Khairul Khuzaimah Abdul Rahim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Khairul Khuzaimah Abdul Rahim has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Ahmad Nurfaidhi Rizalman
Universiti Malaysia Sabah
2 shared publications - Badorul Hisham Abu Bakar
School of Civil Engineering, Universiti Sains Malaysia, Engineering Campus , Nibong Tebal , 14300 , Pulau Pinang , Malaysia
2 shared publications - Gaddafi Ismaili2 shared publications
- Gaddafi Ismaili
Department of Civil Engineering, Faculty of Engineering, Universiti Malaysia Sarawak, Kota Samarahan 94300, Sarawak, Malaysia
2 shared publications - Iskanda Openg
Faculty of Civil Engineering, Universiti Teknologi MARA, Kota Samarahan 94300, Malaysia
2 shared publications - Meekiong Kalu
Department of Plant Resource Science and Management, Faculty Resource Science & Technology, Universiti Malaysia Sarawak, Kota Samarahan 94300, Sarawak, Malaysia
2 shared publications
Latest Publications
- Open Access
The Mechanical Strength Properties, Treatability Retention and Hazard Classification of Treated Small-Clear Fast-Growing Acacia mangium Superbulk at Different Age Groups
The slow growth rate of primer species has affected the supply available to accommodate the market demand. To overcome these problems, a study was carried out to fully utilise fast-growing timber as the primary resource to ensure the demand for timber logs continues. This paper aimed to determine mechanical strength properties, treatability retention, and hazard classification of 7-, 10- and 13-year-old small-clear samples of Acacia mangium superbulk collected from Daiken Plantation Sdn. Bhd. Bintulu, Sarawak, following treatment with 10% copper chrome arsenic. As a result of this study, the maximum strength was obtained from the 10-year-old age group, with the modulus of rupture (MOR), the modulus of elasticity (MOE), and compression parallel to the grain values of small-clear treated Acacia mangium superbulk reaching 118.76 N/mm2, 15,020 N/mm2, and 57.82 N/mm2, respectively. In addition, the treatability retentions obtained were 149.27 L/m3, 147.25 L/m3, and 141.09 L/m3, which were recorded from the 7-, 10-, and 13-year-old samples, respectively. Meanwhile, the dry-salt retentions obtained from the 7-, 10- and 13-year-old samples were 14.93 kg/m3, 14.73 kg/m3, and 14.11 kg/m3, respectively. Hence, this species is classified as moderately difficult to treat under CCA (treatability retention: 80–160 L/m3) and is categorised under the hazard class of H4 (dry salt retention: 12–16 kg/m3).
Open AccessThe Mechanical Strength Properties, Treatability Retention and Hazard Classification of Treated Small-Clear Fast-Growing Acacia mangium Superbulk at Different Age Groups
The slow growth rate of primer species has affected the supply available to accommodate the market demand. To overcome these problems, a study was carried out to fully utilise fast-growing timber as the primary resource to ensure the demand for timber logs continues. This paper aimed to determine mechanical strength properties, treatability retention, and hazard classification of 7-, 10- and 13-year-old small-clear samples of Acacia mangium superbulk collected from Daiken Plantation Sdn. Bhd. Bintulu, Sarawak, following treatment with 10% copper chrome arsenic. As a result of this study, the maximum strength was obtained from the 10-year-old age group, with the modulus of rupture (MOR), the modulus of elasticity (MOE), and compression parallel to the grain values of small-clear treated Acacia mangium superbulk reaching 118.76 N/mm2, 15,020 N/mm2, and 57.82 N/mm2, respectively. In addition, the treatability retentions obtained were 149.27 L/m3, 147.25 L/m3, and 141.09 L/m3, which were recorded from the 7-, 10-, and 13-year-old samples, respectively. Meanwhile, the dry-salt retentions obtained from the 7-, 10- and 13-year-old samples were 14.93 kg/m3, 14.73 kg/m3, and 14.11 kg/m3, respectively. Hence, this species is classified as moderately difficult to treat under CCA (treatability retention: 80–160 L/m3) and is categorised under the hazard class of H4 (dry salt retention: 12–16 kg/m3).
- Open Access
Physical and Mechanical Properties Performance between Untreated and Treated with CCA Treatment at Different Age Groups of Fast-Growing Acacia Hybrid of Sarawak
An effort was carried out to fully utilise fast-growing Acacia hybrid usage in the timber engineering field; however, the research data are still lacking. This paper aims to evaluate the physical and mechanical properties performance between untreated (control) and treated with 10% copper chrome arsenic of Acacia hybrid collected from Daikin Plantation Sdn. Bhd. Bintulu, Sarawak at air-dry condition at different age groups using the small clear method. Mechanical properties test refers to shear parallel to grain (tangential and radial directions), cleavage (tangential and radial directions), and tension parallel to grain test. Meanwhile, the physical properties test refers to moisture content (MC) and density test. After treatment, mechanical properties increase with an average of 13.67%; meanwhile, moisture content decreased with an average of 0.58% or 0.09% MC, and density slightly increased with an average of 0.44% or 0.002 g/cm3. Results indicate that 10-year-old Acacia hybrid exhibits the highest strength values in shear parallel to the grain, tension parallel to the grain, and cleavage, followed by 13-year-old and 7-year-old. Treated samples in the tangential direction performed better with consistent mean results than that of the untreated samples, while radial direction gave a high average strength increment when treated.
Open AccessPhysical and Mechanical Properties Performance between Untreated and Treated with CCA Treatment at Different Age Groups of Fast-Growing Acacia Hybrid of Sarawak
An effort was carried out to fully utilise fast-growing Acacia hybrid usage in the timber engineering field; however, the research data are still lacking. This paper aims to evaluate the physical and mechanical properties performance between untreated (control) and treated with 10% copper chrome arsenic of Acacia hybrid collected from Daikin Plantation Sdn. Bhd. Bintulu, Sarawak at air-dry condition at different age groups using the small clear method. Mechanical properties test refers to shear parallel to grain (tangential and radial directions), cleavage (tangential and radial directions), and tension parallel to grain test. Meanwhile, the physical properties test refers to moisture content (MC) and density test. After treatment, mechanical properties increase with an average of 13.67%; meanwhile, moisture content decreased with an average of 0.58% or 0.09% MC, and density slightly increased with an average of 0.44% or 0.002 g/cm3. Results indicate that 10-year-old Acacia hybrid exhibits the highest strength values in shear parallel to the grain, tension parallel to the grain, and cleavage, followed by 13-year-old and 7-year-old. Treated samples in the tangential direction performed better with consistent mean results than that of the untreated samples, while radial direction gave a high average strength increment when treated.
- Open Access
- 1 December 2011
- Published by UNIMAS Publisher in Journal of Civil Engineering, Science and Technology
- Vol. 2 (2) , 48-52
The Behavior of Strength Properties from Three Different Tree Boles of Aras in Sarawak
Aras had been selected and tested in small clear specimens. Sampling of test specimens are made from three sections of the tree bole namely from bottom, middle, and top parts. This paper looks into the information of strength properties from three sections of sampled. The strength properties test required are the modulus of rupture, modulus of elasticity and compression stress parallel to grain. Meanwhile, the physical properties' test referred to moisture content and basic density. The testing conducted in two different conditions of the trees, which were referred to green and air-dry condition. It was found that the average mean values for modulus of rupture, modulus of elasticity and compressive stress parallel to grain tested at green condition were 47.52N/mm2, 6358.56N/mm2 and 22.42N/mm2 respectively meanwhile at air-dry condition were 70.49N/mm2, 8217.64N/mm2 and 34.07N/mm2 respectively. Meanwhile, the average mean values for moisture content at green condition were 83.34% whilst at the air-dry condition were 12.33%. Basic density remains unchanged from both conditions.
- 1 December 2011
- Published by UNIMAS Publisher in Journal of Civil Engineering, Science and Technology
- Vol. 2 (2) , 48-52
Open AccessThe Behavior of Strength Properties from Three Different Tree Boles of Aras in Sarawak
Aras had been selected and tested in small clear specimens. Sampling of test specimens are made from three sections of the tree bole namely from bottom, middle, and top parts. This paper looks into the information of strength properties from three sections of sampled. The strength properties test required are the modulus of rupture, modulus of elasticity and compression stress parallel to grain. Meanwhile, the physical properties' test referred to moisture content and basic density. The testing conducted in two different conditions of the trees, which were referred to green and air-dry condition. It was found that the average mean values for modulus of rupture, modulus of elasticity and compressive stress parallel to grain tested at green condition were 47.52N/mm2, 6358.56N/mm2 and 22.42N/mm2 respectively meanwhile at air-dry condition were 70.49N/mm2, 8217.64N/mm2 and 34.07N/mm2 respectively. Meanwhile, the average mean values for moisture content at green condition were 83.34% whilst at the air-dry condition were 12.33%. Basic density remains unchanged from both conditions.
- Open Access
- 1 December 2011
- Published by UNIMAS Publisher in Journal of Civil Engineering, Science and Technology
- Vol. 2 (2) , 17-22
Evaluation of Acacia Mangium in Structural Size at Green Condition
Acacia mangium is one of the most popular choices in the reforestation and rehabilitation of abandoned shifting cultivation areas dated back to the 70’s. This paper looks into the evaluation of mechanical strength and physical properties in structural size at green condition for Acacia mangium. The mechanical strength properties tests were referred to the modulus of rupture, modulus of elasticity and tensile strength. Meanwhile, physical properties determination referred to basic density and moisture content. At green condition, Acacia mangium had been identified under the strength group SG6. It was found that strength value of modulus of rupture was higher than the tensile strength value with 44% stronger in bending compared to in tension. At the structural size, the mean value for moisture content and basic density at green condition were reported with 73.03% and 0.54g/cm3 respectively.
- 1 December 2011
- Published by UNIMAS Publisher in Journal of Civil Engineering, Science and Technology
- Vol. 2 (2) , 17-22
Open AccessEvaluation of Acacia Mangium in Structural Size at Green Condition
Acacia mangium is one of the most popular choices in the reforestation and rehabilitation of abandoned shifting cultivation areas dated back to the 70’s. This paper looks into the evaluation of mechanical strength and physical properties in structural size at green condition for Acacia mangium. The mechanical strength properties tests were referred to the modulus of rupture, modulus of elasticity and tensile strength. Meanwhile, physical properties determination referred to basic density and moisture content. At green condition, Acacia mangium had been identified under the strength group SG6. It was found that strength value of modulus of rupture was higher than the tensile strength value with 44% stronger in bending compared to in tension. At the structural size, the mean value for moisture content and basic density at green condition were reported with 73.03% and 0.54g/cm3 respectively.