable for predicting the complete vaporization of sub-micron droplets, particularly as evaporation approaches the free-molecular regime. To address this issue, this paper introduces a novel time-dependent one-dimensional CFD model, which is used to analyze the shock structure, the non-equilibrium heat and mass transfer between the liquid and gas phases, and the evolution of the droplets’ size through the shock. The model describes the evaporation of NH3 sub-micron droplet sprays across a stationary normal shock for various fractions of the liquid phase. The Gyarmathy evaporation model is utilized to accurately account for the transition from diffusion-governed to free-molecular regimes, alongside a new two-phase Rankine–Hugoniot shock jump formulation. The study reveals the influence of a steady normal shock on the physical structure of a droplet-laden flow, including the existence of an initial droplet size swelling through the shock, and quantifies the subsequent complete evaporation of the suspended droplets. The maximum swelling throughout the shock is up to 17%, which corresponds to the case with 8% liquid phase mass fraction in the flow. The model provides acceptable accuracy in calculating the two-phase parameters in high-speed flows and can be extended for modeling more complex, multidimensional detonation and propulsion systems.
- Open Access
- 2 July 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (13) , 7450
Numerical Study on Tree Belt Impact on Wind Shear on Agricultural Land
Tree belts are commonly applied over agricultural terrain where seeds of wheat and other vegetation are planted in the ground in order to prevent the seeds from being blown by the wind. The tree belt comprises a long and thin (10–20 m thick) section of trees, which spans in a direction normal to the prevailing wind direction. While serving its agricultural goal, the belt does inevitably modify the boundary layer profile of the wind. This, on its part, is likely to affect the operation of small-scale wind turbines installed in the vicinity of the belt. The goal of this study is to determine the span and range at which this effect manifests itself. It was found that in the near vicinity downstream and slightly above the tree belt, the wind velocity actually increased due to the mass conservation. The flow became independent on the tree belt drag coefficient when its value was higher than 0.2 1/m. The turbulence introduced by the belt was restricted to a height of 1.5–2 tree belts.
- 2 July 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (13) , 7450
Open AccessNumerical Study on Tree Belt Impact on Wind Shear on Agricultural Land
Tree belts are commonly applied over agricultural terrain where seeds of wheat and other vegetation are planted in the ground in order to prevent the seeds from being blown by the wind. The tree belt comprises a long and thin (10–20 m thick) section of trees, which spans in a direction normal to the prevailing wind direction. While serving its agricultural goal, the belt does inevitably modify the boundary layer profile of the wind. This, on its part, is likely to affect the operation of small-scale wind turbines installed in the vicinity of the belt. The goal of this study is to determine the span and range at which this effect manifests itself. It was found that in the near vicinity downstream and slightly above the tree belt, the wind velocity actually increased due to the mass conservation. The flow became independent on the tree belt drag coefficient when its value was higher than 0.2 1/m. The turbulence introduced by the belt was restricted to a height of 1.5–2 tree belts.
- Open Access
Numerical Study of the Torque and Power of a Hydraulic Turbine with Oscillating Blades
This paper presents results from a physical and numerical study of a new type of axial hydraulic turbine with oscillating blades, which is used to utilize wind waves energy. The pilot studies were conducted on a test bench constructed in one of the labs of the “Department of Hydrodynamics and Hydraulic Machines” in the Technical University of Sofia. The numerical computations were performed with the commercial software package Ansys Fluent 2022. The flow has been modeled with the k-ω (SST) turbulence model, whose main advantage is to resolve the viscous sublayer in over refined meshes. A pressure-based solver was used since the fluid is incompressible and the flow velocity is low. The study investigated several different pitch angles of the blades ranging between 0 and 80 deg at prescribed upstream flow velocities from 0.15 m/s to 2.0 m/s. The dependencies of the torque coefficient, power coefficient, and the optimal tip speed ratio on the flow velocity are presented and discussed.
Open AccessNumerical Study of the Torque and Power of a Hydraulic Turbine with Oscillating Blades
This paper presents results from a physical and numerical study of a new type of axial hydraulic turbine with oscillating blades, which is used to utilize wind waves energy. The pilot studies were conducted on a test bench constructed in one of the labs of the “Department of Hydrodynamics and Hydraulic Machines” in the Technical University of Sofia. The numerical computations were performed with the commercial software package Ansys Fluent 2022. The flow has been modeled with the k-ω (SST) turbulence model, whose main advantage is to resolve the viscous sublayer in over refined meshes. A pressure-based solver was used since the fluid is incompressible and the flow velocity is low. The study investigated several different pitch angles of the blades ranging between 0 and 80 deg at prescribed upstream flow velocities from 0.15 m/s to 2.0 m/s. The dependencies of the torque coefficient, power coefficient, and the optimal tip speed ratio on the flow velocity are presented and discussed.
- Open Access
- 1 January 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1128 (1) , 012019
Verification of the capacity of lubricating oil cooler system of turbine bearings
The capacity to cool the lubrication oil of hydraulic turbine bearings by submerged water heat exchangers has been verified. Calculations are done for existing heat exchangers and for retrofit ones. Input data from on-site measurements was used, as well as data for the physical constants. The goal of the study was to prove that the new heat exchangers’ efficiency is not less than that of the existing heat exchangers. The method of analysis elaborated on calculation of convective heat transfer coefficient. This was done for both a forced convection and an inhibited convection setup. It was debated that only the forced convection setup was a factor affecting the difference between both designs.
- 1 January 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1128 (1) , 012019
Open AccessVerification of the capacity of lubricating oil cooler system of turbine bearings
The capacity to cool the lubrication oil of hydraulic turbine bearings by submerged water heat exchangers has been verified. Calculations are done for existing heat exchangers and for retrofit ones. Input data from on-site measurements was used, as well as data for the physical constants. The goal of the study was to prove that the new heat exchangers’ efficiency is not less than that of the existing heat exchangers. The method of analysis elaborated on calculation of convective heat transfer coefficient. This was done for both a forced convection and an inhibited convection setup. It was debated that only the forced convection setup was a factor affecting the difference between both designs.
- Open Access
- 22 November 2021
- Published by EDP Sciences
- Vol. 327, 05001
Modelling indoor pollutant distribution via passive scalar and virtual box approach
The distribution of PM2.5 around a thermal manikin with realistic female body shape in a naturally ventilated room has been modelled. The health risk (HR) due to inhalation of the PM2.5 has been quantified by integrating the pollutants mass flux over the boundaries of a virtual box around the mannequin’s head (the breathing zone). By the same approach HR is evaluated over the boundaries of another virtual box that surrounds the manikins body and defines the occupied zone. The paper focuses on the peculiarities of creating and meshing a virtual geometry, as well as on the application of user-defined functions (UDF) for defining a pollutant source within the room using Ansys Fluent modelling package.
- 22 November 2021
- Published by EDP Sciences
- Vol. 327, 05001
Open AccessModelling indoor pollutant distribution via passive scalar and virtual box approach
The distribution of PM2.5 around a thermal manikin with realistic female body shape in a naturally ventilated room has been modelled. The health risk (HR) due to inhalation of the PM2.5 has been quantified by integrating the pollutants mass flux over the boundaries of a virtual box around the mannequin’s head (the breathing zone). By the same approach HR is evaluated over the boundaries of another virtual box that surrounds the manikins body and defines the occupied zone. The paper focuses on the peculiarities of creating and meshing a virtual geometry, as well as on the application of user-defined functions (UDF) for defining a pollutant source within the room using Ansys Fluent modelling package.
- 24 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Flow Characteristics at The Outlets of Air Terminal Devices
The current work deals with the experimental investigation of flow characteristics at the outlets of a four-way ceiling fan-coil, part of the HVAC system in a university classroom. The time variation of the air velocity was measured under the recirculation mode of operation of the fan-coil. The aim was to assess if the flow characteristics at each outlet of one fan-coil are the same. The measurements were performed at all outlets by an omnidirectional thermoanemometer.
- 24 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Flow Characteristics at The Outlets of Air Terminal Devices
The current work deals with the experimental investigation of flow characteristics at the outlets of a four-way ceiling fan-coil, part of the HVAC system in a university classroom. The time variation of the air velocity was measured under the recirculation mode of operation of the fan-coil. The aim was to assess if the flow characteristics at each outlet of one fan-coil are the same. The measurements were performed at all outlets by an omnidirectional thermoanemometer.
- Open Access
- 18 November 2020
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 207, 02010
Validation study for Large-Eddy Simulation of Forest Flow
The publication presents Large-Eddy Simulation (LES) of flow over a reduced-scale wind tunnel model of a forest canopy. The final aim of the study is to determine factors responsible for damage in forests by strong winds. The wind tunnel forest was represented by an open-porous foam material for the crown layer and wooden dowels for the trunk layer. The forest model was installed in the open test section of a Goettingen-type wind tunnel and Particle Image Velocimetry (PIV) measurements were made for the acquisition of the flow field data. The numerical simulations were performed with OpenFOAM®. The forest was modelled by an additional sink term in the momentum transport equations based on the leaf area density and a characteristic drag coefficient for the underlying tree specimen. Large-eddy simulations with different subgrid-scale (SGS) turbulence models were carried out and compared to wind tunnel data. The Smagorinsky SGS model outperformed the dynamic Lagrangian SGS model in the windward edge region (within a distance of approximately 2 tree heights from the leading edge) whereas the dynamic Lagrangian SGS model showed a better performance for regions farther downstream.
- 18 November 2020
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 207, 02010
Open AccessValidation study for Large-Eddy Simulation of Forest Flow
The publication presents Large-Eddy Simulation (LES) of flow over a reduced-scale wind tunnel model of a forest canopy. The final aim of the study is to determine factors responsible for damage in forests by strong winds. The wind tunnel forest was represented by an open-porous foam material for the crown layer and wooden dowels for the trunk layer. The forest model was installed in the open test section of a Goettingen-type wind tunnel and Particle Image Velocimetry (PIV) measurements were made for the acquisition of the flow field data. The numerical simulations were performed with OpenFOAM®. The forest was modelled by an additional sink term in the momentum transport equations based on the leaf area density and a characteristic drag coefficient for the underlying tree specimen. Large-eddy simulations with different subgrid-scale (SGS) turbulence models were carried out and compared to wind tunnel data. The Smagorinsky SGS model outperformed the dynamic Lagrangian SGS model in the windward edge region (within a distance of approximately 2 tree heights from the leading edge) whereas the dynamic Lagrangian SGS model showed a better performance for regions farther downstream.
- Open Access
- 22 July 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (15) , 5036
On the Procedure of Draught Rate Assessment in Indoor Spaces
The objective of the paper is to demonstrate the importance of the unsteady Computational Fluid Dynamics (CFD) simulations and long-term measurements for the reliable assessment of thermal comfort indoors, for proper categorization of the indoor thermal environment and for identifying the reasons for complaints due to draught discomfort. Numerical simulations and experimental measurements were applied in combination to study ventilation in a field laboratory, a university classroom with a controlled indoor environment. Strong unsteadiness of the airflow was registered both in the unsteady RANS results and the real-scale long-term velocity data measured with thermo anemometer. Low-frequency high-amplitude velocity fluctuations observed lead to substantial time variation of the draught rate. In case of categorization of a thermal environment, the point measurements or steady-state RANS computations would lead to wrong conclusions as well as they cannot be used for identification of the reasons for people’s complaints due to draught discomfort if strong unsteadiness of the airflow exists. It is demonstrated that the length of the time interval for draught rate (DR) assessment may not be universal if low-frequency high-amplitude pulsations are present in the room airflow.
- 22 July 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (15) , 5036
Open AccessOn the Procedure of Draught Rate Assessment in Indoor Spaces
The objective of the paper is to demonstrate the importance of the unsteady Computational Fluid Dynamics (CFD) simulations and long-term measurements for the reliable assessment of thermal comfort indoors, for proper categorization of the indoor thermal environment and for identifying the reasons for complaints due to draught discomfort. Numerical simulations and experimental measurements were applied in combination to study ventilation in a field laboratory, a university classroom with a controlled indoor environment. Strong unsteadiness of the airflow was registered both in the unsteady RANS results and the real-scale long-term velocity data measured with thermo anemometer. Low-frequency high-amplitude velocity fluctuations observed lead to substantial time variation of the draught rate. In case of categorization of a thermal environment, the point measurements or steady-state RANS computations would lead to wrong conclusions as well as they cannot be used for identification of the reasons for people’s complaints due to draught discomfort if strong unsteadiness of the airflow exists. It is demonstrated that the length of the time interval for draught rate (DR) assessment may not be universal if low-frequency high-amplitude pulsations are present in the room airflow.