Bastian Okto Bangkit Sentosa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Bastian Okto Bangkit Sentosa has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Mulia Orientilize
Civil Engineering Departmen, Universitas Indonesia, Kampus UI, Depok 16424, Indonesia
4 shared publications - Quoc-Bao Bui
Ton Duc Thang University
3 shared publications Josia Irwan Rastandi
Civil Engineering Department, Faculty of Engineering, Universitas Indonesia
2 shared publications- Josia Irwan Rastandi
Department of Civil Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424, Indonesia
2 shared publications - Nuraziz Handika
Universitas Indonesia, Indonesia
2 shared publications - Olivier Plé
UMR CNRS 5271, LOCIE, Université Savoie Mont-Blanc, 73370 Le Bourget du Lac, France
2 shared publications
Latest Publications
- 2 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Caractérisation d'éléments structurels en béton armé par mesures dynamiques
Les applications des mesures dynamiques sur les bâtiments existants sont nombreuses : vérification de la vulnérabilité sismique des structures qui ont été construites avant l’apparition des règles parasismiques ; auscultation de la capacité des structures en situation post-sismique ou après des modifications au voisinage (creusement d’un tunnel à côté ou démolition des immeubles voisins par exemple). A l’heure actuelle, ce type de mesure permet le diagnostic d’une structure à l’échelle globale (toute la structure) alors que l’identification et la localisation des endommagements à l’échelle locale (chaque élément de la structure) restent encore à approfondir. Dans le cadre de cette thèse, le diagnostic à l’échelle locale des structures sera étudié. Cette thèse s’insère dans un contexte national de réévaluation des structures existantes du fait du nombre important de bâtiments à réhabiliter. Au sein du LOCIE, nous pensons que le comportement global des bâtiments est certes influencé par l’interaction sol-structure mais au moins autant par la qualité des connexions des éléments de structures entre eux. Il existe un besoin de qualification de ces connexions dont la variabilité du comportement peut provenir aussi bien de défauts de mise en œuvre (positionnement des armatures,…) que du vieillissement des structures. L’objectif principal de cette thèse est de proposer une méthode pouvant caractériser les liaisons entre les éléments de structure afin de pouvoir caler un modèle numérique. Ces caractérisations devaient être possibles à partir de mesures de sollicitations dynamiques. Une première étape de ce travail consistera à caractériser sur une partie de structure une liaison. Cela sera fait sur un portique en béton armé. Par la suite, cette méthode sera adaptée à une caractérisation au sein d’une structure de bâtiment. Pour cela nous ferons appel à la notion de sous-modèle. Un modèle numérique sera associé à cette méthode aussi bien sur la connexion simple que sur l’ensemble du bâtiment. Le travail de thèse s’appuiera sur l’utilisation et le développement de techniques concernant le traitement des données dynamiques ; la réduction de modèles ; l’expérimentation en laboratoire (échelle locale et échelle d’un élément de structure) et la modélisation numérique par éléments finis à plusieurs échelles
- 2 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Caractérisation d'éléments structurels en béton armé par mesures dynamiques
Les applications des mesures dynamiques sur les bâtiments existants sont nombreuses : vérification de la vulnérabilité sismique des structures qui ont été construites avant l’apparition des règles parasismiques ; auscultation de la capacité des structures en situation post-sismique ou après des modifications au voisinage (creusement d’un tunnel à côté ou démolition des immeubles voisins par exemple). A l’heure actuelle, ce type de mesure permet le diagnostic d’une structure à l’échelle globale (toute la structure) alors que l’identification et la localisation des endommagements à l’échelle locale (chaque élément de la structure) restent encore à approfondir. Dans le cadre de cette thèse, le diagnostic à l’échelle locale des structures sera étudié. Cette thèse s’insère dans un contexte national de réévaluation des structures existantes du fait du nombre important de bâtiments à réhabiliter. Au sein du LOCIE, nous pensons que le comportement global des bâtiments est certes influencé par l’interaction sol-structure mais au moins autant par la qualité des connexions des éléments de structures entre eux. Il existe un besoin de qualification de ces connexions dont la variabilité du comportement peut provenir aussi bien de défauts de mise en œuvre (positionnement des armatures,…) que du vieillissement des structures. L’objectif principal de cette thèse est de proposer une méthode pouvant caractériser les liaisons entre les éléments de structure afin de pouvoir caler un modèle numérique. Ces caractérisations devaient être possibles à partir de mesures de sollicitations dynamiques. Une première étape de ce travail consistera à caractériser sur une partie de structure une liaison. Cela sera fait sur un portique en béton armé. Par la suite, cette méthode sera adaptée à une caractérisation au sein d’une structure de bâtiment. Pour cela nous ferons appel à la notion de sous-modèle. Un modèle numérique sera associé à cette méthode aussi bien sur la connexion simple que sur l’ensemble du bâtiment. Le travail de thèse s’appuiera sur l’utilisation et le développement de techniques concernant le traitement des données dynamiques ; la réduction de modèles ; l’expérimentation en laboratoire (échelle locale et échelle d’un élément de structure) et la modélisation numérique par éléments finis à plusieurs échelles
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2847 (1)
Recycled aggregate concrete beam: Experimental study using digital image correlation (DIC) and numerical study using multi-fibre Timoshenko beam element in CAST3M
As a part of study on recycled aggregate concrete (RAC) application on structural element, experiments on simple beam using Digital Image Correlation (DIC) results and numerical study results are presented. The experimental study involves a 3000 x 150 x 250 mm3 beam with semi-cyclic loading using DIC to investigate the load vs. deflection, strain, and cracking behavior, with comparison to measurement using LVDT and cracking formation on the sample. The numerical study is done in CAST3M using Timoshenko multi-fibre beam element with Mazars and Unilateral La Borderie concrete model along with PARFAIT_UNI for the steel model, with the objective of replicating the load vs. deflection graph and strain distribution of the experiment. From the experiment, the results for midspan deflection from DIC are similar with readings from LVDT and from the strain distribution the beam experienced flexural and inclined cracking during the loading phase, while majority of flexural cracking closed during unloading phase except two locations where permanent cracking has formed at yield limit. From the numerical study, Mazars and unilateral La Borderie concrete model along with PARFAIT_UNI steel model using multi-fibre Timoshenko beam element could approach the load vs. deflection graph of the experiment using monotonic loading. On the other hand, the numerical model shows less residual deformation and higher load capacity during loading-unloading cycle using semi-cyclic loading. The Numerical model strain distribution obtained using unilateral La Borderie concrete models cannot show specific location where cracking happens, but it can show the area where cracking will likely be distributed.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2847 (1)
Open AccessRecycled aggregate concrete beam: Experimental study using digital image correlation (DIC) and numerical study using multi-fibre Timoshenko beam element in CAST3M
As a part of study on recycled aggregate concrete (RAC) application on structural element, experiments on simple beam using Digital Image Correlation (DIC) results and numerical study results are presented. The experimental study involves a 3000 x 150 x 250 mm3 beam with semi-cyclic loading using DIC to investigate the load vs. deflection, strain, and cracking behavior, with comparison to measurement using LVDT and cracking formation on the sample. The numerical study is done in CAST3M using Timoshenko multi-fibre beam element with Mazars and Unilateral La Borderie concrete model along with PARFAIT_UNI for the steel model, with the objective of replicating the load vs. deflection graph and strain distribution of the experiment. From the experiment, the results for midspan deflection from DIC are similar with readings from LVDT and from the strain distribution the beam experienced flexural and inclined cracking during the loading phase, while majority of flexural cracking closed during unloading phase except two locations where permanent cracking has formed at yield limit. From the numerical study, Mazars and unilateral La Borderie concrete model along with PARFAIT_UNI steel model using multi-fibre Timoshenko beam element could approach the load vs. deflection graph of the experiment using monotonic loading. On the other hand, the numerical model shows less residual deformation and higher load capacity during loading-unloading cycle using semi-cyclic loading. The Numerical model strain distribution obtained using unilateral La Borderie concrete models cannot show specific location where cracking happens, but it can show the area where cracking will likely be distributed.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2847 (1) , 050012
Study of mechanical properties of steel plate using Arduino microcontroller
This paper presents the use of an open source-based technology, Arduino microcontroller, which is used for strain measurement by using strain gauge. The test was carried out in two variations, simply support beam and cantilever beam. This research used steel plates as specimens with 600mm length, 25mm width, and 3mm thickness. Specimen equipped with 3 numbers of strain gauge and a dial gauge to control the displacement that occurs. Each step of loading adds 2N until reach 10 N for simple beam and 6N for cantilever beam. The results show that in the compression zone, strain gauge show a negative value as the load increment, in other side the tensile zone, strain gauge show a positive value as the load increment. Data results are consistent in the two variations of the research conducted. The fluctuation of strain that occurs can be recorded properly by the Arduino microcontroller system equipped with a BF120 sensor, although it still has a relative high noise from the raw data recorded.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2847 (1) , 050012
Open AccessStudy of mechanical properties of steel plate using Arduino microcontroller
This paper presents the use of an open source-based technology, Arduino microcontroller, which is used for strain measurement by using strain gauge. The test was carried out in two variations, simply support beam and cantilever beam. This research used steel plates as specimens with 600mm length, 25mm width, and 3mm thickness. Specimen equipped with 3 numbers of strain gauge and a dial gauge to control the displacement that occurs. Each step of loading adds 2N until reach 10 N for simple beam and 6N for cantilever beam. The results show that in the compression zone, strain gauge show a negative value as the load increment, in other side the tensile zone, strain gauge show a positive value as the load increment. Data results are consistent in the two variations of the research conducted. The fluctuation of strain that occurs can be recorded properly by the Arduino microcontroller system equipped with a BF120 sensor, although it still has a relative high noise from the raw data recorded.
- Open Access
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 811 (1)
Damage Assessment Using Natural Frequency on Concentric Braced Frame Steel Structures
At present, structural assessment using dynamic characteristics remains to be explored. In this study, a correlation between damage index and natural frequencies of Concentric Braced Frame steel structures has been observed. The study consists of two sections: the first section presents the calculation of the damage indices of structures by means of monotonic and semicyclic pushover analyses using OpenSEES software, while the second section evaluates the structures’ natural frequencies by means of modal analyses using SAP2000 software. Our results show a trend in which with increasing amounts of lateral load, natural frequencies of the structures decrease while the damage indices increase. There is also an apparent ‘jump’ in the damage index values after the lateral loads reach their critical limits. The study results help the understanding of the structural assessment process at the global scale.
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 811 (1)
Open AccessDamage Assessment Using Natural Frequency on Concentric Braced Frame Steel Structures
At present, structural assessment using dynamic characteristics remains to be explored. In this study, a correlation between damage index and natural frequencies of Concentric Braced Frame steel structures has been observed. The study consists of two sections: the first section presents the calculation of the damage indices of structures by means of monotonic and semicyclic pushover analyses using OpenSEES software, while the second section evaluates the structures’ natural frequencies by means of modal analyses using SAP2000 software. Our results show a trend in which with increasing amounts of lateral load, natural frequencies of the structures decrease while the damage indices increase. There is also an apparent ‘jump’ in the damage index values after the lateral loads reach their critical limits. The study results help the understanding of the structural assessment process at the global scale.
- Open Access
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 811 (1)
Effect of Hinge Properties on Nonlinear Analysis of Eccentrically Steel Braced Frames
Eccentrically Braced Frame (EBF) is one of seismic resistance of steel structures. Dissipation of seismic energies is designed by allowing plastic hinges to form in link element. Design of link elements allow plastic hinge to form due to shear or flexural failure. Structural analysis using finite element software require shear plastic hinges to be modelled. It is found that hinge properties proposed by two references, FEMA 356 and Richards & Uang are different. Study of effect of hinge properties on non-linier analysis of EBF was performed. The research is limited to hinge properties of shear link of EBFs. Numerical study was conducted on one and three storey of EBFs in two and three dimensional geometric of EBFs. Two different hinge properties from FEMA 356 and Richard-Uang were compared each other. Results show that hinge properties affect the structural response. It is found that EBFs modelled by hinge properties according to Richards-Uang has close result to experimental result than modelled built by FEMA 356. The difference between FEMA 356 and Richard-Uang to experiment are 34,54% and 15,55%, respectively.
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 811 (1)
Open AccessEffect of Hinge Properties on Nonlinear Analysis of Eccentrically Steel Braced Frames
Eccentrically Braced Frame (EBF) is one of seismic resistance of steel structures. Dissipation of seismic energies is designed by allowing plastic hinges to form in link element. Design of link elements allow plastic hinge to form due to shear or flexural failure. Structural analysis using finite element software require shear plastic hinges to be modelled. It is found that hinge properties proposed by two references, FEMA 356 and Richards & Uang are different. Study of effect of hinge properties on non-linier analysis of EBF was performed. The research is limited to hinge properties of shear link of EBFs. Numerical study was conducted on one and three storey of EBFs in two and three dimensional geometric of EBFs. Two different hinge properties from FEMA 356 and Richard-Uang were compared each other. Results show that hinge properties affect the structural response. It is found that EBFs modelled by hinge properties according to Richards-Uang has close result to experimental result than modelled built by FEMA 356. The difference between FEMA 356 and Richard-Uang to experiment are 34,54% and 15,55%, respectively.
- Open Access
- 13 March 2020
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 426
Comparative study of reduced beam section modelling on SMRF steel structure
RBS (reduced beam section) as part of SMRF (special moment resisting frame) is designed to absorb energy release during earthquake. Reducing beam section force plastic hinge occur away from beam column connection. Comparative study of RBS modelling using two finite element software, OpenSEES and ETABS were conducted. OpenSEES is an open source software intended for earthquake simulations. The software provides various element and material details to ensure that the model built can represent the real structure. However, the simulation using this software is very complex. Simplified analysis of RBS using commercial software ETABS was proposed. It is found that the method has similar result with OpenSEES.
- 13 March 2020
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 426
Open AccessComparative study of reduced beam section modelling on SMRF steel structure
RBS (reduced beam section) as part of SMRF (special moment resisting frame) is designed to absorb energy release during earthquake. Reducing beam section force plastic hinge occur away from beam column connection. Comparative study of RBS modelling using two finite element software, OpenSEES and ETABS were conducted. OpenSEES is an open source software intended for earthquake simulations. The software provides various element and material details to ensure that the model built can represent the real structure. However, the simulation using this software is very complex. Simplified analysis of RBS using commercial software ETABS was proposed. It is found that the method has similar result with OpenSEES.
- Open Access
- 1 February 2020
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 426 (1)
Damage assessment of moment resisting frame structures using corelation between damage index and natural frequency
Damage index is a define scale to describe damage of the structure due to earthquake. Several studies of damage index have been carried out on reinforced structures, but not many studies performed on steel structures. Numerical research about damage index on moment resisting frame of steel structure has been conducted. Monotonic and semi-cyclic pushover analyses using OpenSEES software was carried out to obtain the index. Two paramaters that affect the damage index value are the displacement ratio and energy absorbsion. Damage index value of MRF obtained in this research is governed by the displacement ratio. The main objective of this study is to correlate damage index and the natural frequency. SAP2000 is used to get the natural frequency through modal analysis. The results show that natural frequency can be used to assess structural damage. Hence, structural health monitoring can be simplied by assesing the natural frequency.
- 1 February 2020
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 426 (1)
Open AccessDamage assessment of moment resisting frame structures using corelation between damage index and natural frequency
Damage index is a define scale to describe damage of the structure due to earthquake. Several studies of damage index have been carried out on reinforced structures, but not many studies performed on steel structures. Numerical research about damage index on moment resisting frame of steel structure has been conducted. Monotonic and semi-cyclic pushover analyses using OpenSEES software was carried out to obtain the index. Two paramaters that affect the damage index value are the displacement ratio and energy absorbsion. Damage index value of MRF obtained in this research is governed by the displacement ratio. The main objective of this study is to correlate damage index and the natural frequency. SAP2000 is used to get the natural frequency through modal analysis. The results show that natural frequency can be used to assess structural damage. Hence, structural health monitoring can be simplied by assesing the natural frequency.
- 19 June 2019
- Published by Taylor & Francis in Structural Engineering International
- Vol. 29 (3) , 396-403
Assessing Damage to Beam–Column Connections in Reinforced Concrete Structures from Vibrational Measurement Results
At present, dynamic measurements enable the diagnosis of an existing structure at a global scale (the whole structure), while the identification and assessment of local damage (at each element of the structure) remain to be explored. In this study, diagnosis at a local scale was experimentally investigated on a reinforced concrete (RC) frame structure consisting of two columns and one beam. The RC frame was loaded in several stages and dynamic measurements were recorded at each unloading stage using accelerometers. The experimental results were first presented: the appearance of damage, the evolution of natural frequencies and the stiffness changes. Then, a technique of damage characterization was applied which takes into account the semi-rigid connections of the frame. The stiffness of the connections was identified by calibrating the numerical dynamic responses with those obtained from the experiment. Fixity factors were introduced to assess the stiffness changes in the semi-rigid connections. The validity of the identified fixity factors was evaluated using the static experimental results. This study showed that the results from dynamic measurements coupled with a simple finite element model could provide a rapid and effective method to assess the damage evolution of RC frame structures.
- 19 June 2019
- Published by Taylor & Francis in Structural Engineering International
- Vol. 29 (3) , 396-403
Assessing Damage to Beam–Column Connections in Reinforced Concrete Structures from Vibrational Measurement Results
At present, dynamic measurements enable the diagnosis of an existing structure at a global scale (the whole structure), while the identification and assessment of local damage (at each element of the structure) remain to be explored. In this study, diagnosis at a local scale was experimentally investigated on a reinforced concrete (RC) frame structure consisting of two columns and one beam. The RC frame was loaded in several stages and dynamic measurements were recorded at each unloading stage using accelerometers. The experimental results were first presented: the appearance of damage, the evolution of natural frequencies and the stiffness changes. Then, a technique of damage characterization was applied which takes into account the semi-rigid connections of the frame. The stiffness of the connections was identified by calibrating the numerical dynamic responses with those obtained from the experiment. Fixity factors were introduced to assess the stiffness changes in the semi-rigid connections. The validity of the identified fixity factors was evaluated using the static experimental results. This study showed that the results from dynamic measurements coupled with a simple finite element model could provide a rapid and effective method to assess the damage evolution of RC frame structures.
- Open Access
- 4 February 2018
- Published by MDPI AG in Sustainability
- Vol. 10 (2) , 401
Sustainable RC Beam-Column Connections with Headed Bars: A Formula for Shear Strength Evaluation
Beam-column joints are critical regions for reinforced concrete (RC) frames subjected to earthquakes. The steel reinforcement is, in general, highly concentrated in these zones. This is why in many cases, headed bars are used. A headed bar is a longitudinal steel reinforcement whose end has a special button added to reduce the bonding length of the steel rebar. This paper establishes a formula predicting the shear strength of exterior RC beam-column connections where the beam longitudinal reinforcements use headed bars. A database was collected, which contained 30 experimental data about the exterior beam-column joints using headed bars and subjected to quasi-static cyclic loading. First, from the collected database, a statistical study was carried out to identify the most influencing parameters on the shear strength of the beam-column joints tested. The three most important parameters were identified and an empirical modified formula was developed based on the formula existing in the standards. The study showed that the results obtained from the modified formula proposed in the present study were closer to the experimental results than that obtained from the formula existing in the standards. Finally, a numerical study was performed on two T-form RC structures and the numerical results were compared with the prediction calculated from the modified formula proposed. For two investigated cases, the proposed formula provided the results in the safety side and the differences with the numerical results were less than 20%. Thus, the proposed formula can be used for a rapid assessment of the shear strength of RC joints using headed bars.
- 4 February 2018
- Published by MDPI AG in Sustainability
- Vol. 10 (2) , 401
Open AccessSustainable RC Beam-Column Connections with Headed Bars: A Formula for Shear Strength Evaluation
Beam-column joints are critical regions for reinforced concrete (RC) frames subjected to earthquakes. The steel reinforcement is, in general, highly concentrated in these zones. This is why in many cases, headed bars are used. A headed bar is a longitudinal steel reinforcement whose end has a special button added to reduce the bonding length of the steel rebar. This paper establishes a formula predicting the shear strength of exterior RC beam-column connections where the beam longitudinal reinforcements use headed bars. A database was collected, which contained 30 experimental data about the exterior beam-column joints using headed bars and subjected to quasi-static cyclic loading. First, from the collected database, a statistical study was carried out to identify the most influencing parameters on the shear strength of the beam-column joints tested. The three most important parameters were identified and an empirical modified formula was developed based on the formula existing in the standards. The study showed that the results obtained from the modified formula proposed in the present study were closer to the experimental results than that obtained from the formula existing in the standards. Finally, a numerical study was performed on two T-form RC structures and the numerical results were compared with the prediction calculated from the modified formula proposed. For two investigated cases, the proposed formula provided the results in the safety side and the differences with the numerical results were less than 20%. Thus, the proposed formula can be used for a rapid assessment of the shear strength of RC joints using headed bars.
- 21 October 2017
- Published by Springer Nature
- p. 59-67
A Numerical Modeling of RC Beam-Column Joints Compared to Experimental Results
- 21 October 2017
- Published by Springer Nature
- p. 59-67
A Numerical Modeling of RC Beam-Column Joints Compared to Experimental Results