ALAlenka Šalej Lah

Alenka Šalej Lah

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alenka Šalej Lah has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comparative Characterization of NiTi Filaments and NiTi Knit-Induced Air-Gap Effects on Heat Transfer in a Smart Textile System

    by Alenka Šalej Lah

    This article presents a comparison of the different diameters and characterization of nickel–titanium (NiTi) alloy and the effect of an NiTi knit-induced air gap on heat transfer in a smart textile system. Weft-knitted fabric was produced using commercially available cold-worked NiTi wires (filaments), enabling active thermal insulation in protective garments by adjusting the air gap between two fabric layers in response to changes in environmental temperature. For this study, NiTi alloy filaments containing 54.8 wt. % nickel and 45.2 wt. % titanium with a diameter of 100 μm was used. The transition temperatures of the NiTi filaments were tailored for the intended application, with the austenite start temperature set at approximately 70 °C and the martensite start temperature set at around 20 °C. Various methods for determining transition temperatures were compared, including differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and electrical resistance measurements (ERM), all of which yielded consistent results. Mechanical properties were evaluated through tensile tests conducted with an Instron dynamometer at room temperature (20 °C) and in a heated chamber at 100 °C. The stress-strain response of the annealed NiTi alloy exhibited the characteristic four-stage behaviour typical of shape memory materials. All obtained results were also compared with previously reported data for NiTi alloy filaments with a diameter of 200 μm, showing good agreement. In addition, the impact of the NiTi knit-induced air gap on heat transfer behaviour in thermal protective composites was investigated. This study confirms that 100 μm NiTi filaments can be effectively optimized for smart textile applications through controlled annealing, with heat treatment at 500 °C producing suitable transformation temperatures consistently validated using DSC, DMA and ERM methods. Additionally, integrating an annealed NiTi knit into a textile composite increases the air gap at elevated temperatures, thereby reducing heat transfer and significantly enhancing the thermal insulation and adaptive performance of the smart textile system.


  • THE INFLUENCE OF CHEMICAL COMPOSITION AND HEAT TREATMENT ON THE MECHANICAL PROPERTIES AND WORKABILITY OF THE ALUMINIUM ALLOY EN AW 5454

    by Alenka Šalej Lah, Maja Vončina, Irena Paulin, Jožef Medved, Peter Fajfar, Darja Volšak

    The influence of chemical composition and heat treatment on the mechanical properties and formability of the selected commercial aluminium alloy EN AW 5454 was investigated. The main properties of alloy 5454 from the AA 5xxx series are very good corrosion resistant and has good formability. From the cast slab a 50 mm thick slice was taken in the width cross section in the slab centre. One half of the slice was homogenised for 10 hours at a temperature of 530 °C. The cast and homogenised samples were investigated using light and scanning electron microscopy. For the study of the influence of the heat treatment, samples in the as-cast state were annealed in the laboratory furnace at a temperature of 530 °C for 4, 6, 8, 10 and 12 hours. To study the influence of chemical composition, four different samples were prepared: the first without additions, the second with an addition of 1 wt% Mn, the third with 3 wt% Mg and the fourth with an addition of both elements, Mn and Mg. The XRF analyses confirmed the desired chemical composition of all four produced alloys. Half of each alloy’s sample was homogenised at the same temperature and time as the base alloy in the as-cast state. The hot deformation behaviour of the different alloys was investigated using cylindrical hot compression tests performed on a Gleeble 1500D thermo-mechanical simulator. By comparing flow curves a high influence of the thermo-mechanical parameters on the alloy formability can be seen. The alloy has good workability and with the addition of Mn and Mg, the stress values are higher than those of the base alloy.


  • Open Access

    A NiTi alloy weft knitted fabric for smart firefighting clothing

    by Alenka Šalej Lah, Peter Fajfar, Goran Kugler, Tatjana Rijavec

    A prototype of a new shape-memory nitinol knitted fabric intended for use as an active thermal insulating interlining in firefighting protective clothing was developed in the study presented in this paper. Weft knitted fabrics were made from commercially available cold-worked nickel titanium alloy monofils. Knits were made on a manual knitting machine from a monofil measuring 0.1 mm in diameter, while a hand-made knit was prepared from a monofil measuring 0.2 mm in diameter. Nitinol fabrics were annealed at 500 °C to achieve an austenite transition temperature of 75 °C. A special constructed mould made of a steel frame and aluminium domes measuring 30 and 20 mm in height was used to give the nitinol fabrics a new temporary shape. A two-way, shape-memory effect of the nitinol fabrics was achieved using a 15-cycle training process. The achieved shape-memory effect was tested in a heated chamber at 100 °C, where bulges measuring 12–25 mm in height occurred. NiTi knits made from finer monofil were the most successful shape-memory knits. They were machine knitted and achieved sufficiently high bulges, measuring 18 or 12 mm, that facilitated large enough air gaps for effective thermal protection. A smart textile system was prepared by inserting the trained nitinol fabric into a pocket made from two textile fabric layers sewn together. When it was exposed to environmental temperatures of 75 °C and higher, it instantly changed its form from a two-dimensional shape to a three-dimensional shape, while increasing the air gap in the pocket. A quilted fabric made from such a smart textile system could be used in firefighting protective clothing to locally improve thermal insulation and protect the human skin from overheating or burns.