TFTimur V. Filippov

Timur V. Filippov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Timur V. Filippov has a total of 54 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Balanced Comparator as a Benchmark Circuit to Validate Josephson Simulators

    by Timur V. Filippov, Sukanya S. Meher, M. Eren Çelik, Dmitri E. Kirichenko, Anubhav Sahu, Aaron J. Barker, Stephen R. Whiteley

    The balanced comparator (BC), a pair of Josephson junctions, is a key building block and decision-making element for the rapid single flux quantum (RSFQ) logic cells. The properties of the BC define the maximum clock frequency and bit error rate of RSFQ cells and circuits. Comparators are well characterized by two parameters, the gray zone (GZ) and the gray zone threshold (GZT). Both parameters depend on the dynamic properties of a pair of junctions forming the BC and its surrounding circuitry. In addition, the gray zone depends on the thermal noise in Josephson junctions. The GZ and GZT parameters can be easily measured for various BCs and be used for model-to-hardware correlations. This makes the BC a unique circuit to validate and calibrate any Josephson simulator by comparing measured and simulated characteristics, including both dynamic and noise properties. In this article, we used a set of BCs designed for the SFQ5ee fabrication process at MIT Lincoln Laboratory to validate and calibrate the Synopsys PrimeSim HSPICE simulator. We were able to match experimental and simulated results and reproduce in simulations the main features observed experimentally and predicted theoretically. A list of recommended design variations to validate a Josephson simulator is provided.

  • The Josephson Balanced Comparator as a Sensor to Monitor Clock Sources for RSFQ/ERSFQ Circuits

    by Timur V. Filippov, Dmitri E. Kirichenko, Anubhav Sahu, M. Eren Çelik, Yuri A. Polyakov, Deepnarayan Gupta

    The Josephson balanced comparator (BC) is a key component for all RSFQ/ERSFQ logic cells. Its frequency-dependent properties (gray zone and threshold current value) define the maximum clock frequency and bit error rate (BER) of RSFQ/ERSFQ circuits. The balanced comparator can also be used for various monitoring purposes. In this paper, we focus on clock sources and analyze several of them by means of BCs. We show experimentally how local overheating, associated with sub-optimally designed analog clock sources, can compromise the HF performance of a balanced comparator as well as an RFSQ/ERSFQ circuit on the same chip. We also investigate a clock source based on an external HF generator followed by an on-chip DC/SFQ converter and a frequency doubler. We use the balanced comparator's performance to optimize the on-chip part of the clock source at HF. In addition, we verify the advantage of overshunting the comparator driver to achieve higher clock frequency and lower BER. All test circuits were designed for the SFQ5ee fabrication node at MIT-LL, but conclusions can be applied to other fabrication processes.


  • Experimental Evaluation of Josephson Balanced Comparators Toward 100 GHz RSFQ Circuits

    by Timur V. Filippov, Anubhav Sahu, Dmitri E. Kirichenko, M. Eren Çelik, Deepnarayan Gupta

    The Josephson balanced comparator (BC) is a decision-making element and a key building block for all RSFQ logic cells. The comparator is usually characterized by two parameters: gray zone and threshold value. Both parameters depend on the comparator's design, the design of a BC's driver, as well as temperature and frequency of operation. In this paper, we focus on the high-frequency properties of the balanced comparators designed for the Nb SFQ5ee fabrication node at MIT-LL. RSFQ circuits, fabricated at this node, operate nowadays routinely at about 50 GHz. We demonstrate that a further increase of the operational frequency up to 75 GHz with a bit-error rate (BER) of 10 -14 can be achieved by optimizing the comparator's driver design. We estimate BER of 10 -3 at 100 GHz, which is not enough for complex circuits. An acceptable BER at 100 GHz requires additional optimization of design and fab.


  • Power Optimization of 50 GHz ERSFQ Circuits

    by Mustapha M. Habib, Timur V. Filippov, Anubhav Sahu, Dmitri E. Kirichenko, A. Erik Lehmann, Deepnarayan Gupta

    The Energy-efficient Rapid Single Flux Quantum (ERSFQ) logic family offers zero-static power dissipation. Any ERSFQ circuit requires a feeding Josephson transmission line (FJTL), a relatively large active transmission line, which serves as an accurate voltage source. For proper operation, the FJTL needs to be continuously pumped at a frequency that is equal to or higher than the highest clock frequency of the ERSFQ circuit. We selected an on-chip pseudo-random binary sequence (PRBS) generator as the example circuit since it naturally facilitates quantitative measurements of operating bias margins in terms of bit error rate (BER). Using external and internal flux pump sources, we performed extensive experimental studies on BER for ERSFQ PRBS generators operating at clock frequencies up to 50 GHz. We paid special attention to the over-pumping regime, where the FJTL pump frequency is higher than the PRBS clock frequency and confirmed its superiority in improving BER. At 35.56 GHz clock frequency, a group of 4 PRBS generators and 4 individual FJTLs with the bias current ratio (BCR) equal to 1, had a BER lower than 10 -12 and bias margins of ±25% for internal and external flux pump sources over-pumping at 6.25% above clock frequency. The maximal operational clock frequency of a single ERSFQ PRBS generator with intrinsic pump source (+6.25% over-pumping) and BER -12 was 49.53 GHz. We also focused on optimization of the FJTL's size to reduce the power consumption and the area occupied by the FJTL itself. All chips were fabricated at MIT-Lincoln Laboratory using the SFQ5ee fab node. Future steps required for better understanding of ERSFQ operation are discussed.


  • 60-GHz Single Flux Quantum Pulse Transfer Circuit for Serial Biasing

    by Ashish Shukla, Dmitri E. Kirichenko, Timur V. Filippov, Anubhav Sahu, A. Erik Lehmann, Mingoo Seok, Deepnarayan Gupta

    Serial Biasing (SB) is a technique to reduce the total DC bias current of Rapid Single Flux Quantum (RSFQ) circuits by partitioning a design into several islands with isolated grounds and sequential biasing. In this paper we focus on the design of a driver-receiver pair (DRP) to transfer pulses between islands that are galvanically isolated for pulse streams. We discuss both DRP itself and the structure for its testing, that comprises several DRPs connected in series, on-chip pseudo random binary sequence (PRBS) generator for circuit stimulation, and HF output interface. We use the layout of DRPs' chain as an example to illustrate the advantage of the grapevine (GV) approach, introduced earlier, to manage the bias current flowing into and out of an island. The GV current management technique is analyzed by both electromagnetic simulations and measurement, compared, and contrasted with the so-called ‘straightforward’ (SF) approach. The maximum operational frequency for SF test structure was 10 GHz with zero margins for the SB current. Measurements of the GV structure at 10 GHz demonstrated BER of 10 -12 with ±5.8% margins for SB current. We observed the correct operation of the 5-island DRP chain up to 60 GHz using the grapevine approach for SB current management. All chips were fabricated at MIT Lincoln Laboratory using SFQ5ee fab node.


  • Serial Biasing Technique for Electronic Design Automation in RSFQ Circuits

    by Ashish Shukla, Timur V. Filippov, Dmitri E. Kirichenko, Sukanya S. Meher, Mustafa Eren Celik, Mingoo Seok, Deepnarayan Gupta

    There has been renewed interest and efforts in increasing the complexity of superconductor circuits by means of electronic design automation (EDA). Serial Biasing (SB) is a technique that reduces the total DC bias current required by large Rapid Single Flux Quantum (RSFQ) circuits, including its energy-efficient variant, ERSFQ. We believe SB needs to be incorporated in any EDA flow for large circuits. In SB, equally biased circuit blocks are placed on galvanically isolated islands and biased in series. SFQ pulses are transferred between islands by means of driver-receiver pairs (DRPs). The special current management technique, called the grapevine (GV) approach and introduced earlier, is used to handle the bias current flowing in and out of an island. In this paper, we present all required layout primitives needed to implement SB for the IARPA-led SuperTools (ST) cell library that targets the SFQ5ee fab node at MIT Lincoln Laboratory. We discuss the horizontal and vertical composite driver-receiver pairs (CDRPs) that comprise not only DRPs but also transmitters and receivers for passive transmission lines (PTLs). We present the basic blocks to implement the GV managing technique for current injection and extraction. As a proof of concept, we designed a 4-island test circuit that comprises all discussed layout primitives and employs an on-chip pseudo-random binary sequence (PRBS) generator as a test pattern source. The test circuit worked up to 50 GHz at the BER level of 10 -12 . We discuss future steps to improve the SB technique.


  • Pulse Interfaces and Current Management Techniques for Serially Biased RSFQ Circuits

    by Ashish Shukla, Dmitri E. Kirichenko, Timur V. Filippov, Anubhav Sahu, M. Eren Çelik, Mingoo Seok, Deepnarayan Gupta

    As digital superconductor circuits based on Rapid Single Flux Quantum (RSFQ) logic scale up in complexity, so does the total current required to provide dc bias. Serial biasing (SB) is a promising solution that can be used to reduce the current by placing identical digital blocks on islands with isolated grounds and bias them sequentially. There are typically two implementations that are essential for the SB approach: the design of a driver-receiver pair (DRP) for inter-island pulse transport and the current management technique to handle the bias current flowing into and out of an island. While a DRP with good fidelity is essential for any serially biased circuit, the current management becomes critical for designs with relatively large bias current. In this paper, we address the latter. First, we propose a grapevine biasing scheme for serial bias current management. Second, we implement the technique using two exemplar circuits: the parallel counter and the digital decimation filter. We report the low and high speed test results up to 50 GHz for both circuits fabricated at MIT-LL in the SFQ5ee 10 kA/2 Ω fab node.


  • 25-GHz Operation of ERSFQ Time-to-Digital Converter

    by Mustafa Eren Celik, Timur V. Filippov, Dmitri Kirichenko, Mustapha Habib, Andrei Talalaevskii, Anubhav Sahu, Deepnarayan Gupta

    Fast time-to-digital converters (TDCs), used to convert a continuous time interval into discrete number for further processing, serve diverse applications ranging from photon/particle detectors to communication systems employing delay-encoded pulses. Being a multi-rate digital circuit, the TDC is also a good candidate to explore operation of Energy-Efficient Rapid Single Flux Quantum (ERSFQ) circuits at high (>10 GHz) clock frequency. We de-signed a TDC using ERSFQ cells, targeting the 10-kA/cm2 SFQ5ee fabrication process at MIT Lincoln Laboratory. The main elements of the circuit comprise a 9-bit binary ripple counter and a parallel-to-serial converter. A frequency divider and a pulse distribution network with a decision-making element are designed to control the operation. The ERSFQ TDC was operated up to 25 GHz clock frequency (40 ps time resolution) and with a power consumption of around 14 W for all ERSFQ components. The design specifications such as number of junctions and area will be discussed together with the power delivery technique involving an over-pumped feeding Josephson transmission line (JTL).


  • Gray Zone and Threshold Current Measurements of the Josephson Balanced Comparator

    by Timur V. Filippov, Anubhav Sahu, M. Eren Çelik, Dmitri E. Kirichenko, Mustapha Habib, Deepnarayan Gupta

    The Josephson balanced comparator, a decision-making circuit comprising two Josephson junctions (JJs) connected in series from a clocking perspective and in parallel for the current to be measured, is ubiquitous in single flux quantum (SFQ) logic. Its noise properties are crucial for the performance of logic devices. The characteristics of the balanced comparator can also be used to monitor fab process and design implementation as an indicator for excess noise, overheating, linearity, dynamic effects, etc. We designed several test structures to measure gray zone of various comparators fabricated in different nodes of process at MIT-LL. We used digital circuitry to measure comparator characteristics at low frequencies and an analog testbed to perform high frequency characterization. Experimental results for gray zone of comparators designed for fabrication nodes with different current densities, sheet resistances, critical damping are presented and studied as a function of clock frequency.


  • Development of Superconductor Advanced Integrated Circuit Design Flow Using Synopsys Tools

    by Amol Inamdar, Jushya Ravi, Sukanya. S. Meher, Stephen Miller, M. Eren Çelik, A. Erik Lehmann, Sam Lo, Aaron Barker, Stephen Whiteley, Nisha Johnson, et al.

    HYPRES developed an advanced design flow and design infrastructure for single-flux-quantum (SFQ) superconductor integrated circuits using standard CMOS based EDA tools along with internally developed tools and has been successfully using this flow for the past several years. The design infrastructure includes the process design kit, advanced simulation methodology, and IC verification rule decks. The superconductor hierarchical circuit analyzer developed by HYPRES serves as bedrock of our simulation methodology facilitating circuit analysis and debugging including extraction of circuit parameter margins, analysis of Monte-Carlo simulations with process corners, as well as automated timing characterization. Using this proven design flow and infrastructure as a knowledge source, we have collaborated with Synopsys to enhance their tools for a full native tool enabled design flow and infrastructure, which represents a significant expansion in design capabilities and capacity for superconducting electronics. Using the 64-Bit arithmetic logic unit and a Pseudo Random Bit Sequence (PRBS) generator as reference circuits, we demonstrate the use of Synopsys tools for superconductor IC design including spice circuit simulations, plotting waveforms, margins analysis, Monte-Carlo simulations, HDL simulations with timing back-annotation, and IC validation including design rule checker and layout-versus-schematic checker.