Giulio Boccardo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Giulio Boccardo has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Federico Millo
8 shared publications- Andrea Piano
Energy Department, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy
6 shared publications Stefano Manelli
Kohler Engines
5 shared publicationsLuigi Arnone
Kohler Engines
4 shared publicationsAndrea Marinoni
Kohler Engines
2 shared publicationsFrancesco Concetto Pesce
2 shared publications
Latest Publications
- 1 November 2019
- Published by Elsevier in Applied Thermal Engineering
- Vol. 162
Numerical and experimental investigation of a piston thermal barrier coating for an automotive diesel engine application
- 1 November 2019
- Published by Elsevier in Applied Thermal Engineering
- Vol. 162
Numerical and experimental investigation of a piston thermal barrier coating for an automotive diesel engine application
- 9 September 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
The Effect of Post Injection Coupled with Extremely High Injection Pressure on Combustion Process and Emission Formation in an Off-Road Diesel Engine: A Numerical and Experimental Investigation
In this paper, a numerical and experimental assessment of post injection potential for soot emissions mitigation in an off-road diesel engine is presented, with the aim of supporting hardware selection and engine calibration processes. As a case study, a prototype off-road 3.4 liters 4-cylinder diesel engine developed by Kohler Engines was selected. In order to explore the possibility to comply with Stage V emission standards without a dedicated aftertreatment for NOx, the engine was equipped with a low pressure cooled Exhaust Gas Recirculation (EGR), allowing high EGR rates (above 30%) even at high load. To enable the exploitation of such high EGR rates with acceptable soot penalties, a two-stage turbocharger and an extremely high-pressure fuel injection system (up to 3000 bar) were adopted. Moreover, post injections events were also exploited to further mitigate soot emissions with acceptable Brake Specific Fuel Consumption (BSFC) penalties. Since the selection of the post injection calibration parameters (such as injected quantity and dwell time) is crucial to maximizing its efficacy, a 3D-CFD engine model was built and calibrated to evaluate its effects on soot emissions and fuel consumption. With this aim, different post injection strategies at rated speed / 50% load operating conditions were analyzed, highlighting the potential to achieve impressive soot mitigations (up to 50%) with negligible (< 1%) BSFC penalties. The numerical analysis also allowed a better understanding of the phenomena leading to soot emissions reduction, setting guidelines for the subsequent calibration experimental activity, which confirmed the simulation results and could be successfully extended to the whole engine operating map.
- 9 September 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
The Effect of Post Injection Coupled with Extremely High Injection Pressure on Combustion Process and Emission Formation in an Off-Road Diesel Engine: A Numerical and Experimental Investigation
In this paper, a numerical and experimental assessment of post injection potential for soot emissions mitigation in an off-road diesel engine is presented, with the aim of supporting hardware selection and engine calibration processes. As a case study, a prototype off-road 3.4 liters 4-cylinder diesel engine developed by Kohler Engines was selected. In order to explore the possibility to comply with Stage V emission standards without a dedicated aftertreatment for NOx, the engine was equipped with a low pressure cooled Exhaust Gas Recirculation (EGR), allowing high EGR rates (above 30%) even at high load. To enable the exploitation of such high EGR rates with acceptable soot penalties, a two-stage turbocharger and an extremely high-pressure fuel injection system (up to 3000 bar) were adopted. Moreover, post injections events were also exploited to further mitigate soot emissions with acceptable Brake Specific Fuel Consumption (BSFC) penalties. Since the selection of the post injection calibration parameters (such as injected quantity and dwell time) is crucial to maximizing its efficacy, a 3D-CFD engine model was built and calibrated to evaluate its effects on soot emissions and fuel consumption. With this aim, different post injection strategies at rated speed / 50% load operating conditions were analyzed, highlighting the potential to achieve impressive soot mitigations (up to 50%) with negligible (< 1%) BSFC penalties. The numerical analysis also allowed a better understanding of the phenomena leading to soot emissions reduction, setting guidelines for the subsequent calibration experimental activity, which confirmed the simulation results and could be successfully extended to the whole engine operating map.
Experimental investigation on a 3000 bar fuel injection system for a SCR-free non-road diesel engine
- Open Access
Impact of Different Driving Cycles and Operating Conditions on CO2 Emissions and Energy Management Strategies of a Euro-6 Hybrid Electric Vehicle
Although Hybrid Electric Vehicles (HEVs) represent one of the key technologies to reduce CO2 emissions, their effective potential in real world driving conditions strongly depends on the performance of their Energy Management System (EMS) and on its capability to maximize the efficiency of the powertrain in real life as well as during Type Approval (TA) tests. Attempting to close the gap between TA and real world CO2 emissions, the European Commission has decided to introduce from September 2017 the Worldwide Harmonized Light duty Test Procedure (WLTP), replacing the previous procedure based on the New European Driving Cycle (NEDC). The aim of this work is the analysis of the impact of different driving cycles and operating conditions on CO2 emissions and on energy management strategies of a Euro-6 HEV through the limited number of information available from the chassis dyno tests. The vehicle was tested considering different initial battery State of Charge (SOC), ranging from 40% to 65%, and engine coolant temperatures, from −7 °C to 70 °C. The change of test conditions from NEDC to WLTP was shown to lead to a significant reduction of the electric drive and to about a 30% increase of CO2 emissions. However, since the specific energy demand of WLTP is about 50% higher than that of NEDC, these results demonstrate that the EMS strategies of the tested vehicle can achieve, in test conditions closer to real life, even higher efficiency levels than those that are currently evaluated on the NEDC, and prove the effectiveness of HEV technology to reduce CO2 emissions.
Open AccessImpact of Different Driving Cycles and Operating Conditions on CO2 Emissions and Energy Management Strategies of a Euro-6 Hybrid Electric Vehicle
Although Hybrid Electric Vehicles (HEVs) represent one of the key technologies to reduce CO2 emissions, their effective potential in real world driving conditions strongly depends on the performance of their Energy Management System (EMS) and on its capability to maximize the efficiency of the powertrain in real life as well as during Type Approval (TA) tests. Attempting to close the gap between TA and real world CO2 emissions, the European Commission has decided to introduce from September 2017 the Worldwide Harmonized Light duty Test Procedure (WLTP), replacing the previous procedure based on the New European Driving Cycle (NEDC). The aim of this work is the analysis of the impact of different driving cycles and operating conditions on CO2 emissions and on energy management strategies of a Euro-6 HEV through the limited number of information available from the chassis dyno tests. The vehicle was tested considering different initial battery State of Charge (SOC), ranging from 40% to 65%, and engine coolant temperatures, from −7 °C to 70 °C. The change of test conditions from NEDC to WLTP was shown to lead to a significant reduction of the electric drive and to about a 30% increase of CO2 emissions. However, since the specific energy demand of WLTP is about 50% higher than that of NEDC, these results demonstrate that the EMS strategies of the tested vehicle can achieve, in test conditions closer to real life, even higher efficiency levels than those that are currently evaluated on the NEDC, and prove the effectiveness of HEV technology to reduce CO2 emissions.
- 19 September 2017
- Published by Springer Nature
- p. 274-291
Investigation of a ‘SCR-free’ system to meet the Stage IV and beyond emissions limits
- 19 September 2017
- Published by Springer Nature
- p. 274-291
Investigation of a ‘SCR-free’ system to meet the Stage IV and beyond emissions limits
- 4 September 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Numerical Simulation of the Combustion Process of a High EGR, High Injection Pressure, Heavy Duty Diesel Engine
To comply with Stage IV emission standard for off-road engines, Kohler Engines has developed the 100kW rated KDI 3.4 liters diesel engine, equipped with DOC and SCR. Based on this engine, a research project in collaboration between Kohler Engines, Ricardo, Denso and Politecnico di Torino was carried out to exploit the potential of new technologies to meet the Stage IV and beyond emission standards.The prototype engine was equipped with a low pressure cooled EGR system, two stage turbocharger, high pressure fuel injection system capable of very high injection pressure and DOC+DPF aftertreatment system. Since the Stage IV emission standard sets a 0.4 g/kWh NOx limit for the steady state test cycle (NRSC), that includes full load operating conditions, the engine must be operated with very high EGR rates (above 30%) at very high load. As a consequence, the low air to fuel ratio and the risk of high soot emissions must be handled by means of high fuel injection pressure and proper injection patterns.In this context, the DIPulse multizone predictive combustion model developed by Gamma Technologies was extensively employed to support the engine calibration and the hardware selection processes. After populating the injection rate map starting from a limited set of measurements, the model was then calibrated to simulate the combustion process with extremely high injection pressures and EGR rates, achieving a very good correlation with the experimental data in terms of burn rates, engine performance parameters and NOx emissions. In this way a kind of “virtual test rig” was obtained, on which the effects of different injection patterns and hardware components could be analyzed, thus significantly shortening the hardware selection and calibration activities on the test bench to achieve the project targets.
- 4 September 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Numerical Simulation of the Combustion Process of a High EGR, High Injection Pressure, Heavy Duty Diesel Engine
To comply with Stage IV emission standard for off-road engines, Kohler Engines has developed the 100kW rated KDI 3.4 liters diesel engine, equipped with DOC and SCR. Based on this engine, a research project in collaboration between Kohler Engines, Ricardo, Denso and Politecnico di Torino was carried out to exploit the potential of new technologies to meet the Stage IV and beyond emission standards.The prototype engine was equipped with a low pressure cooled EGR system, two stage turbocharger, high pressure fuel injection system capable of very high injection pressure and DOC+DPF aftertreatment system. Since the Stage IV emission standard sets a 0.4 g/kWh NOx limit for the steady state test cycle (NRSC), that includes full load operating conditions, the engine must be operated with very high EGR rates (above 30%) at very high load. As a consequence, the low air to fuel ratio and the risk of high soot emissions must be handled by means of high fuel injection pressure and proper injection patterns.In this context, the DIPulse multizone predictive combustion model developed by Gamma Technologies was extensively employed to support the engine calibration and the hardware selection processes. After populating the injection rate map starting from a limited set of measurements, the model was then calibrated to simulate the combustion process with extremely high injection pressures and EGR rates, achieving a very good correlation with the experimental data in terms of burn rates, engine performance parameters and NOx emissions. In this way a kind of “virtual test rig” was obtained, on which the effects of different injection patterns and hardware components could be analyzed, thus significantly shortening the hardware selection and calibration activities on the test bench to achieve the project targets.
- 4 September 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
A Fully Physical Correlation for Low Pressure EGR Control Linearization
Nowadays stringent emission regulations are pushing towards new air management strategies like LP-EGR and HP/LP mix both for passenger car and heavy duty applications, increasing the engine control complexity.Within a project in collaboration between Kohler Engines EMEA, Politecnico di Torino, Ricardo and Denso to exploit the potential of EGR-Only technologies, a 3.4 liters KDI 3404 was equipped with a two stage turbocharging system, an extremely high pressure FIS and a low pressure EGR system. The LP-EGR system works in a closed loop control with an intake oxygen sensor actuating two valves: an EGR valve placed downstream of the EGR cooler that regulates the flow area of the bypass between the exhaust line and the intake line, and an exhaust flap to generate enough backpressure to recirculate the needed EGR rate to cut the NOx emission without a specific aftertreatment device.In this paper it will be demonstrated how, using a 1D-CFD code to characterize the flow in the exhaust line and in the EGR pathway, together with simple physical correlations, it is possible to define the opening laws of the two valves in order to both obtain a linear response of the EGR control and minimize the fuel consumption increase due to the backpressure valve.
- 4 September 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
A Fully Physical Correlation for Low Pressure EGR Control Linearization
Nowadays stringent emission regulations are pushing towards new air management strategies like LP-EGR and HP/LP mix both for passenger car and heavy duty applications, increasing the engine control complexity.Within a project in collaboration between Kohler Engines EMEA, Politecnico di Torino, Ricardo and Denso to exploit the potential of EGR-Only technologies, a 3.4 liters KDI 3404 was equipped with a two stage turbocharging system, an extremely high pressure FIS and a low pressure EGR system. The LP-EGR system works in a closed loop control with an intake oxygen sensor actuating two valves: an EGR valve placed downstream of the EGR cooler that regulates the flow area of the bypass between the exhaust line and the intake line, and an exhaust flap to generate enough backpressure to recirculate the needed EGR rate to cut the NOx emission without a specific aftertreatment device.In this paper it will be demonstrated how, using a 1D-CFD code to characterize the flow in the exhaust line and in the EGR pathway, together with simple physical correlations, it is possible to define the opening laws of the two valves in order to both obtain a linear response of the EGR control and minimize the fuel consumption increase due to the backpressure valve.
- 4 September 2017
- Published by SAE International in SAE International Journal of Engines
- Vol. 10 (4) , 2129-2140
Experimental and Numerical Assessment of Multi-Event Injection Strategies in a Solenoid Common-Rail Injector
Nowadays, injection rate shaping and multi-pilot events can help to improve fuel efficiency, combustion noise and pollutant emissions in diesel engine, providing high flexibility in the shape of the injection that allows combustion process control. Different strategies can be used in order to obtain the required flexibility in the rate, such as very close pilot injections with almost zero Dwell Time or boot shaped injections with optional pilot injections. Modern Common-Rail Fuel Injection Systems (FIS) should be able to provide these innovative patterns to control the combustion phases intensity for optimal tradeoff between fuel consumption and emission levels.In this work, a 1D-CFD model in GT-SUITE of a solenoid ballistic Common-Rail injector was firstly refined respect to the previous work [1] and then it was validated against an extensive experimental dataset of single injections, standard double pilot and multi-pilot injection patterns (up to 4 pilot events) with almost zero dwell time between two consecutive injection events. The experimental hydraulic test data used to validate the one-dimensional model were obtained by means of the UniPG Injection Analyzer based on the Zeuch’s method.The comparison between the experimental and simulated volumetric injection rates showed a more than satisfactory accuracy of the model in predicting the actual behavior of the ballistic injector for all the injection patterns tested, even for relatively complex injector command strategies, characterized by reduced Dwell Time values between consecutive injection events.
- 4 September 2017
- Published by SAE International in SAE International Journal of Engines
- Vol. 10 (4) , 2129-2140
Experimental and Numerical Assessment of Multi-Event Injection Strategies in a Solenoid Common-Rail Injector
Nowadays, injection rate shaping and multi-pilot events can help to improve fuel efficiency, combustion noise and pollutant emissions in diesel engine, providing high flexibility in the shape of the injection that allows combustion process control. Different strategies can be used in order to obtain the required flexibility in the rate, such as very close pilot injections with almost zero Dwell Time or boot shaped injections with optional pilot injections. Modern Common-Rail Fuel Injection Systems (FIS) should be able to provide these innovative patterns to control the combustion phases intensity for optimal tradeoff between fuel consumption and emission levels.In this work, a 1D-CFD model in GT-SUITE of a solenoid ballistic Common-Rail injector was firstly refined respect to the previous work [1] and then it was validated against an extensive experimental dataset of single injections, standard double pilot and multi-pilot injection patterns (up to 4 pilot events) with almost zero dwell time between two consecutive injection events. The experimental hydraulic test data used to validate the one-dimensional model were obtained by means of the UniPG Injection Analyzer based on the Zeuch’s method.The comparison between the experimental and simulated volumetric injection rates showed a more than satisfactory accuracy of the model in predicting the actual behavior of the ballistic injector for all the injection patterns tested, even for relatively complex injector command strategies, characterized by reduced Dwell Time values between consecutive injection events.
- 5 April 2016
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Assessment of the Predictive Capabilities of a Combustion Model for a Modern Common Rail Automotive Diesel Engine
The predictive capabilities of an innovative multizone combustion model DIPulse, developed by Gamma Technologies, were assessed in this work for a last generation common rail automotive diesel engine.A detailed validation process, based on an extensive experimental data set, was carried out concerning the predicted heat release rate, the in-cylinder pressure trace, as well as NOx and soot emissions for several operating points including both part load and full load points.After a preliminary calibration of the model, the combustion model parameters were then optimized through a Latin Hypercube Design of Experiment (DoE), with the aim of minimizing the RMS error between the predicted and experimental burn rate of several engine operating points, thus achieving a satisfactory agreement between simulation and experimental engine combustion and emissions parameters.
- 5 April 2016
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Assessment of the Predictive Capabilities of a Combustion Model for a Modern Common Rail Automotive Diesel Engine
The predictive capabilities of an innovative multizone combustion model DIPulse, developed by Gamma Technologies, were assessed in this work for a last generation common rail automotive diesel engine.A detailed validation process, based on an extensive experimental data set, was carried out concerning the predicted heat release rate, the in-cylinder pressure trace, as well as NOx and soot emissions for several operating points including both part load and full load points.After a preliminary calibration of the model, the combustion model parameters were then optimized through a Latin Hypercube Design of Experiment (DoE), with the aim of minimizing the RMS error between the predicted and experimental burn rate of several engine operating points, thus achieving a satisfactory agreement between simulation and experimental engine combustion and emissions parameters.