Jing-Yu Liang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jing-Yu Liang has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Dai-Soo Lee
Research Institute of Future Energy, Chonbuk National University, 567 Baekje-daero, Deokjini-gu, Jeonju 54896, Korea
3 shared publications - Se-Ra Shin
Department of Semiconductor and Chemical Engineering, Chonbuk National University, 567 Baekje-daero, Deokjini-gu, Jeonju 54896, Korea
3 shared publications - Soo-Hyoung Lee
School of Semiconductor and Chemical Engineering, Jeonbuk National University, 567 Baekje-daero, Deokjin-gu, Jeonju-si, Jeollabuk-do 54896, Republic of Korea
2 shared publications - Gwang-Seok Song
Industrial Biotechnology Program, Chemical R&D Center, Samyang Corporation, Daedeok-daero 730, Yuseong-gu, Daejeon 34055, Korea
1 shared publication - Hoon Ryu
Industrial Biotechnology Program, Chemical R&D Center, Samyang Corporation, Daedeok-daero 730, Yuseong-gu, Daejeon 34055, Korea
1 shared publication
Latest Publications
- Open Access
Self-Healing and Mechanical Properties of Thermoplastic Polyurethane/Eugenol-Based Phenoxy Resin Blends via Exchange Reactions
The possibility of exchange reactions and thermal self-healing in blends of thermoplastic polyurethane (TPU) and phenoxy resin was investigated herein. The analyses were based on characterization obtained via differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), and tensile test. A new phenoxy resin was synthesized from eugenol, and blends with different types of TPU were prepared to investigate the exchange reaction, thermal self-healing, and mechanical properties. The influence of phenoxy resin content on the mechanical behavior and healing efficiency was studied. Improvement of storage modulus owing to the increase of phenoxy resin content was observed. Results suggest that the exchange reaction between phenoxy- and ester-type TPU occurred during thermal treatment. However, little exchange occurred between phenoxy resin and ether-type TPU. Specifically, only ester-type TPU exhibited a significant exchange reaction in the phenoxy resin blend. Furthermore, in the presence of a catalyst (e.g., zinc acetate), the exchange reaction readily occurred, and the healing efficiency improved by the addition of the catalyst and increase in the phenoxy content.
Open AccessSelf-Healing and Mechanical Properties of Thermoplastic Polyurethane/Eugenol-Based Phenoxy Resin Blends via Exchange Reactions
The possibility of exchange reactions and thermal self-healing in blends of thermoplastic polyurethane (TPU) and phenoxy resin was investigated herein. The analyses were based on characterization obtained via differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), and tensile test. A new phenoxy resin was synthesized from eugenol, and blends with different types of TPU were prepared to investigate the exchange reaction, thermal self-healing, and mechanical properties. The influence of phenoxy resin content on the mechanical behavior and healing efficiency was studied. Improvement of storage modulus owing to the increase of phenoxy resin content was observed. Results suggest that the exchange reaction between phenoxy- and ester-type TPU occurred during thermal treatment. However, little exchange occurred between phenoxy resin and ether-type TPU. Specifically, only ester-type TPU exhibited a significant exchange reaction in the phenoxy resin blend. Furthermore, in the presence of a catalyst (e.g., zinc acetate), the exchange reaction readily occurred, and the healing efficiency improved by the addition of the catalyst and increase in the phenoxy content.
- Open Access
Characteristics of Self-Healable Copolymers of Styrene and Eugenol Terminated Polyurethane Prepolymer
With limited biomass that can be currently utilized as a renewable resource, it is important to develop a method to convert biomass into materials that can replace fossil fuel product. In this paper, eugenol, a bio-based allyl chain-substituted guaiacol, was used to synthesize self-healable copolymers. Eugenol terminated polyurethane prepolymer (ETPU) was synthesized from eugenol and polyurethane prepolymers terminated with isocyanate groups. ETPU contained two allyl groups. Self-healing copolymer networks were obtained by copolymerization of ETPU and styrene monomer via free radical polymerization. Effects of ETPU content on the properties of copolymers were then studied. These copolymers containing ETPU exhibited good thermal stability and mechanical properties. These copolymers showed higher tensile strength and elongation at break than PS. Their maximum tensile strength reached 19 MPa. In addition, these copolymers showed self-healing property at elevated temperature due to the reversible nature of urethane units in ETPU.
Open AccessCharacteristics of Self-Healable Copolymers of Styrene and Eugenol Terminated Polyurethane Prepolymer
With limited biomass that can be currently utilized as a renewable resource, it is important to develop a method to convert biomass into materials that can replace fossil fuel product. In this paper, eugenol, a bio-based allyl chain-substituted guaiacol, was used to synthesize self-healable copolymers. Eugenol terminated polyurethane prepolymer (ETPU) was synthesized from eugenol and polyurethane prepolymers terminated with isocyanate groups. ETPU contained two allyl groups. Self-healing copolymer networks were obtained by copolymerization of ETPU and styrene monomer via free radical polymerization. Effects of ETPU content on the properties of copolymers were then studied. These copolymers containing ETPU exhibited good thermal stability and mechanical properties. These copolymers showed higher tensile strength and elongation at break than PS. Their maximum tensile strength reached 19 MPa. In addition, these copolymers showed self-healing property at elevated temperature due to the reversible nature of urethane units in ETPU.
- Open Access
Effects of Isosorbide Incorporation into Flexible Polyurethane Foams: Reversible Urethane Linkages and Antioxidant Activity
Isosorbide (ISB), a nontoxic bio-based bicyclic diol composed from two fuzed furans, was incorporated into the preparation of flexible polyurethane foams (FPUFs) for use as a cell opener and to impart antioxidant properties to the resulting foam. A novel method for cell opening was designed based on the anticipated reversibility of the urethane linkages formed by ISB with isocyanate. FPUFs containing various amounts of ISB (up to 5 wt%) were successfully prepared without any noticeable deterioration in the appearance and physical properties of the resulting foams. The air permeability of these resulting FPUFs was increased and this could be further improved by thermal treatment at 160 °C. The urethane units based on ISB enabled cell window opening, as anticipated, through the reversible urethane linkage. The ISB-containing FPUFs also demonstrated better antioxidant activity by impeding discoloration. Thus, ISB, a nontoxic, bio-based diol, can be a valuable raw material (or additive) for eco-friendly FPUFs without seriously compromising the physical properties of these FPUFs.
Open AccessEffects of Isosorbide Incorporation into Flexible Polyurethane Foams: Reversible Urethane Linkages and Antioxidant Activity
Isosorbide (ISB), a nontoxic bio-based bicyclic diol composed from two fuzed furans, was incorporated into the preparation of flexible polyurethane foams (FPUFs) for use as a cell opener and to impart antioxidant properties to the resulting foam. A novel method for cell opening was designed based on the anticipated reversibility of the urethane linkages formed by ISB with isocyanate. FPUFs containing various amounts of ISB (up to 5 wt%) were successfully prepared without any noticeable deterioration in the appearance and physical properties of the resulting foams. The air permeability of these resulting FPUFs was increased and this could be further improved by thermal treatment at 160 °C. The urethane units based on ISB enabled cell window opening, as anticipated, through the reversible urethane linkage. The ISB-containing FPUFs also demonstrated better antioxidant activity by impeding discoloration. Thus, ISB, a nontoxic, bio-based diol, can be a valuable raw material (or additive) for eco-friendly FPUFs without seriously compromising the physical properties of these FPUFs.