Le Hong Ky
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Le Hong Ky has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Ta Van Ranh
Vinh Long University of Technology Education
5 shared publicationsTran Vinh Hung
Phenikaa University
5 shared publications- Le Xuan Hung
Thai Nguyen University of Technology
3 shared publications - Luu Anh Tung
Faculty of Mechanical Engineering, Thai Nguyen University of Technology, 3/2 Street, Tich Luong Ward, Thai Nguyen City 24000, Vietnam
3 shared publications Nguyen Hoang Hiep
Vinh Long University of Technology Education
3 shared publications- Quoc-Tuan Nguyen
Academic Affairs, Thai Nguyen University, Tan Thinh ward, Thai Nguyen City 24118, Vietnam
3 shared publications
Latest Publications
- Open Access
- 1 April 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 16 (2) , 638-650
Dynamic analysis of a human-transporting robot climbing stairs
Robots used for transporting people on stairs face several limitations regarding tipping and safety hazards. Changes in the robot's center of gravity during stair climbing can generate tipping moments, leading to instability, tipping, and increased danger to users. This paper presents the modeling and analysis results of a tracked robot for transporting people on stairs, equipped with an anti-tipping mechanism based on center of gravity balance, combined with a vibration-damping mechanism mounted at the rear of the robot to enhance stability during stair climbing. Based on Newton-Euler's formulas, robot dynamics equations are established to describe the motion and analyze the robot's stability characteristics. Simulation and experimental results investigating the changes in center of gravity, velocity, tipping moment, and balancing moment of the robot during uphill and downhill movement were performed using MATLAB Simulink software. Simulation results indicate that the robot's center of gravity is adjusted and stabilized throughout both uphill and downhill movements. Practical experiments conducted on a fabricated robot model, capable of carrying a 100 kg load and moving up and down stairs with a 35-degree incline, demonstrated the feasibility and effectiveness of the proposed mechanical design. The results showed good agreement in kinematic trends between experimental and simulated data during the stair climbing, stair-on, and stair-step transition phases. This agreement between experimental and simulation results proved the correctness of the robot system and the constructed dynamic model. The research results provide a basis for developing control algorithms for robots that efficiently transport people up and down stairs in buildings.
- 1 April 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 16 (2) , 638-650
Open AccessDynamic analysis of a human-transporting robot climbing stairs
Robots used for transporting people on stairs face several limitations regarding tipping and safety hazards. Changes in the robot's center of gravity during stair climbing can generate tipping moments, leading to instability, tipping, and increased danger to users. This paper presents the modeling and analysis results of a tracked robot for transporting people on stairs, equipped with an anti-tipping mechanism based on center of gravity balance, combined with a vibration-damping mechanism mounted at the rear of the robot to enhance stability during stair climbing. Based on Newton-Euler's formulas, robot dynamics equations are established to describe the motion and analyze the robot's stability characteristics. Simulation and experimental results investigating the changes in center of gravity, velocity, tipping moment, and balancing moment of the robot during uphill and downhill movement were performed using MATLAB Simulink software. Simulation results indicate that the robot's center of gravity is adjusted and stabilized throughout both uphill and downhill movements. Practical experiments conducted on a fabricated robot model, capable of carrying a 100 kg load and moving up and down stairs with a 35-degree incline, demonstrated the feasibility and effectiveness of the proposed mechanical design. The results showed good agreement in kinematic trends between experimental and simulated data during the stair climbing, stair-on, and stair-step transition phases. This agreement between experimental and simulation results proved the correctness of the robot system and the constructed dynamic model. The research results provide a basis for developing control algorithms for robots that efficiently transport people up and down stairs in buildings.
- 26 March 2026
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 20 (6) , 3053-3063
Entropy-based multi-criteria decision framework for plasma nitriding of hypoid gears
- 26 March 2026
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 20 (6) , 3053-3063
Entropy-based multi-criteria decision framework for plasma nitriding of hypoid gears
- 1 November 2025
- Published by Springer Nature
- p. 523-530
Shaft Concentricity Calibration and Vibration Evaluation of VLUTE A01 Rotary Friction Welding
- 1 November 2025
- Published by Springer Nature
- p. 523-530
Shaft Concentricity Calibration and Vibration Evaluation of VLUTE A01 Rotary Friction Welding
- 1 November 2025
- Published by Springer Nature
- p. 208-216
Building a Balancing Control Algorithm for Human Transport Robots When Moving up and Down Stairs
- 1 November 2025
- Published by Springer Nature
- p. 208-216
Building a Balancing Control Algorithm for Human Transport Robots When Moving up and Down Stairs
- 5 October 2025
- Published by Springer Nature
- p. 75-83
A Sliding Mode Control Algorithm Applied to Balance the User When the Robot Moves on the Staircase of Building
- 5 October 2025
- Published by Springer Nature
- p. 75-83
A Sliding Mode Control Algorithm Applied to Balance the User When the Robot Moves on the Staircase of Building
- Open Access
- 4 June 2025
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 15 (3) , 23756-23766
Building an Anti-Tip System for Robots Transporting People Up and Down the Stairs
This paper presents an anti-roll control model for a human transport robot that can go up and down stairs with different slopes. The anti-roll control system is implemented by the process of controlling the robot's center of gravity and the adaptive mechanism. The anti-roll equation when moving up and down stairs is proposed with a balance system by a linear actuator to help control the balance and anti-roll according to the slope of the stairs. The phenomenon of oscillation and overturning towards the moving direction at the last step of the stairs is also considered and analyzed, and a control equation is built to limit this phenomenon. The suitability of the dynamic equations is verified through simulation results on Matlab Simulink software. The experimental model was constructed and tested in real conditions with a slope of 35º. The experimental results of the human transport robot show that the robot is balanced and stable when moving up and down stairs. This shows the effectiveness of the anti-roll model for the crawler human transport robot.
- 4 June 2025
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 15 (3) , 23756-23766
Open AccessBuilding an Anti-Tip System for Robots Transporting People Up and Down the Stairs
This paper presents an anti-roll control model for a human transport robot that can go up and down stairs with different slopes. The anti-roll control system is implemented by the process of controlling the robot's center of gravity and the adaptive mechanism. The anti-roll equation when moving up and down stairs is proposed with a balance system by a linear actuator to help control the balance and anti-roll according to the slope of the stairs. The phenomenon of oscillation and overturning towards the moving direction at the last step of the stairs is also considered and analyzed, and a control equation is built to limit this phenomenon. The suitability of the dynamic equations is verified through simulation results on Matlab Simulink software. The experimental model was constructed and tested in real conditions with a slope of 35º. The experimental results of the human transport robot show that the robot is balanced and stable when moving up and down stairs. This shows the effectiveness of the anti-roll model for the crawler human transport robot.
- Open Access
- 17 October 2024
- Published by IOS Press
- p. 80-86
Evaluation of Technical Specifications of Rotary Friction Welding Machine Improved from Lathe
Nowadays, rotary friction welding (RFW) is increasingly used because of its outstanding advantages compared to traditional fusion welding methods such as plastic melting temperature below the melting temperature, good mechanical properties and durability of the joint material, high productivity, and being environmentally friendly. Operating parameters are set to suit each type of material, and the operating process is controlled flexibly and easily. Therefore, it is possible to weld a variety of sizes and materials, so rotary friction welding is widely used in the fields of aerospace, automobiles, machinery parts, and automation industry. The purpose of this paper is to study friction welding on lathes instead of specialized welding machines by improving the Yamazaki CT800 universal lathe into a rotary friction welding machine. The improved main mechanisms include the non-rotating chuck mounting mechanism, pressing pressure, rotation speed brake, parameter setting and welding process control. Results of testing rotation speed, vibration, shaft misalignment and weld durability for C45 steel show that the improved equipment meets the set requirements.
- 17 October 2024
- Published by IOS Press
- p. 80-86
Open AccessEvaluation of Technical Specifications of Rotary Friction Welding Machine Improved from Lathe
Nowadays, rotary friction welding (RFW) is increasingly used because of its outstanding advantages compared to traditional fusion welding methods such as plastic melting temperature below the melting temperature, good mechanical properties and durability of the joint material, high productivity, and being environmentally friendly. Operating parameters are set to suit each type of material, and the operating process is controlled flexibly and easily. Therefore, it is possible to weld a variety of sizes and materials, so rotary friction welding is widely used in the fields of aerospace, automobiles, machinery parts, and automation industry. The purpose of this paper is to study friction welding on lathes instead of specialized welding machines by improving the Yamazaki CT800 universal lathe into a rotary friction welding machine. The improved main mechanisms include the non-rotating chuck mounting mechanism, pressing pressure, rotation speed brake, parameter setting and welding process control. Results of testing rotation speed, vibration, shaft misalignment and weld durability for C45 steel show that the improved equipment meets the set requirements.
- 25 August 2024
- Published by Springer Nature
- p. 132-141
A Study on the Influence of Plasma Nitriding Technology Parameters on the Working Surface Roughness of Hypoid Gears
- 25 August 2024
- Published by Springer Nature
- p. 132-141
A Study on the Influence of Plasma Nitriding Technology Parameters on the Working Surface Roughness of Hypoid Gears
- 31 May 2024
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 12 (S1) , 793-802
Effect of Plasma Nitriding Technology Parameters on Working Surface Quality Gears made of SAE 5120 Steel
- 31 May 2024
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 12 (S1) , 793-802
Effect of Plasma Nitriding Technology Parameters on Working Surface Quality Gears made of SAE 5120 Steel
- Open Access
- 2 April 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (2) , 13643-13647
The Influence of Plasma Nitriding Technology Parameters on the Hardness of 18XГT Steel Parts
This article presents the results of the research on the influence of plasma nitriding technology parameters on the working surface hardness of machine parts made of previously hardened 18XГT steel. A total of 27 experiments were conducted on the H4580 Eltrolab instrument. Minitab software was used to process the experimental results. The regression function set up with visual charts was utilized as the basis for analysis of the influence of temperature, time, and gas permeation concentration on the working surface hardness. Analysis of variance (ANOVA) showed that all the nitriding technology parameters influenced the regression function. The permeation temperature TL had the greatest influence on hardness, while the permeation time h and the gas permeation concentration G1 had less influence. When the double interaction between the parameters was considered, it was shown that these pairs also had a large influence on the surface hardness, but at different levels.
- 2 April 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (2) , 13643-13647
Open AccessThe Influence of Plasma Nitriding Technology Parameters on the Hardness of 18XГT Steel Parts
This article presents the results of the research on the influence of plasma nitriding technology parameters on the working surface hardness of machine parts made of previously hardened 18XГT steel. A total of 27 experiments were conducted on the H4580 Eltrolab instrument. Minitab software was used to process the experimental results. The regression function set up with visual charts was utilized as the basis for analysis of the influence of temperature, time, and gas permeation concentration on the working surface hardness. Analysis of variance (ANOVA) showed that all the nitriding technology parameters influenced the regression function. The permeation temperature TL had the greatest influence on hardness, while the permeation time h and the gas permeation concentration G1 had less influence. When the double interaction between the parameters was considered, it was shown that these pairs also had a large influence on the surface hardness, but at different levels.