André Schulze
André Schulze has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Erman Tekkaya
TU Dortmund
5 shared publications A. Erman Tekkaya
3 shared publications- Christoph Dahnke
Bulk metal forming, Institute of Forming Technology and Lightweight Components, Baroper Straße 303, Dortmund, 44227, GERMANY
2 shared publications - Lola Lilensten
Max-Planck-Institut für Eisenforschung Max-Planck Straße 1 40237 Düsseldorf Germany
2 shared publications Mathilde Laurent-Brocq
2 shared publicationsOliver Hering
Institute of Forming Technology and Lightweight Components (IUL), TU Dortmund University, Dortmund, Germany
2 shared publications
Latest Publications
- Open Access
- 5 August 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 944
Analysis of the mechanical damage of a solid-state recycled aluminium alloy under tensile loading
- 5 August 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 944
Open AccessAnalysis of the mechanical damage of a solid-state recycled aluminium alloy under tensile loading
- 2 August 2023
- Published by Elsevier in Materialia
- Vol. 31
Solid state recycling of aluminium chips: Multi-technique characterization and analysis of oxidation
- 2 August 2023
- Published by Elsevier in Materialia
- Vol. 31
Solid state recycling of aluminium chips: Multi-technique characterization and analysis of oxidation
- 1 December 2022
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (1) , 1-29
Controlling Damage Evolution in Geometrically Identical Cold Forged Parts by Counterpressure
It is investigated to what extent the evolution of ductile damage in cold forging can be controlled without changing the geometry of the produced part. Besides the effects of strain hardening and residual stresses, damage, which is the nucleation, growth and coalescence of voids on microscopic level, affects product properties of the manufactured components such as fatigue strength, impact strength, or elastic stiffness. Former investigations have shown that the load path-dependent damage evolution in forward rod extrusion, and thus, the performance of produced parts can be controlled by the process parameters extrusion strain and shoulder opening angle. As these parameters also affect the geometry of extruded parts, design requirements of components might be violated by varying these. Thus, counterpressure is used to superpose purely hydrostatic stresses to forward rod extrusion in order to decrease triaxiality in the forming zone without causing geometric variations in the produced parts. The counterpressure is either introduced by a counterpunch or by modified process routes. The achieved improvements in product performance are in agreement with results obtained by variation of extrusion strain and shoulder opening angle as described in the literature. In addition, it is observed in tensile tests that damage in cold extruded parts does not significantly affect flow stress. All advancements in product performance are realized without affecting the products’ geometries.
- 1 December 2022
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (1) , 1-29
Controlling Damage Evolution in Geometrically Identical Cold Forged Parts by Counterpressure
It is investigated to what extent the evolution of ductile damage in cold forging can be controlled without changing the geometry of the produced part. Besides the effects of strain hardening and residual stresses, damage, which is the nucleation, growth and coalescence of voids on microscopic level, affects product properties of the manufactured components such as fatigue strength, impact strength, or elastic stiffness. Former investigations have shown that the load path-dependent damage evolution in forward rod extrusion, and thus, the performance of produced parts can be controlled by the process parameters extrusion strain and shoulder opening angle. As these parameters also affect the geometry of extruded parts, design requirements of components might be violated by varying these. Thus, counterpressure is used to superpose purely hydrostatic stresses to forward rod extrusion in order to decrease triaxiality in the forming zone without causing geometric variations in the produced parts. The counterpressure is either introduced by a counterpunch or by modified process routes. The achieved improvements in product performance are in agreement with results obtained by variation of extrusion strain and shoulder opening angle as described in the literature. In addition, it is observed in tensile tests that damage in cold extruded parts does not significantly affect flow stress. All advancements in product performance are realized without affecting the products’ geometries.
- Open Access
- 24 February 2022
- Published by Springer Nature in International Journal of Material Forming
- Vol. 15 (2) , 1-13
Extending the potentials of draw-forging
Composite components combine the benefits of different materials, leading to improved product properties, enhanced resource- and energy efficiency and widening the product spectrum. Draw-forging is the unique combination of deep-drawing and cold forging, where a core material is encapsulated within a thin sheet metal blank. Previously, the basic draw-forging process only allowed covering of the shaft tip, and the covered length was limited by the maximum drawing ratio of the sheet. In this work, the different failure types, including tearing of the sheet, asymmetric encapsulation, and the development of a gap in the transition zone were investigated numerically and experimentally and the axial encapsulation length is increased significantly. The usage of anisotropic sheet material leads to a form fit and enhances the bond strength in draw-forged hybrid components. An alternative process route in which a pierced sheet is utilized to partially cover a specific section of a shaft was also developed. The process route was stabilized with a novel contoured counter holder to ensure high repeatability.
- 24 February 2022
- Published by Springer Nature in International Journal of Material Forming
- Vol. 15 (2) , 1-13
Open AccessExtending the potentials of draw-forging
Composite components combine the benefits of different materials, leading to improved product properties, enhanced resource- and energy efficiency and widening the product spectrum. Draw-forging is the unique combination of deep-drawing and cold forging, where a core material is encapsulated within a thin sheet metal blank. Previously, the basic draw-forging process only allowed covering of the shaft tip, and the covered length was limited by the maximum drawing ratio of the sheet. In this work, the different failure types, including tearing of the sheet, asymmetric encapsulation, and the development of a gap in the transition zone were investigated numerically and experimentally and the axial encapsulation length is increased significantly. The usage of anisotropic sheet material leads to a form fit and enhances the bond strength in draw-forged hybrid components. An alternative process route in which a pierced sheet is utilized to partially cover a specific section of a shaft was also developed. The process route was stabilized with a novel contoured counter holder to ensure high repeatability.
- Open Access
- 22 October 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 9 (4) , 1035-1048
Production and Subsequent Forming of Chip-Based Aluminium Sheets Without Remelting
Bent components and deep drawn cups are produced by direct usage of aluminium chips without melting following a new process chain: hot extrusion of aluminium chips to a cylindrical open profile, flattening, subsequent rolling and bending or deep drawing. The properties of the hot extruded chip-based AA6060 sheets are examined by tensile tests and microstructural investigations and the results are compared with those obtained from material extruded from conventional cast billets. The chip-based sheets were used to form components by bending or deep drawing. No significant differences between the bent components or deep-drawn cups made of chips and those from cast material are observed regarding their capability for further plastic forming operations. This makes the new process route a resource-efficient alternative for the production of aluminium sheet products.
- 22 October 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 9 (4) , 1035-1048
Open AccessProduction and Subsequent Forming of Chip-Based Aluminium Sheets Without Remelting
Bent components and deep drawn cups are produced by direct usage of aluminium chips without melting following a new process chain: hot extrusion of aluminium chips to a cylindrical open profile, flattening, subsequent rolling and bending or deep drawing. The properties of the hot extruded chip-based AA6060 sheets are examined by tensile tests and microstructural investigations and the results are compared with those obtained from material extruded from conventional cast billets. The chip-based sheets were used to form components by bending or deep drawing. No significant differences between the bent components or deep-drawn cups made of chips and those from cast material are observed regarding their capability for further plastic forming operations. This makes the new process route a resource-efficient alternative for the production of aluminium sheet products.
- 1 December 2019
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 274
Predicting weld-quality in direct hot extrusion of aluminium chips
- 1 December 2019
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 274
Predicting weld-quality in direct hot extrusion of aluminium chips
- 1 April 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 10, 217-225
Developments in composite extrusion of complex profiles for automotive applications
- 1 April 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 10, 217-225
Developments in composite extrusion of complex profiles for automotive applications