Kentaro Takagi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kentaro Takagi has a total of 139 co-authors. Here are the top co-authors by number of shared publications:
- Kinji Asaka
National Institute of Advanced Industrial Science and Technology (AIST)
23 shared publications - Tsuyoshi Inoue
Nagoya University, Nagoya, Japan
20 shared publications Zhi-Wei Luo
Kobe University
12 shared publicationsYoshikazu Hayakawa
Nagoya Univ. (Japan)
10 shared publications- Ken Masuya
Faculty of Engineering, University of Miyazaki, Miyazaki, Japan
9 shared publications Kinji Asaka
National Institute of Advanced Industrial Science and Technology (AIST)
8 shared publications
Latest Publications
- Open Access
The Analytical Solutions to a Cation–Water Coupled Multiphysics Model of IPMC Sensors
Ionic polymer–metal composite (IPMC) sensors generate voltages or currents when subjected to deformation. The magnitude and time constant of the electrical response vary significantly with ambient humidity and water content. However, most conventional physical models focus solely on cation dynamics and do not consider water dynamics. In addition to cation dynamics, Zhu’s model explicitly incorporates the dynamics of water. Consequently, Zhu’s model is considered one of the most promising approaches for physical modeling of IPMC sensors. This paper presents exact analytical solutions to Zhu’s model of IPMC sensors for the first time. The derivation method transforms Zhu’s model into the frequency domain using Laplace transform-based analysis together with linear approximation, and subsequently solves it as a boundary value problem of a set of linear ordinary differential equations. The resulting solution is expressed as a transfer function. The input variable is the applied bending deformation, and the output variables include the open-circuit voltage or short-circuit current at the sensor terminals, as well as the distributions of cations, water molecules, and electric potential within the polymer. The obtained transfer functions are represented by irrational functions, which typically arise as solutions to a system of partial differential equations. Furthermore, this paper presents analytical approximations of the step response of the sensor voltage or current by approximating the obtained transfer functions. The steady-state and maximum values of the time response are derived from these analytical approximations. Additionally, the relaxation behavior of the sensor voltage is characterized by a key parameter newly derived from the analytical approximation presented in this paper.
Open AccessThe Analytical Solutions to a Cation–Water Coupled Multiphysics Model of IPMC Sensors
Ionic polymer–metal composite (IPMC) sensors generate voltages or currents when subjected to deformation. The magnitude and time constant of the electrical response vary significantly with ambient humidity and water content. However, most conventional physical models focus solely on cation dynamics and do not consider water dynamics. In addition to cation dynamics, Zhu’s model explicitly incorporates the dynamics of water. Consequently, Zhu’s model is considered one of the most promising approaches for physical modeling of IPMC sensors. This paper presents exact analytical solutions to Zhu’s model of IPMC sensors for the first time. The derivation method transforms Zhu’s model into the frequency domain using Laplace transform-based analysis together with linear approximation, and subsequently solves it as a boundary value problem of a set of linear ordinary differential equations. The resulting solution is expressed as a transfer function. The input variable is the applied bending deformation, and the output variables include the open-circuit voltage or short-circuit current at the sensor terminals, as well as the distributions of cations, water molecules, and electric potential within the polymer. The obtained transfer functions are represented by irrational functions, which typically arise as solutions to a system of partial differential equations. Furthermore, this paper presents analytical approximations of the step response of the sensor voltage or current by approximating the obtained transfer functions. The steady-state and maximum values of the time response are derived from these analytical approximations. Additionally, the relaxation behavior of the sensor voltage is characterized by a key parameter newly derived from the analytical approximation presented in this paper.
- Open Access
- 12 November 2025
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 397
Electroadhesive dielectric elastomer actuator for vibration excitation of mechanical structure
- 12 November 2025
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 397
Open AccessElectroadhesive dielectric elastomer actuator for vibration excitation of mechanical structure
- Open Access
- 1 March 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (3) , 035047
Active vibration control for thin curved structures using dielectric elastomer actuators
This study proposes an active vibration control technique for pipe structures using dielectric elastomer actuators (DEAs). Vibrations in pipe structures must be eliminated to improve their mechanical reliability, and active vibration control techniques can be applied for effective vibration suppression. Soft actuators, which can completely fit pipe structures with complex-shaped surfaces, are required to transfer their vibration reduction forces to the target. DEA is suitable for this kind of target structure because DEA is characterized by high stretchability, flexibility, large deformation, and fast response. By applying the DEA, the effectiveness of vibration control for the pipe structure was experimentally demonstrated. A stacked DEA was fabricated and attached to the target structure. Its shape and placement were determined based on a modal analysis of the target structure. A control system, in which the controller for the active vibration control was designed based on H ∞ control theory, was composed. The vibration control experiment was conducted using the controller with a digital control system, and the vibration reduction effect was evaluated based on the frequency response of the target pipe structure.
- 1 March 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (3) , 035047
Open AccessActive vibration control for thin curved structures using dielectric elastomer actuators
This study proposes an active vibration control technique for pipe structures using dielectric elastomer actuators (DEAs). Vibrations in pipe structures must be eliminated to improve their mechanical reliability, and active vibration control techniques can be applied for effective vibration suppression. Soft actuators, which can completely fit pipe structures with complex-shaped surfaces, are required to transfer their vibration reduction forces to the target. DEA is suitable for this kind of target structure because DEA is characterized by high stretchability, flexibility, large deformation, and fast response. By applying the DEA, the effectiveness of vibration control for the pipe structure was experimentally demonstrated. A stacked DEA was fabricated and attached to the target structure. Its shape and placement were determined based on a modal analysis of the target structure. A control system, in which the controller for the active vibration control was designed based on H ∞ control theory, was composed. The vibration control experiment was conducted using the controller with a digital control system, and the vibration reduction effect was evaluated based on the frequency response of the target pipe structure.
- 8 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (4) , 11094-11101
Wire-Storage Pantograph Mechanism for Strain and Force Amplification of a Twisted and Coiled Polymer Fiber
A twisted and coiled polymer fiber (TCPF) is a soft thermal actuator increasingly used in current robotics applications. When implementing TCPF in robotics applications, amplifying the TCPF strain and force is necessary to obtain the desired performance. Therefore, this study proposes a mechanism to amplify the strain and force of a TCPF. Considering the TCPF as a wire, the fixed and movable pulley mechanisms are available to amplify the TCPF strain and force, respectively. However, the amplification mechanism becomes bulky when the fixed pulleys are installed separately from the movable pulleys; thus, the TCPF utility reduces. This study focuses on two characteristics of the pantograph to design a compact amplification mechanism. The first characteristic is that the pulleys on the pantograph diagonal axes can be used as a movable pulley mechanism. The other characteristic is that the pantograph circumference can be a fixed pulley mechanism, as the circumference is always invariant. Based on these characteristics, the proposed mechanism can amplify both the TCPF strain and force. The experiments show that the force is amplified based on the number of loops around the diagonal axes. Although the load and temperature affect the strain amplification, the experiments confirm that the strain is amplified. In particular, depending on the loop number, the strain becomes 5.8 times the TCPF strain while maintaining the force level. Furthermore, changing the loop number, the strain and force are amplified 2.8 times and 2 times, respectively.
- 8 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (4) , 11094-11101
Wire-Storage Pantograph Mechanism for Strain and Force Amplification of a Twisted and Coiled Polymer Fiber
A twisted and coiled polymer fiber (TCPF) is a soft thermal actuator increasingly used in current robotics applications. When implementing TCPF in robotics applications, amplifying the TCPF strain and force is necessary to obtain the desired performance. Therefore, this study proposes a mechanism to amplify the strain and force of a TCPF. Considering the TCPF as a wire, the fixed and movable pulley mechanisms are available to amplify the TCPF strain and force, respectively. However, the amplification mechanism becomes bulky when the fixed pulleys are installed separately from the movable pulleys; thus, the TCPF utility reduces. This study focuses on two characteristics of the pantograph to design a compact amplification mechanism. The first characteristic is that the pulleys on the pantograph diagonal axes can be used as a movable pulley mechanism. The other characteristic is that the pantograph circumference can be a fixed pulley mechanism, as the circumference is always invariant. Based on these characteristics, the proposed mechanism can amplify both the TCPF strain and force. The experiments show that the force is amplified based on the number of loops around the diagonal axes. Although the load and temperature affect the strain amplification, the experiments confirm that the strain is amplified. In particular, depending on the loop number, the strain becomes 5.8 times the TCPF strain while maintaining the force level. Furthermore, changing the loop number, the strain and force are amplified 2.8 times and 2 times, respectively.
- Open Access
- 18 April 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 78, 24
On integral resonant vibration control and the negative direct feedthrough term of a piezoelectric bimorph beam
SPIE Digital Library Proceedings
- 18 April 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 78, 24
Open AccessOn integral resonant vibration control and the negative direct feedthrough term of a piezoelectric bimorph beam
SPIE Digital Library Proceedings
- 1 October 2021
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 344
Mechanism for anisotropic thermal expansion of polyamide fibers
- 1 October 2021
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 344
Mechanism for anisotropic thermal expansion of polyamide fibers
- 13 May 2021
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 30 (6) , 065023
Modeling and characterization for straight twisted polymer fiber actuators in blocked torsion: effect of radial thermal expansion
This paper discusses a new model and experimental characterization for thermal responses of straight twisted polymer fiber (TPF) actuators in blocked torsion. The proposed model is derived from combining the fiber stiffness matrix with Shafer’s model of free torsion. The derived model predicts that the blocking torque increases as the initial twist increases. Although it is not widely recognized, the tension of a straight TPF decreases as the initial torsion increases, and this paper explains this fact. The proposed model predicts the decrease in tension by using Shafer’s kinematic model that considers the effect of radial thermal expansion. Experimental characterization and model verification are performed using nylon 6 (polyamide 6) fiber samples with ten different initial twists, ranging from weak to strong. The results indicate that as the initial twist increases, the torque increases and the tension decreases. The tension fluctuates with respect to time. The experimental results show that the shear modulus increases as the initial twist increases. The predictions of the proposed model are reasonably consistent with the experimental thermal responses of straight TPFs in blocked torsion when the constants obtained by experimental characterization are used.
- 13 May 2021
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 30 (6) , 065023
Modeling and characterization for straight twisted polymer fiber actuators in blocked torsion: effect of radial thermal expansion
This paper discusses a new model and experimental characterization for thermal responses of straight twisted polymer fiber (TPF) actuators in blocked torsion. The proposed model is derived from combining the fiber stiffness matrix with Shafer’s model of free torsion. The derived model predicts that the blocking torque increases as the initial twist increases. Although it is not widely recognized, the tension of a straight TPF decreases as the initial torsion increases, and this paper explains this fact. The proposed model predicts the decrease in tension by using Shafer’s kinematic model that considers the effect of radial thermal expansion. Experimental characterization and model verification are performed using nylon 6 (polyamide 6) fiber samples with ten different initial twists, ranging from weak to strong. The results indicate that as the initial twist increases, the torque increases and the tension decreases. The tension fluctuates with respect to time. The experimental results show that the shear modulus increases as the initial twist increases. The predictions of the proposed model are reasonably consistent with the experimental thermal responses of straight TPFs in blocked torsion when the constants obtained by experimental characterization are used.
- 22 March 2021
- Published by SPIE-Intl Soc Optical Eng
- p. 33
A study on shunt damping performance, current servo response, and energy harvesting analysis for voice coil motors
SPIE Digital Library Proceedings
- 22 March 2021
- Published by SPIE-Intl Soc Optical Eng
- p. 33
A study on shunt damping performance, current servo response, and energy harvesting analysis for voice coil motors
SPIE Digital Library Proceedings
- Open Access
A Simple Dynamic Characterization Method for Thin Stacked Dielectric Elastomer Actuators by Suspending a Weight in Air and Electrical Excitation
This paper proposes a simple but effective method for characterizing dielectric elastomer actuators (DEAs), especially for thin stacked DEAs, which are promising for haptic devices but which measure the dynamic elastic modulus with great difficulty. The difficulty of the measurement of such a thin stacked DEA arises from the friction and local deformation of the surface between the DEA and a contact, as shown in this paper. In the proposed method, a DEA is vertically suspended and a weight is attached to it. The proposed method requires no contact with the surface of a DEA and uses only a weighting mass. Experimental results demonstrated the proposed method can estimate almost essential constants, such as the dynamic elastic modulus (Young’s modulus and damping time constant), the electrical constants (permittivity and resistivity), and the coefficient of electromechanical coupling, through the forced vibration induced by voltage actuation.
Open AccessA Simple Dynamic Characterization Method for Thin Stacked Dielectric Elastomer Actuators by Suspending a Weight in Air and Electrical Excitation
This paper proposes a simple but effective method for characterizing dielectric elastomer actuators (DEAs), especially for thin stacked DEAs, which are promising for haptic devices but which measure the dynamic elastic modulus with great difficulty. The difficulty of the measurement of such a thin stacked DEA arises from the friction and local deformation of the surface between the DEA and a contact, as shown in this paper. In the proposed method, a DEA is vertically suspended and a weight is attached to it. The proposed method requires no contact with the surface of a DEA and uses only a weighting mass. Experimental results demonstrated the proposed method can estimate almost essential constants, such as the dynamic elastic modulus (Young’s modulus and damping time constant), the electrical constants (permittivity and resistivity), and the coefficient of electromechanical coupling, through the forced vibration induced by voltage actuation.
- 7 October 2020
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 29 (11) , 115037
Symbolic finite element discretization and model order reduction of a multiphysics model for IPMC sensors
The multiphysics model of ionic polymer-metal composite (IPMC) sensors proposed by Zhu has a significant advantage of being able to describe the dynamic sensor response, which highly depends on humidity, by explicitly considering solvent dynamics. However, it is difficult to perform analysis and simulation because Zhu’s model is represented by complex non-linear partial differential equations. This paper describes the symbolic finite element discretization of Zhu’s model and further discusses the essential dynamics of the reduced-order model extracted from the finite element model. The obtained linear ordinary differential equations, or the state equation, can be easily implemented in simulators via common programming languages. The simulation results of an in-house simulator implemented by MATLAB code show good agreement with those of direct numerical simulation by using commercial software, COMSOL. To further simplify the model, the minimum order required for an appropriate approximation is numerically investigated by using a model order reduction technique. This paper reveals that the dynamic response of an IPMC sensor can be consequently approximated by a first-order or second-order linear time-invariant system.
- 7 October 2020
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 29 (11) , 115037
Symbolic finite element discretization and model order reduction of a multiphysics model for IPMC sensors
The multiphysics model of ionic polymer-metal composite (IPMC) sensors proposed by Zhu has a significant advantage of being able to describe the dynamic sensor response, which highly depends on humidity, by explicitly considering solvent dynamics. However, it is difficult to perform analysis and simulation because Zhu’s model is represented by complex non-linear partial differential equations. This paper describes the symbolic finite element discretization of Zhu’s model and further discusses the essential dynamics of the reduced-order model extracted from the finite element model. The obtained linear ordinary differential equations, or the state equation, can be easily implemented in simulators via common programming languages. The simulation results of an in-house simulator implemented by MATLAB code show good agreement with those of direct numerical simulation by using commercial software, COMSOL. To further simplify the model, the minimum order required for an appropriate approximation is numerically investigated by using a model order reduction technique. This paper reveals that the dynamic response of an IPMC sensor can be consequently approximated by a first-order or second-order linear time-invariant system.