Marta Ruscello
Marta Ruscello has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Gerardo Hernandez-Sosa
Institute for Automation and Applied Informatics Karlsruhe Institute of Technology Eggenstein‐Leopoldshafen Germany
4 shared publications Eric Mankel
InnovationLab GmbH
2 shared publications- Uli Lemmer
Light Technology Institute Karlsruhe Institute of Technology (KIT) Karlsruhe Germany
2 shared publications Wolfgang Kowalsky
InnovationLab GmbH
2 shared publicationsAlejandro L. Briseno
1 shared publicationAnnemarie Pucci
1 shared publication
Latest Publications
- Open Access
- 30 November 2020
- Published by Wiley in Advanced Electronic Materials
- Vol. 7 (1)
Aerosol‐Jet‐Printed Donor‐Blocking Layer for Organic Photodiodes
Organic photodiodes (OPDs) are optical sensors combining high performance, lightweight mechanical flexibility, and processability from solution. Their fabrication by industrial printing techniques opens a wide range of innovative applications for emerging fields in sensing and the Internet of Things. They typically consist of printed multilayers with functionalities to absorb light, to extract charges, or to reduce detection noise. However, the printing of such device architecture poses a challenge as the deposition of a material can lead to disruption of film morphology or intermixing of materials if its solvent interacts with the previously deposited layer. This work proposes a process to print multilayers from the same solvent system utilizing the aerosol‐jet technique. By fine adjustment of the aerosol properties through the tube temperature (TTube), the drying time of poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) printed layers is significantly reduced. This allows its deposition onto a P3HT‐based bulk‐heterojunction (BHJ) without negatively affecting its performance. The additional printed P3HT layer, spatially extends the donor region of the BHJ, providing ideal hole extraction and simultaneous noise reduction by the blocking of injected electrons. This donor blocking layer (DBL) yields a noise reduction of two orders of magnitude in OPDs operated under −2 V reverse bias.
- 30 November 2020
- Published by Wiley in Advanced Electronic Materials
- Vol. 7 (1)
Open AccessAerosol‐Jet‐Printed Donor‐Blocking Layer for Organic Photodiodes
Organic photodiodes (OPDs) are optical sensors combining high performance, lightweight mechanical flexibility, and processability from solution. Their fabrication by industrial printing techniques opens a wide range of innovative applications for emerging fields in sensing and the Internet of Things. They typically consist of printed multilayers with functionalities to absorb light, to extract charges, or to reduce detection noise. However, the printing of such device architecture poses a challenge as the deposition of a material can lead to disruption of film morphology or intermixing of materials if its solvent interacts with the previously deposited layer. This work proposes a process to print multilayers from the same solvent system utilizing the aerosol‐jet technique. By fine adjustment of the aerosol properties through the tube temperature (TTube), the drying time of poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) printed layers is significantly reduced. This allows its deposition onto a P3HT‐based bulk‐heterojunction (BHJ) without negatively affecting its performance. The additional printed P3HT layer, spatially extends the donor region of the BHJ, providing ideal hole extraction and simultaneous noise reduction by the blocking of injected electrons. This donor blocking layer (DBL) yields a noise reduction of two orders of magnitude in OPDs operated under −2 V reverse bias.
- Open Access
- 8 April 2019
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 3 (6) , 1418-1426
Nanocomposite of nickel oxide nanoparticles and polyethylene oxide as printable hole transport layer for organic solar cells
We focused on the low-temperature fabrication (∼100 °C) of nanoparticle-based NiOx hole transport layers for organic solar cells. We used high molecular weight polyethylene oxide (PEO) as a sacrificial additive for the processing of NiOx nanoparticle (NP) dispersions which is removed from the film by oxygen plasma prior to the active layer deposition. Through comprehensive characterization by optical, electrical and scanning probe techniques we show that an optimal NiOx : PEO ratio allows to disperse the NPs, hindering their aggregation and maximizing device performance. Finally, we demonstrate the practical relevance of our approach by inkjet printing the NiOx:PEO blends to produce hole transport layers (HTLs) for P3HT:PCBM bulk heterojunction solar cells with comparable efficiencies to devices produced with high-temperature precursor-based approaches. The utilization of P3HT:PCBM as active layer material is meant to offer an optimum standard for the introduction of the presented HTL processing approach and its applicability to a wider range of hybrid systems and multilayer optoelectronic devices.
- 8 April 2019
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 3 (6) , 1418-1426
Open AccessNanocomposite of nickel oxide nanoparticles and polyethylene oxide as printable hole transport layer for organic solar cells
We focused on the low-temperature fabrication (∼100 °C) of nanoparticle-based NiOx hole transport layers for organic solar cells. We used high molecular weight polyethylene oxide (PEO) as a sacrificial additive for the processing of NiOx nanoparticle (NP) dispersions which is removed from the film by oxygen plasma prior to the active layer deposition. Through comprehensive characterization by optical, electrical and scanning probe techniques we show that an optimal NiOx : PEO ratio allows to disperse the NPs, hindering their aggregation and maximizing device performance. Finally, we demonstrate the practical relevance of our approach by inkjet printing the NiOx:PEO blends to produce hole transport layers (HTLs) for P3HT:PCBM bulk heterojunction solar cells with comparable efficiencies to devices produced with high-temperature precursor-based approaches. The utilization of P3HT:PCBM as active layer material is meant to offer an optimum standard for the introduction of the presented HTL processing approach and its applicability to a wider range of hybrid systems and multilayer optoelectronic devices.
- 2 May 2018
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 34 (21) , 5964-5970
Substrate-Independent Surface Energy Tuning via Siloxane Treatment for Printed Electronics
Digital printing enables solution processing of functional materials and opens a new route to fabricate low-cost electronic devices. One crucial parameter that affects the wettability of inks for all printing techniques is the surface free energy (SFE) of the substrate. Siloxanes, with their huge variety of sidechains and their ability to form self-assembled monolayers (SAMs), offer exhaustive control of the substrates SFE from hydrophilic to hydrophobic. Thus, siloxane treatment is a suitable approach to adjust the substrate conditions to the desired ink instead of optimizing the ink to an arbitrary substrate. In this work, the influence of different fluorinated and non-fluorinated siloxanes on the SFE of different substrates, such as polymers, glasses and metals is examined. By mixing several siloxanes we demonstrate a fine tuning of the surface energy. The polar and dispersive components of the SFE are determined by the Owens-Wendt-Rabel-Kaelble (OWRK)-method. Furthermore, the impact of the siloxanes and therefore the SFE on the pinning of droplets and wet films is assessed via dynamic contact angle measurements. SFE-optimized substrates enable tailoring the resolution of inkjet printed silver structures. A nano-particulate silver ink was used for printing single drops, lines and source-drain electrodes for transistors. These were examined in terms of diameter, edge quality and functionality. We show that by adjusting the SFE of an arbitrary substrate, the printed resolution is substantially increased by minimizing the printed drop size by up to 70 %.
- 2 May 2018
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 34 (21) , 5964-5970
Substrate-Independent Surface Energy Tuning via Siloxane Treatment for Printed Electronics
Digital printing enables solution processing of functional materials and opens a new route to fabricate low-cost electronic devices. One crucial parameter that affects the wettability of inks for all printing techniques is the surface free energy (SFE) of the substrate. Siloxanes, with their huge variety of sidechains and their ability to form self-assembled monolayers (SAMs), offer exhaustive control of the substrates SFE from hydrophilic to hydrophobic. Thus, siloxane treatment is a suitable approach to adjust the substrate conditions to the desired ink instead of optimizing the ink to an arbitrary substrate. In this work, the influence of different fluorinated and non-fluorinated siloxanes on the SFE of different substrates, such as polymers, glasses and metals is examined. By mixing several siloxanes we demonstrate a fine tuning of the surface energy. The polar and dispersive components of the SFE are determined by the Owens-Wendt-Rabel-Kaelble (OWRK)-method. Furthermore, the impact of the siloxanes and therefore the SFE on the pinning of droplets and wet films is assessed via dynamic contact angle measurements. SFE-optimized substrates enable tailoring the resolution of inkjet printed silver structures. A nano-particulate silver ink was used for printing single drops, lines and source-drain electrodes for transistors. These were examined in terms of diameter, edge quality and functionality. We show that by adjusting the SFE of an arbitrary substrate, the printed resolution is substantially increased by minimizing the printed drop size by up to 70 %.
- Open Access
- 1 November 2017
- Published by Elsevier in Organic Electronics
- Vol. 50, 384-388
Electron injection and interfacial trap passivation in solution-processed organic light-emitting diodes using a polymer zwitterion interlayer
- 1 November 2017
- Published by Elsevier in Organic Electronics
- Vol. 50, 384-388
Open AccessElectron injection and interfacial trap passivation in solution-processed organic light-emitting diodes using a polymer zwitterion interlayer