David B. Brown
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
David B. Brown has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Satish Kumar
G. W. Woodruff School of Mechanical Engineering , Georgia Institute of Technology , Atlanta , Georgia 30332 , United States
2 shared publicationsThomas L. Bougher
G. W. Woodruff School of Mechanical Engineering Georgia Institute of Technology Atlanta GA 30332 USA
2 shared publicationsBaratunde A. Cola
G. W. Woodruff School of Mechanical Engineering Georgia Institute of Technology Atlanta GA 30332 USA
1 shared publication- Baratunde A. Cola
George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology 1 , Atlanta, Georgia 30332, USA
1 shared publication David B. Geohegan
Center for Nanophase Materials Sciences , Oak Ridge National Laboratory , Oak Ridge , Tennessee 37831 , United States
1 shared publicationIndronil Ghosh
University of California
1 shared publication
Latest Publications
- 1 October 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- Vol. 39 (4) , 788-803
Integrated Multimode, Multiphase Cooling of High-Speed Leading Edges
Hypersonic air vehicles are increasingly relevant to planned commercial and defense applications. These vehicles are subjected to extreme temperatures and stresses that can severely limit functional performance. As a result, aerodynamic design requirements must be balanced with thermal management considerations for sustained flight at hypersonic speeds, with specific attention devoted to the leading edge because of extreme local heat fluxes in this region. Thermionic cooling has been proposed as a thermal management technique for hypersonic leading edges, but heat conduction into the surface has been neglected in such models. Here, a multimode cooling model is reported that estimates surface temperatures around the stagnation point, the location of maximum heat flux near the leading edge. The leading edge is modeled using a heat-balance integral formulation of one-dimensional heat conduction with phase change and combined radiative, thermionic, and evaporative heat fluxes at the surface. A well-known, low-work-function emitter material, lanthanum hexaboride, is analyzed, and the wall temperature is predicted to reach just below the melting point of the emitter material at Mach 5 and 10 when the emission current is calculated by the Richardson–Dushman equation. Conduction into the surface is a significant percentage of the total cooling at short times and low Mach numbers, while additional cooling modes begin to dominate at longer times. However, when space-charge effects are considered, the wall temperature reaches the melting point of the emitter at Mach 10 and 15, and the molten material is quickly removed by the high enthalpy flow. Our model predicts the emission current decreases significantly but approaches the Richardson current at Mach 15 if the surface is negatively biased. The results presented here can impact material selection and provide inputs for higher-fidelity models and experiments, leading to a more robust thermal design of hypersonic vehicles.
- 1 October 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- Vol. 39 (4) , 788-803
Integrated Multimode, Multiphase Cooling of High-Speed Leading Edges
Hypersonic air vehicles are increasingly relevant to planned commercial and defense applications. These vehicles are subjected to extreme temperatures and stresses that can severely limit functional performance. As a result, aerodynamic design requirements must be balanced with thermal management considerations for sustained flight at hypersonic speeds, with specific attention devoted to the leading edge because of extreme local heat fluxes in this region. Thermionic cooling has been proposed as a thermal management technique for hypersonic leading edges, but heat conduction into the surface has been neglected in such models. Here, a multimode cooling model is reported that estimates surface temperatures around the stagnation point, the location of maximum heat flux near the leading edge. The leading edge is modeled using a heat-balance integral formulation of one-dimensional heat conduction with phase change and combined radiative, thermionic, and evaporative heat fluxes at the surface. A well-known, low-work-function emitter material, lanthanum hexaboride, is analyzed, and the wall temperature is predicted to reach just below the melting point of the emitter material at Mach 5 and 10 when the emission current is calculated by the Richardson–Dushman equation. Conduction into the surface is a significant percentage of the total cooling at short times and low Mach numbers, while additional cooling modes begin to dominate at longer times. However, when space-charge effects are considered, the wall temperature reaches the melting point of the emitter at Mach 10 and 15, and the molten material is quickly removed by the high enthalpy flow. Our model predicts the emission current decreases significantly but approaches the Richardson current at Mach 15 if the surface is negatively biased. The results presented here can impact material selection and provide inputs for higher-fidelity models and experiments, leading to a more robust thermal design of hypersonic vehicles.
- 25 September 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (23)
Thermal Boundary Conductance and Phonon Transmission in Hexagonal Boron Nitride/Graphene Heterostructures
Two‐dimensional (2D) materials such as graphene and hexagonal boron nitride (h‐BN) have attracted interest as a conductor/insulator pair in next‐generation devices because of their unique physical properties; however, the thermal transport at the interfaces must be understood to accurately predict the performance of heterostructures composed of these materials. Time‐domain thermoreflectance (TDTR) is used to estimate the thermal boundary conductance (TBC) at the interface of h‐BN and graphene to be 34.5 (+11.6/−7.4) MW m−2 K−1. The advantage of TDTR is that it does not need to create a large temperature gradient at the interface of heterostructures, but it has not yet been used for h‐BN/graphene interface. Phonon transmission and TBC at the h‐BN/graphene interface are predicted by two different formulations of the diffuse mismatch model (DMM) for anisotropic materials. The analysis of phonon transmission and temperature dependence of TBC establishes the flexural branch in theab‐plane, and thec‐plane longitudinal acoustic branch of graphene and h‐BN are the dominant contributors when implementing both the DMM models. The methodology developed herein can be used to analyze heterostructures of other 2D materials.
- 25 September 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (23)
Thermal Boundary Conductance and Phonon Transmission in Hexagonal Boron Nitride/Graphene Heterostructures
Two‐dimensional (2D) materials such as graphene and hexagonal boron nitride (h‐BN) have attracted interest as a conductor/insulator pair in next‐generation devices because of their unique physical properties; however, the thermal transport at the interfaces must be understood to accurately predict the performance of heterostructures composed of these materials. Time‐domain thermoreflectance (TDTR) is used to estimate the thermal boundary conductance (TBC) at the interface of h‐BN and graphene to be 34.5 (+11.6/−7.4) MW m−2 K−1. The advantage of TDTR is that it does not need to create a large temperature gradient at the interface of heterostructures, but it has not yet been used for h‐BN/graphene interface. Phonon transmission and TBC at the h‐BN/graphene interface are predicted by two different formulations of the diffuse mismatch model (DMM) for anisotropic materials. The analysis of phonon transmission and temperature dependence of TBC establishes the flexural branch in theab‐plane, and thec‐plane longitudinal acoustic branch of graphene and h‐BN are the dominant contributors when implementing both the DMM models. The methodology developed herein can be used to analyze heterostructures of other 2D materials.
- 21 March 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (15) , 14418-14426
Spatial Mapping of Thermal Boundary Conductance at Metal–Molybdenum Diselenide Interfaces
Improving the thermal transport across interfaces is a necessary consideration for micro- and nano-electronic devices and necessitates accurate measurement of the thermal boundary conductance (TBC) and understanding of transport mechanisms. Two-dimensional transition metal dichalcogenides (TMDs) have been studied extensively for their electrical properties, including the metal-TMD electrical contact resistance, but the thermal properties of these interfaces are significantly less explored irrespective of their high importance in their electronic devices. We isolate individual islands of MoSe2 grown by chemical vapor deposition using photolithography and correlate the 2D variation of TBC with optical microscope images of the MoSe2 islands. We measure the 2D spatial variation of the TBC at metal-MoSe2-SiO2 interfaces using a modified time-domain thermoreflectance (TDTR) technique which requires much less time than full TDTR scans. The thermoreflectance signal at a single probe delay time is compared with a correlation curve which enables us to estimate the change in the signal with respect to the TBC at metal-MoSe2-SiO2 interface as opposed to recording the decay of the thermoreflectance signal over delay times of several nanoseconds. The results show higher TBC across Ti-MoSe2-SiO2 interface compared to Al-MoSe2-SiO2. An image clustering method is developed to differentiate the TBC for different number of MoSe2 layers, which reveals the TBC in single-layer regions is higher than bilayer. We perform traditional TDTR measurements over a range of delay times and verify TBC is higher at Ti-MoSe2-SiO2 interface compared to Al-MoSe2-SiO2 highlighting the importance of the choice of metal to heat dissipation at electrical contacts in TMD devices.
- 21 March 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (15) , 14418-14426
Spatial Mapping of Thermal Boundary Conductance at Metal–Molybdenum Diselenide Interfaces
Improving the thermal transport across interfaces is a necessary consideration for micro- and nano-electronic devices and necessitates accurate measurement of the thermal boundary conductance (TBC) and understanding of transport mechanisms. Two-dimensional transition metal dichalcogenides (TMDs) have been studied extensively for their electrical properties, including the metal-TMD electrical contact resistance, but the thermal properties of these interfaces are significantly less explored irrespective of their high importance in their electronic devices. We isolate individual islands of MoSe2 grown by chemical vapor deposition using photolithography and correlate the 2D variation of TBC with optical microscope images of the MoSe2 islands. We measure the 2D spatial variation of the TBC at metal-MoSe2-SiO2 interfaces using a modified time-domain thermoreflectance (TDTR) technique which requires much less time than full TDTR scans. The thermoreflectance signal at a single probe delay time is compared with a correlation curve which enables us to estimate the change in the signal with respect to the TBC at metal-MoSe2-SiO2 interface as opposed to recording the decay of the thermoreflectance signal over delay times of several nanoseconds. The results show higher TBC across Ti-MoSe2-SiO2 interface compared to Al-MoSe2-SiO2. An image clustering method is developed to differentiate the TBC for different number of MoSe2 layers, which reveals the TBC in single-layer regions is higher than bilayer. We perform traditional TDTR measurements over a range of delay times and verify TBC is higher at Ti-MoSe2-SiO2 interface compared to Al-MoSe2-SiO2 highlighting the importance of the choice of metal to heat dissipation at electrical contacts in TMD devices.
- 1 December 1990
- Published by Elsevier in Experimental Cell Research
- Vol. 191 (2) , 328-331
Analysis of cis-acting promoter elements using microinjected synthetic oligonucleotides
- 1 December 1990
- Published by Elsevier in Experimental Cell Research
- Vol. 191 (2) , 328-331
Analysis of cis-acting promoter elements using microinjected synthetic oligonucleotides