Wei Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wei Zhu has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Yuan Deng
School of Materials Science and Engineering, Beihang University, Beijing, China
23 shared publications Yuedong Yu
School of Materials Science and Engineering, Beihang University, Beijing 100191, China
12 shared publicationsJie Zhou
School of Materials Science and Engineering Beihang University Beijing 100191 China
9 shared publicationsQingqing Zhang
Key Laboratory of Intelligent Sensing Materials and Chip Integration Technology of Zhejiang Province Hangzhou Innovation Institute of Beihang University Hangzhou 310051 China
9 shared publicationsYuan Deng
School of Materials Science and Engineering Beihang University Beijing 100191 China
7 shared publicationsYue Huang
School of Materials Science and Engineering, Beihang University, Beijing, China
5 shared publications
Latest Publications
- 21 August 2026
- Published by Springer Nature in ENGINEERING Chemical Engineering
- Vol. 20 (10) , 82
Advancing lithium-ion batteries through integrated health monitoring and intelligent thermal management
- 21 August 2026
- Published by Springer Nature in ENGINEERING Chemical Engineering
- Vol. 20 (10) , 82
Advancing lithium-ion batteries through integrated health monitoring and intelligent thermal management
- Open Access
- 8 May 2025
- Published by Springer Nature in npj Flexible Electronics
- Vol. 9 (1) , 1-13
Programmable high-sensitivity iontronic pressure sensors support broad human-interactive perception and identification
- 8 May 2025
- Published by Springer Nature in npj Flexible Electronics
- Vol. 9 (1) , 1-13
Open AccessProgrammable high-sensitivity iontronic pressure sensors support broad human-interactive perception and identification
- 27 June 2024
- Published by Wiley in Small Methods
- Vol. 8 (12) , e2400589
Direct Melt‐Calendaring of Highly Textured (Bi,Sb) 2 Te 3 Thick Films: Superior Thermoelectric and Mechanical Performance via Strain Engineering
The evolutions of chip thermal management and micro energy harvesting put forward urgent need for micro thermoelectric devices. Nevertheless, low‐performance thermoelectric thick films as well as the complicated precision cutting process for hundred‐micron thermoelectric legs still remain the bottleneck hindering the advancement of micro thermoelectric devices. In this work, an innovative direct melt‐calendaring manufacturing technology is first proposed with specially designed and assembled equipment, that enables direct, rapid, and cost‐effective continuous manufacturing of Bi 2 Te 3 ‐based films with thickness of hundred microns. Based on the strain engineering with external glass coating confinement and controlled calendaring deformation degree, enhanced thermoelectric performance has been achieved for (Bi,Sb) 2 Te 3 thick films with highly textured nanocrystals, which can promote carrier mobility over 182.6 cm 2 V −1 s −1 and bring out a record‐high zT value of 0.96 and 1.16 for n‐type and p‐type (Bi,Sb) 2 Te 3 thick films, respectively. The nanoscale interfaces also further improve the mechanical strength with excellent elastic modules (over 42.0 GPa) and hardness (over 1.7 GPa), even superior to the commercial zone‐melting ingots and comparable to the hot‐extrusion (Bi,Sb) 2 Te 3 alloys. This new fabrication strategy is versatile to a wide range of inorganic thermoelectric thick films, which lays a solid foundation for the development of micro thermoelectric devices.
- 27 June 2024
- Published by Wiley in Small Methods
- Vol. 8 (12) , e2400589
Direct Melt‐Calendaring of Highly Textured (Bi,Sb) 2 Te 3 Thick Films: Superior Thermoelectric and Mechanical Performance via Strain Engineering
The evolutions of chip thermal management and micro energy harvesting put forward urgent need for micro thermoelectric devices. Nevertheless, low‐performance thermoelectric thick films as well as the complicated precision cutting process for hundred‐micron thermoelectric legs still remain the bottleneck hindering the advancement of micro thermoelectric devices. In this work, an innovative direct melt‐calendaring manufacturing technology is first proposed with specially designed and assembled equipment, that enables direct, rapid, and cost‐effective continuous manufacturing of Bi 2 Te 3 ‐based films with thickness of hundred microns. Based on the strain engineering with external glass coating confinement and controlled calendaring deformation degree, enhanced thermoelectric performance has been achieved for (Bi,Sb) 2 Te 3 thick films with highly textured nanocrystals, which can promote carrier mobility over 182.6 cm 2 V −1 s −1 and bring out a record‐high zT value of 0.96 and 1.16 for n‐type and p‐type (Bi,Sb) 2 Te 3 thick films, respectively. The nanoscale interfaces also further improve the mechanical strength with excellent elastic modules (over 42.0 GPa) and hardness (over 1.7 GPa), even superior to the commercial zone‐melting ingots and comparable to the hot‐extrusion (Bi,Sb) 2 Te 3 alloys. This new fabrication strategy is versatile to a wide range of inorganic thermoelectric thick films, which lays a solid foundation for the development of micro thermoelectric devices.
- 27 June 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (27) , 35815-35824
Localized Surface Doping Induced Ultralow Contact Resistance between Metal and (Bi,Sb)2Te3 Thermoelectric Films
Micro thermoelectric devices are expected to further improve the cooling density for the temperature control of electronic devices; nevertheless, the high contact resistivity between metals and semiconductors critically limits their applications, especially in chip cooling with extremely high heat flux. Herein, based on the calculated results, a low specific contact resistivity of ∼10-7 Ω cm2 at the interface is required to guarantee a desirable cooling power density of micro devices. Thus, we developed a generally applicable interfacial modulation strategy via localized surface doping of thermoelectric films, and the feasibility of such a doping approach for both n/p-type (Bi,Sb)2Te3 films was demonstrated, which can effectively increase the surface-majority carrier concentration explained by the charge transfer mechanism. With a proper doping level, ultralow specific contact resistivities at the interfaces are obtained for n-type (6.71 × 10-8 Ω cm2) and p-type (3.70 × 10-7 Ω cm2) (Bi,Sb)2Te3 layers, respectively, which is mainly attributed to the carrier tunneling enhancement with a narrowed interfacial contact barrier width. This work provides an effective scheme to further reduce the internal resistance of micro thermoelectric coolers, which can also be extended as a kind of universal interfacial modification technique for micro semiconductor devices.
- 27 June 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (27) , 35815-35824
Localized Surface Doping Induced Ultralow Contact Resistance between Metal and (Bi,Sb)2Te3 Thermoelectric Films
Micro thermoelectric devices are expected to further improve the cooling density for the temperature control of electronic devices; nevertheless, the high contact resistivity between metals and semiconductors critically limits their applications, especially in chip cooling with extremely high heat flux. Herein, based on the calculated results, a low specific contact resistivity of ∼10-7 Ω cm2 at the interface is required to guarantee a desirable cooling power density of micro devices. Thus, we developed a generally applicable interfacial modulation strategy via localized surface doping of thermoelectric films, and the feasibility of such a doping approach for both n/p-type (Bi,Sb)2Te3 films was demonstrated, which can effectively increase the surface-majority carrier concentration explained by the charge transfer mechanism. With a proper doping level, ultralow specific contact resistivities at the interfaces are obtained for n-type (6.71 × 10-8 Ω cm2) and p-type (3.70 × 10-7 Ω cm2) (Bi,Sb)2Te3 layers, respectively, which is mainly attributed to the carrier tunneling enhancement with a narrowed interfacial contact barrier width. This work provides an effective scheme to further reduce the internal resistance of micro thermoelectric coolers, which can also be extended as a kind of universal interfacial modification technique for micro semiconductor devices.
- Open Access
- 10 August 2023
- Published by Elsevier in Journal of Materiomics
- Vol. 10 (2) , 480-489
Enhanced electrical and mechanical properties of Bi2Te3-based thermoelectric thick films enabled by a practical dynamic regulation strategy
- 10 August 2023
- Published by Elsevier in Journal of Materiomics
- Vol. 10 (2) , 480-489
Open AccessEnhanced electrical and mechanical properties of Bi2Te3-based thermoelectric thick films enabled by a practical dynamic regulation strategy
- 17 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (17) , 19409-19416
Ultrasmall and Ultrathin Ni-Based Resistance Temperature Detector Integrated in Micro Thermoelectric Devices for In Situ Temperature Measurement
With the ever-increasing demand of miniature chip cooling and self-powered technology, more attention has arisen on micro thermoelectric devices. Nevertheless, accurate temperature and performance evaluations for micro thermoelectric devices are still challenging due to their high element density and small size. Herein, an in situ integration method using ultrasmall and ultrathin resistance temperature detectors is developed to precisely characterize temperatures across thin thermoelectric legs under actual testing scenarios. With theoretical analysis based on a one-dimensional thermal resistance model, the ratio of effective temperature difference across the thermoelectric leg increases to 33.97% comparing with 11.04% using commercial thermocouples. Then, fabrication of the resistance temperature detector is shown and a temperature coefficient of resistance of 0.336% °C -1 with high linearity, a response time of 43 ms, a resolution of 0.1 °C, and good compatibility is exhibited. By integrating the detector on a leg of a thermoelectric device, the in situ temperature of a micro thermoelectric device is measured, indicating an increase of 201.2% of the output thermoelectric voltage, after temperature correction, as well as an exponential enhancement of power density. This in situ temperature measurement method can be extended to further guide performance evaluations for various micro system.
- 17 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (17) , 19409-19416
Ultrasmall and Ultrathin Ni-Based Resistance Temperature Detector Integrated in Micro Thermoelectric Devices for In Situ Temperature Measurement
With the ever-increasing demand of miniature chip cooling and self-powered technology, more attention has arisen on micro thermoelectric devices. Nevertheless, accurate temperature and performance evaluations for micro thermoelectric devices are still challenging due to their high element density and small size. Herein, an in situ integration method using ultrasmall and ultrathin resistance temperature detectors is developed to precisely characterize temperatures across thin thermoelectric legs under actual testing scenarios. With theoretical analysis based on a one-dimensional thermal resistance model, the ratio of effective temperature difference across the thermoelectric leg increases to 33.97% comparing with 11.04% using commercial thermocouples. Then, fabrication of the resistance temperature detector is shown and a temperature coefficient of resistance of 0.336% °C -1 with high linearity, a response time of 43 ms, a resolution of 0.1 °C, and good compatibility is exhibited. By integrating the detector on a leg of a thermoelectric device, the in situ temperature of a micro thermoelectric device is measured, indicating an increase of 201.2% of the output thermoelectric voltage, after temperature correction, as well as an exponential enhancement of power density. This in situ temperature measurement method can be extended to further guide performance evaluations for various micro system.
Realizing the Accurate Measurements of Thermal Conductivity over a Wide Range by Scanning Thermal Microscopy Combined with Quantitative Prediction of Thermal Contact Resistance
Quantitative thermal performance measurements and thermal management at the micro‐/nano scale are becoming increasingly important as the size of electronic components shrinks. Scanning thermal microscopy (SThM) is an emerging method with high spatial resolution that accurately reflects changes in local thermal signals based on a thermally sensitive probe. However, because of the unclear thermal resistance at the probe‐sample interface, quantitative characterization of thermal conductivity for different kinds of materials still remains limited. In this paper, the heat transfer process considering the thermal contact resistance between the probe and sample surface is analyzed using finite element simulation and thermal resistance network model. On this basis, a mathematical empirical function is developed applicable to a variety of material systems, which depicts the relationship between the thermal conductivity of the sample and the probe temperature. The proposed model is verified by measuring ten materials with a wide thermal conductivity range, and then further validated by two materials with unknown thermal conductivity. In conclusion, this work provides the prospect of achieving quantitative characterization of thermal conductivity over a wide range and further enables the mapping of local thermal conductivity to microstructures or phases of materials.
Realizing the Accurate Measurements of Thermal Conductivity over a Wide Range by Scanning Thermal Microscopy Combined with Quantitative Prediction of Thermal Contact Resistance
Quantitative thermal performance measurements and thermal management at the micro‐/nano scale are becoming increasingly important as the size of electronic components shrinks. Scanning thermal microscopy (SThM) is an emerging method with high spatial resolution that accurately reflects changes in local thermal signals based on a thermally sensitive probe. However, because of the unclear thermal resistance at the probe‐sample interface, quantitative characterization of thermal conductivity for different kinds of materials still remains limited. In this paper, the heat transfer process considering the thermal contact resistance between the probe and sample surface is analyzed using finite element simulation and thermal resistance network model. On this basis, a mathematical empirical function is developed applicable to a variety of material systems, which depicts the relationship between the thermal conductivity of the sample and the probe temperature. The proposed model is verified by measuring ten materials with a wide thermal conductivity range, and then further validated by two materials with unknown thermal conductivity. In conclusion, this work provides the prospect of achieving quantitative characterization of thermal conductivity over a wide range and further enables the mapping of local thermal conductivity to microstructures or phases of materials.
- Open Access
- 13 March 2023
- Published by Elsevier in Progress in Natural Science: Materials International
- Vol. 33 (1) , 55-66
Recent progress in high-resolution tactile sensor array: From sensor fabrication to advanced applications
- 13 March 2023
- Published by Elsevier in Progress in Natural Science: Materials International
- Vol. 33 (1) , 55-66
Open AccessRecent progress in high-resolution tactile sensor array: From sensor fabrication to advanced applications