Bruna Carolina Costa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bruna Carolina Costa has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Paulo Noronha Lisboa-Filho
São Paulo State University, Brazil
6 shared publications - Kamila Rosamilia Kantovitz
Faculdade São Leopoldo Mandic, Brazil
4 shared publications - Francisco Humberto Nociti
Faculdade São Leopoldo Mandic, Brazil
3 shared publications - Fatih Toptan
Department of Materials Science and Engineering Izmir Institute of Technology Izmir Turkey
2 shared publications - João Pedro Rangel-Coelho
Division of Oral Radiology, São Leopoldo Mandic, Campinas, Brazil
2 shared publications - Lucas Novaes Teixeira
Faculdade São Leopoldo Mandic, Campinas, SP, Brazil
2 shared publications
Latest Publications
- 30 October 2026
- Published by Wiley in Lubrication Science
Corrosion and Tribocorrosion Behaviour of a Ti15Zr15Mo Alloy: Preliminary Insights Into the Effects of Heat Treatment
The growing demand for titanium alloys with low elastic modulus for bone‐integrated implants has driven the development of novel β‐type alloys. This study examines the corrosion and tribocorrosion behaviours of a Ti15Zr15Mo alloy produced by arc melting, with and without heat treatment at 600°C for 6 h, benchmarked against Ti6Al4V. Corrosion behaviour was evaluated in phosphate‐buffered saline (PBS) at 37°C using potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS). Tribocorrosion tests were performed under reciprocating sliding against a 10 mm alumina ball (1 N, 1 Hz, 600 μm) in PBS, with simultaneous monitoring of open‐circuit potential (OCP) and coefficient of friction (COF). x‐Ray diffraction (XRD) showed a predominance of β phase in the Ti15Zr15Mo alloys, while Ti6Al4V exhibited a dual‐phase structure, with the as‐cast and heat‐treated Ti15Zr15Mo alloys exhibiting microhardnesses of 399 ± 2 HV 0.25 and 433 ± 3 HV 0.25 , respectively, compared to 337 ± 5 HV 0.25 for the Ti6Al4V benchmark. When benchmarked against Ti6Al4V, the Ti15Zr15Mo alloys exhibited lower passive film resistance ( R ox of 0.74 ± 0.05 MΩ cm 2 for as‐cast and 0.60 ± 0.02 MΩ cm 2 for heat treated versus 1.36 ± 0.68 MΩ cm 2 for Ti6Al4V), with heat treatment slightly further impairing the passive layer stability. Furthermore, significantly higher wear volume losses of (4.58 ± 0.46) × 10 −3 and (4.42 ± 1.44) × 10 −3 mm 3 were observed for the as‐cast and heat‐treated Ti15Zr15Mo alloys, respectively, relative to (1.41 ± 0.28) × 10 −3 mm 3 for the Ti6Al4V reference, highlighting the interplay between mechanical properties and tribocorrosion mechanisms.
- 30 October 2026
- Published by Wiley in Lubrication Science
Corrosion and Tribocorrosion Behaviour of a Ti15Zr15Mo Alloy: Preliminary Insights Into the Effects of Heat Treatment
The growing demand for titanium alloys with low elastic modulus for bone‐integrated implants has driven the development of novel β‐type alloys. This study examines the corrosion and tribocorrosion behaviours of a Ti15Zr15Mo alloy produced by arc melting, with and without heat treatment at 600°C for 6 h, benchmarked against Ti6Al4V. Corrosion behaviour was evaluated in phosphate‐buffered saline (PBS) at 37°C using potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS). Tribocorrosion tests were performed under reciprocating sliding against a 10 mm alumina ball (1 N, 1 Hz, 600 μm) in PBS, with simultaneous monitoring of open‐circuit potential (OCP) and coefficient of friction (COF). x‐Ray diffraction (XRD) showed a predominance of β phase in the Ti15Zr15Mo alloys, while Ti6Al4V exhibited a dual‐phase structure, with the as‐cast and heat‐treated Ti15Zr15Mo alloys exhibiting microhardnesses of 399 ± 2 HV 0.25 and 433 ± 3 HV 0.25 , respectively, compared to 337 ± 5 HV 0.25 for the Ti6Al4V benchmark. When benchmarked against Ti6Al4V, the Ti15Zr15Mo alloys exhibited lower passive film resistance ( R ox of 0.74 ± 0.05 MΩ cm 2 for as‐cast and 0.60 ± 0.02 MΩ cm 2 for heat treated versus 1.36 ± 0.68 MΩ cm 2 for Ti6Al4V), with heat treatment slightly further impairing the passive layer stability. Furthermore, significantly higher wear volume losses of (4.58 ± 0.46) × 10 −3 and (4.42 ± 1.44) × 10 −3 mm 3 were observed for the as‐cast and heat‐treated Ti15Zr15Mo alloys, respectively, relative to (1.41 ± 0.28) × 10 −3 mm 3 for the Ti6Al4V reference, highlighting the interplay between mechanical properties and tribocorrosion mechanisms.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Brazilian Oral Research
- Vol. 40, e002
Effect of titanium dioxide nanotubes in Ca(OH)2-based intracanal medicaments on odontoblast-like cells
This study investigated the effects of incorporating 3wt% titanium dioxide nanotubes (nTiO2) into calcium hydroxide [Ca(OH)2]-based intracanal medicament (ICM) formulations on the proliferation, viability, and mitochondrial metabolic activity of mouse dental papilla cells (MDPC-23). Five experimental groups were evaluated (n=3 per group): Cells (control), Calen, Calen + 3wt% nTiO2, Ultracal, and Ultracal + 3wt% nTiO2. Cell proliferation, viability, and mitochondrial metabolic activity were assessed using the Trypan Blue exclusion and MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] assays at 24, 48, and 72 h. Data analysis included the Shapiro–Wilk and Levene tests and generalized linear models (p<0.05). At 24 and 48 h, both Ultracal and Ultracal + 3wt% nTiO2 showed significantly higher proliferation than the Calen groups (p<0.0001). The control group (Cells) exhibited the highest viable cell counts (p<0.0005). At 72 h, Calen + 3wt% nTiO2 showed the lowest proliferation compared with both the Cells and the Ultracal groups (p0.05). Furthermore, Calen and Calen + 3 wt% nTiO2 at 24 and 48 h, as well as Calen + 3wt% nTiO2 at 72 h, demonstrated the lowest metabolic activity (p0.05). No significant intra-group differences over time were observed for the Cells or Ultracal groups (p=0.0608 and p=0.1417, respectively). Overall, the incorporation of nTiO2 did not adversely affect the biological parameters of Ca(OH)2-based ICMs assessed in this study. Further investigations are warranted to elucidate potential clinical implications.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Brazilian Oral Research
- Vol. 40, e002
Open AccessEffect of titanium dioxide nanotubes in Ca(OH)2-based intracanal medicaments on odontoblast-like cells
This study investigated the effects of incorporating 3wt% titanium dioxide nanotubes (nTiO2) into calcium hydroxide [Ca(OH)2]-based intracanal medicament (ICM) formulations on the proliferation, viability, and mitochondrial metabolic activity of mouse dental papilla cells (MDPC-23). Five experimental groups were evaluated (n=3 per group): Cells (control), Calen, Calen + 3wt% nTiO2, Ultracal, and Ultracal + 3wt% nTiO2. Cell proliferation, viability, and mitochondrial metabolic activity were assessed using the Trypan Blue exclusion and MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] assays at 24, 48, and 72 h. Data analysis included the Shapiro–Wilk and Levene tests and generalized linear models (p<0.05). At 24 and 48 h, both Ultracal and Ultracal + 3wt% nTiO2 showed significantly higher proliferation than the Calen groups (p<0.0001). The control group (Cells) exhibited the highest viable cell counts (p<0.0005). At 72 h, Calen + 3wt% nTiO2 showed the lowest proliferation compared with both the Cells and the Ultracal groups (p0.05). Furthermore, Calen and Calen + 3 wt% nTiO2 at 24 and 48 h, as well as Calen + 3wt% nTiO2 at 72 h, demonstrated the lowest metabolic activity (p0.05). No significant intra-group differences over time were observed for the Cells or Ultracal groups (p=0.0608 and p=0.1417, respectively). Overall, the incorporation of nTiO2 did not adversely affect the biological parameters of Ca(OH)2-based ICMs assessed in this study. Further investigations are warranted to elucidate potential clinical implications.
- 13 December 2024
- Published by Springer Nature in Odontology
- Vol. 113 (3) , 1021-1028
TiO2 nanotubes incorporated into a glaze-coating ceramic: surface roughness, color, and antibiofilm activity
This study evaluated the surface roughness, color change, and antibacterial effect of a ceramic glaze enhanced with TiO2 nanotubes (n-TiO2). n-TiO2 (0, 2, 2.5, and 5 wt%) was added to a ceramic glaze powder, applied to the surface of forty feldspathic ceramic specimens, and sintered. The surface roughness average (Ra) before glaze application (T0) and after glaze crystallization (T1) was measured using a profilometer. The colorimetric alteration was determined by CIEDE2000 (ΔE00) and CIELab (ΔEab), and the whiteness index for dentistry (ΔWID). The antibacterial effect against S. mutans and S. sanguinis was evaluated (CFU/mL). Data were analyzed by two-way repeated-measures ANOVA, followed by the Bonferroni test (α = 0.05). No differences in ΔEab and ΔE00 were observed among groups (p > 0.05), and ΔWID was only affected by 5% n-TiO2. All groups surpassed the perception thresholds of 1.8 (ΔE00) and 2.3 (ΔEab). At T0, no Ra differences were detected among groups (p > 0.05). In T1, Ra decreased (p < 005) compared to T0, but 5% n-TiO2 increased roughness compared to the control group (without n-TiO2). The incorporation of n-TiO2 into the glaze powder did not impair bacteria adhesion, and no differences in biofilm formation were found among the concentrations (p < 0.05). The ceramic covered with a glaze containing 5% n-TiO2 caused minimal interference in the color and roughness with no effect on biofilm formation.
- 13 December 2024
- Published by Springer Nature in Odontology
- Vol. 113 (3) , 1021-1028
TiO2 nanotubes incorporated into a glaze-coating ceramic: surface roughness, color, and antibiofilm activity
This study evaluated the surface roughness, color change, and antibacterial effect of a ceramic glaze enhanced with TiO2 nanotubes (n-TiO2). n-TiO2 (0, 2, 2.5, and 5 wt%) was added to a ceramic glaze powder, applied to the surface of forty feldspathic ceramic specimens, and sintered. The surface roughness average (Ra) before glaze application (T0) and after glaze crystallization (T1) was measured using a profilometer. The colorimetric alteration was determined by CIEDE2000 (ΔE00) and CIELab (ΔEab), and the whiteness index for dentistry (ΔWID). The antibacterial effect against S. mutans and S. sanguinis was evaluated (CFU/mL). Data were analyzed by two-way repeated-measures ANOVA, followed by the Bonferroni test (α = 0.05). No differences in ΔEab and ΔE00 were observed among groups (p > 0.05), and ΔWID was only affected by 5% n-TiO2. All groups surpassed the perception thresholds of 1.8 (ΔE00) and 2.3 (ΔEab). At T0, no Ra differences were detected among groups (p > 0.05). In T1, Ra decreased (p < 005) compared to T0, but 5% n-TiO2 increased roughness compared to the control group (without n-TiO2). The incorporation of n-TiO2 into the glaze powder did not impair bacteria adhesion, and no differences in biofilm formation were found among the concentrations (p < 0.05). The ceramic covered with a glaze containing 5% n-TiO2 caused minimal interference in the color and roughness with no effect on biofilm formation.
- 20 November 2024
- Published by Elsevier in Colloids and Surfaces B: Biointerfaces
- Vol. 246, 114389
Titanium dioxide nanotubes incorporated into conventional glass ionomer cement alter the biological behavior of pre-odontoblastic cells
- 20 November 2024
- Published by Elsevier in Colloids and Surfaces B: Biointerfaces
- Vol. 246, 114389
Titanium dioxide nanotubes incorporated into conventional glass ionomer cement alter the biological behavior of pre-odontoblastic cells
- 1 July 2019
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 95, 143-152
Exposure effects of endotoxin-free titanium-based wear particles to human osteoblasts
- 1 July 2019
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 95, 143-152
Exposure effects of endotoxin-free titanium-based wear particles to human osteoblasts
- 22 April 2019
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 108 (1) , 282-297
In vitroandin vivoassessment of CaP materials for bone regenerative therapy. The role of multinucleated giant cells/osteoclasts in bone regeneration
In this work, bone formation/remodeling/maturation was correlated with the presence of multinucleated giant cells (MGCs)/osteoclasts (tartrate‐resistant acid phosphatase [TRAP]‐positive cells) on the surface of beta‐tricalcium phosphate (β‐TCP), sintered deproteinized bovine bone (sDBB), and carbonated deproteinized bovine bone (cDBB) using a maxillary sinus augmentation (MSA) in aNew Zealandrabbit model. Microtomographic, histomorphometric, and immunolabeling for TRAP‐cells analyses were made at 15, 30, and 60 days after surgery. In all treatments, a faster bone formation/remodeling/maturation and TRAP‐positive cells activity occurred in the osteotomy region of the MSA than in the middle and submucosa regions. In the β‐TCP, the granules were rapidly reabsorbed by TRAP‐positive cells and replaced by bone tissue. β‐TCP enabled quick bone regeneration/remodeling and full bone and marrow restoration until 60 days, but with a significant reduction in MSA volume. In cDBB and sDBB, the quantity of TRAP‐positive cells was smaller than in β‐TCP, and these cells were associated with granule surface preparation for osteoblast‐mediated bone formation. After 30 days, more than 80% of granule surfaces were surrounded and integrated by bone tissue without signs of degradation, preserving the MSA volume. Overall, the materials tested in a standardized preclinical model led to different bone formation/remodeling/maturation within the same repair process influenced by different microenvironments and MGCs/osteoclasts. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 108B:282–297, 2020.
- 22 April 2019
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 108 (1) , 282-297
In vitroandin vivoassessment of CaP materials for bone regenerative therapy. The role of multinucleated giant cells/osteoclasts in bone regeneration
In this work, bone formation/remodeling/maturation was correlated with the presence of multinucleated giant cells (MGCs)/osteoclasts (tartrate‐resistant acid phosphatase [TRAP]‐positive cells) on the surface of beta‐tricalcium phosphate (β‐TCP), sintered deproteinized bovine bone (sDBB), and carbonated deproteinized bovine bone (cDBB) using a maxillary sinus augmentation (MSA) in aNew Zealandrabbit model. Microtomographic, histomorphometric, and immunolabeling for TRAP‐cells analyses were made at 15, 30, and 60 days after surgery. In all treatments, a faster bone formation/remodeling/maturation and TRAP‐positive cells activity occurred in the osteotomy region of the MSA than in the middle and submucosa regions. In the β‐TCP, the granules were rapidly reabsorbed by TRAP‐positive cells and replaced by bone tissue. β‐TCP enabled quick bone regeneration/remodeling and full bone and marrow restoration until 60 days, but with a significant reduction in MSA volume. In cDBB and sDBB, the quantity of TRAP‐positive cells was smaller than in β‐TCP, and these cells were associated with granule surface preparation for osteoblast‐mediated bone formation. After 30 days, more than 80% of granule surfaces were surrounded and integrated by bone tissue without signs of degradation, preserving the MSA volume. Overall, the materials tested in a standardized preclinical model led to different bone formation/remodeling/maturation within the same repair process influenced by different microenvironments and MGCs/osteoclasts. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 108B:282–297, 2020.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Journal of Applied Oral Science
- Vol. 27, e20180449
A new approach for Y-TZP surface treatment: evaluations of roughness and bond strength to resin cemen
Key words: Ceramics; Shear strength; Dental air abrasion; Confocal microscopy; Aluminum oxide
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Journal of Applied Oral Science
- Vol. 27, e20180449
Open AccessA new approach for Y-TZP surface treatment: evaluations of roughness and bond strength to resin cemen
Key words: Ceramics; Shear strength; Dental air abrasion; Confocal microscopy; Aluminum oxide