Giuseppe Taddia
Research Subjects
Research Interests
Giuseppe Taddia has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Alessandro Lampasi
ENEA and DTT S. c. a r. l., Frascati, Italy
3 shared publications - Sandro M. Tenconi
OCEM Power Electronics, Bologna, Italy
2 shared publications - Antti Jokinen
Fusion for Energy (F4E), Boltzmannstrasse 2, 85748 Garching, Germany
1 shared publication - Filippo Burini
OCEM Power Electronics, Via della Solidarietà, 2/1/Località Crespellano, Valsamoggia, 40056 Bologna, Italy
1 shared publication Filippo Gherdovich
OCEM Power Electronics, Valsamoggia, Italy
1 shared publication- Filippo Gherdovich
OCEM Power Electronics, Bologna, Italy
1 shared publication
Latest Publications
- 28 March 2019
- Published by Elsevier in Fusion Engineering and Design
- Vol. 146, 1921-1925
A new generation of power supplies for pulsed loads
- 28 March 2019
- Published by Elsevier in Fusion Engineering and Design
- Vol. 146, 1921-1925
A new generation of power supplies for pulsed loads
- 9 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (10) , 3393-3400
Compact Power Supply With Integrated Energy Storage and Recovery Capabilities for Arbitrary Currents up to 2 kA
In many relevant cases requiring a net energy comparable with that of a household appliance, the power supplies (PSs) and the electrical systems must be oversized to sustain short peak demands. The same equivalent energy could be achieved by storing and distributing the power over the time. These considerations lead to a new PS concept based on the exploitation of the energy stored between the actual operations. The new compact ( $60\,\,\text {cm} \times 120\,\,\text {cm} \times 190$ cm) PS is able to generate arbitrary currents up to 2 kA by an integrated energy storage system based on supercapacitors. The delivered output power (approximately 200 kW) is obtained from a very low and tunable input power (<1 kW). Furthermore, a portion of the injected power can be recovered in the storage system. Even though the system was designed for a specific project (the PROTO-SPHERA spherical tokamak), the presented approach can be applied to general-purpose PSs, and there are encouraging prospects to extend it to large facilities with higher currents and voltages.
- 9 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (10) , 3393-3400
Compact Power Supply With Integrated Energy Storage and Recovery Capabilities for Arbitrary Currents up to 2 kA
In many relevant cases requiring a net energy comparable with that of a household appliance, the power supplies (PSs) and the electrical systems must be oversized to sustain short peak demands. The same equivalent energy could be achieved by storing and distributing the power over the time. These considerations lead to a new PS concept based on the exploitation of the energy stored between the actual operations. The new compact ( $60\,\,\text {cm} \times 120\,\,\text {cm} \times 190$ cm) PS is able to generate arbitrary currents up to 2 kA by an integrated energy storage system based on supercapacitors. The delivered output power (approximately 200 kW) is obtained from a very low and tunable input power (<1 kW). Furthermore, a portion of the injected power can be recovered in the storage system. Even though the system was designed for a specific project (the PROTO-SPHERA spherical tokamak), the presented approach can be applied to general-purpose PSs, and there are encouraging prospects to extend it to large facilities with higher currents and voltages.
- Open Access
Installation, Commissioning and Tests of Four Fast Switching Units of up to 20 kA for the JT-60SA Nuclear Fusion Experiment
The nuclear fusion project JT-60SA is presently under construction in Naka (Japan) as a joint collaboration between Europe and Japan, within the framework of the Broader Approach Agreement. According to such agreement, the various JT-60SA systems are supplied by European and Japanese institutions. In particular, the Italian Agency ENEA was in charge for the procurement of the four Switching Network Units (SNUs) for the JT-60SA Central Solenoid (CS). The main SNU function is to interrupt a DC current up to 20 kA in a short time (less than 1 ms) in order to produce an overvoltage of up to 5 kV, crucial to generate and sustain the fusion plasma. The SNU design, manufacturing and factory test activities have been completed in 2016. After the delivery in Naka, the four SNUs have been installed and successfully commissioned in 2017. After an overview on the main technical characteristics of the SNUs and the key aspects of their design, this paper describes the activities performed on-site, highlighting the results obtained during the final acceptance tests and comparing them with the design simulation and the factory test results.
Open AccessInstallation, Commissioning and Tests of Four Fast Switching Units of up to 20 kA for the JT-60SA Nuclear Fusion Experiment
The nuclear fusion project JT-60SA is presently under construction in Naka (Japan) as a joint collaboration between Europe and Japan, within the framework of the Broader Approach Agreement. According to such agreement, the various JT-60SA systems are supplied by European and Japanese institutions. In particular, the Italian Agency ENEA was in charge for the procurement of the four Switching Network Units (SNUs) for the JT-60SA Central Solenoid (CS). The main SNU function is to interrupt a DC current up to 20 kA in a short time (less than 1 ms) in order to produce an overvoltage of up to 5 kV, crucial to generate and sustain the fusion plasma. The SNU design, manufacturing and factory test activities have been completed in 2016. After the delivery in Naka, the four SNUs have been installed and successfully commissioned in 2017. After an overview on the main technical characteristics of the SNUs and the key aspects of their design, this paper describes the activities performed on-site, highlighting the results obtained during the final acceptance tests and comparing them with the design simulation and the factory test results.