Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Chunjiang Li
Department of Geography and Planning, University of Toronto – St. George, Toronto, ON, Canada
1 shared publication Hongyu Tian
School of Mechanical and Aerospace Engineering, Jilin University 1 , Changchun 130025, China
1 shared publication- Jianfang Liu
School of Life Science and Technology, Wuhan Polytechnic University, Wuhan 430023, China
1 shared publication Qingqing Lv
School of Mechanical and Aerospace Engineering, Jilin University 1 , Changchun 130025, China
1 shared publicationShoudong Gu
School of Mechanical and Aerospace Engineering, Jilin University 1 , Changchun 130025, China
1 shared publication- Zhigang Yang
Key Laboratory of Traffic Safety on Track, Ministry of Education, School of Traffic & Transportation Engineering, Central South University, Changsha 410075, China
1 shared publication
Latest Publications
- Open Access
- 1 April 2019
- Published by AIP Publishing in AIP Advances
- Vol. 9 (4) , 045302
Influence of needle impact velocity on the jetting effect of a piezoelectric needle-collision jetting dispenser
Many scholars have conducted in-depth analysis on relevant factors that affect the accuracy of jet dispensing. However, research on the influence of needle impact velocity on jetting performance is limited. Thus, a piezoelectric needle-collision dispenser for micro-droplet jetting is designed in this study, and the influence of the needle impact velocity on jetting effect is deeply analyzed. Initially, the principle of droplet formation and injection is analyzed by Fluent simulation. Thereafter, the mathematical model of the droplet velocity in the nozzle orifice is derived, and the influence of the needle impact velocity on the jetting performance is simulated and analyzed. Results show that the needle impact velocity has an influence on the jetting effect. A prototype of the jetting dispenser is subsequently fabricated, and the needle impact velocity is tested with laser micrometer. The relationship between the needle impact velocity and droplet weight and its corresponding ejected effect are obtained through experimental research. Finally, a UV glue with viscosity of 5,000 cps can be ejected with a minimum average diameter of 272.1 μm by using a needle with a radius of 0.5 mm, a nozzle with a diameter of 50 μm, a taper angle of 90°, a supply pressure of 0.2 Mpa, and a needle impact velocity of 0.13 m/s. The variation of the droplet diameter is within ±2.5%.
- 1 April 2019
- Published by AIP Publishing in AIP Advances
- Vol. 9 (4) , 045302
Open AccessInfluence of needle impact velocity on the jetting effect of a piezoelectric needle-collision jetting dispenser
Many scholars have conducted in-depth analysis on relevant factors that affect the accuracy of jet dispensing. However, research on the influence of needle impact velocity on jetting performance is limited. Thus, a piezoelectric needle-collision dispenser for micro-droplet jetting is designed in this study, and the influence of the needle impact velocity on jetting effect is deeply analyzed. Initially, the principle of droplet formation and injection is analyzed by Fluent simulation. Thereafter, the mathematical model of the droplet velocity in the nozzle orifice is derived, and the influence of the needle impact velocity on the jetting performance is simulated and analyzed. Results show that the needle impact velocity has an influence on the jetting effect. A prototype of the jetting dispenser is subsequently fabricated, and the needle impact velocity is tested with laser micrometer. The relationship between the needle impact velocity and droplet weight and its corresponding ejected effect are obtained through experimental research. Finally, a UV glue with viscosity of 5,000 cps can be ejected with a minimum average diameter of 272.1 μm by using a needle with a radius of 0.5 mm, a nozzle with a diameter of 50 μm, a taper angle of 90°, a supply pressure of 0.2 Mpa, and a needle impact velocity of 0.13 m/s. The variation of the droplet diameter is within ±2.5%.