Punnathat Bordeenithikasem
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Punnathat Bordeenithikasem has a total of 145 co-authors. Here are the top co-authors by number of shared publications:
Jan Schroers
9 shared publicationsDouglas C. Hofmann
6 shared publicationsJittisa Ketkaew
4 shared publications- Douglas C. Hofmann
NASA Jet Propulsion Laboratory California Institute of Technology Pasadena CA 91109 USA
3 shared publications - Jonathan Phillip Singer
Department of Mechanical and Aerospace Engineering Rutgers, The State University of New Jersey Piscataway New Jersey USA
3 shared publications - Sebastian Alexander Kube
Department of Mechanical Engineering and Materials Science, Yale University, New Haven, USA
3 shared publications
Latest Publications
- Open Access
- 26 May 2026
- Published by Elsevier in SSRN Electronic Journal
Heat-Treatment-Driven Phase Tailoring for Enhanced Creep Resistance of Laser Powder Bed Fused Ti-6Al-4V Alloy
Laser powder bed fusion (LPBF) Ti-6Al-4V demonstrates strong potential for complex aerospace components, yet its qualification for elevated-temperature service remains uncertain due to a lack of creep data and quantitative understanding of microstructure-controlled creep-strengthening mechanisms. In this work, creep tests were performed on LPBF Ti-6Al-4V under incremental compressive loading with a broad range of stress over 400-700 °C. HIP-based post-processing routes, including HIP, HIP plus aging, and HIP plus solution treatment and aging (HIP+STA), were applied to tailor the phase constitution and lamellar morphology. Multi-scale microscopy was used to quantify α-lath dimensions, lamellar orientation dispersion, and β-phase morphology, enabling direct correlation between microstructure and creep resistance. The as-built (AB) condition exhibited distinct stress-sensitive regimes characterized by a temperature-dependent transition stress and a threshold stress of 380 MPa at 400 °C. Apparent activation energies of 202-226 kJ/mol and stress exponents spanning diffusional and dislocation-controlled regimes indicated a diffusion-assisted dislocation creep mechanism, in which the developed α/β interfacial microstructure contributed to creep resistance. AB condition exhibited minimum creep rates 2-4 orders of magnitude lower than commercially pure Ti, while post-processing further reduced the creep rates. The lowest creep rate was achieved after HIP+STA, owing to stabilized and preferentially aligned α lamellae and strengthened Widmanstätten α/β lamellar architectures. Load-transfer-modified power-law model incorporating threshold stress quantitatively captured the microstructure-enabled stress transferring. These results establish a mechanistic-based guidance for post-processing design to improve the elevated-temperature creep resistance of LPBF Ti-6Al-4V.
- 26 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessHeat-Treatment-Driven Phase Tailoring for Enhanced Creep Resistance of Laser Powder Bed Fused Ti-6Al-4V Alloy
Laser powder bed fusion (LPBF) Ti-6Al-4V demonstrates strong potential for complex aerospace components, yet its qualification for elevated-temperature service remains uncertain due to a lack of creep data and quantitative understanding of microstructure-controlled creep-strengthening mechanisms. In this work, creep tests were performed on LPBF Ti-6Al-4V under incremental compressive loading with a broad range of stress over 400-700 °C. HIP-based post-processing routes, including HIP, HIP plus aging, and HIP plus solution treatment and aging (HIP+STA), were applied to tailor the phase constitution and lamellar morphology. Multi-scale microscopy was used to quantify α-lath dimensions, lamellar orientation dispersion, and β-phase morphology, enabling direct correlation between microstructure and creep resistance. The as-built (AB) condition exhibited distinct stress-sensitive regimes characterized by a temperature-dependent transition stress and a threshold stress of 380 MPa at 400 °C. Apparent activation energies of 202-226 kJ/mol and stress exponents spanning diffusional and dislocation-controlled regimes indicated a diffusion-assisted dislocation creep mechanism, in which the developed α/β interfacial microstructure contributed to creep resistance. AB condition exhibited minimum creep rates 2-4 orders of magnitude lower than commercially pure Ti, while post-processing further reduced the creep rates. The lowest creep rate was achieved after HIP+STA, owing to stabilized and preferentially aligned α lamellae and strengthened Widmanstätten α/β lamellar architectures. Load-transfer-modified power-law model incorporating threshold stress quantitatively captured the microstructure-enabled stress transferring. These results establish a mechanistic-based guidance for post-processing design to improve the elevated-temperature creep resistance of LPBF Ti-6Al-4V.
- 27 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (18) , 20753-20771
Effect of Heat Treatment on Tensile and Fatigue Properties of Ti6Al4V Fabricated via Laser Powder Bed Fusion with Reused Powder Feedstock
- 27 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (18) , 20753-20771
Effect of Heat Treatment on Tensile and Fatigue Properties of Ti6Al4V Fabricated via Laser Powder Bed Fusion with Reused Powder Feedstock
- 27 November 2024
- Published by Elsevier in Applied Materials Today
- Vol. 42
Non-destructive evaluation of bulk metallic glass components using resonance ultrasound spectroscopy
- 27 November 2024
- Published by Elsevier in Applied Materials Today
- Vol. 42
Non-destructive evaluation of bulk metallic glass components using resonance ultrasound spectroscopy
- 22 November 2024
- Published by Elsevier in Materialia
- Vol. 38
Effect of thermal history on performance of bulk metallic glass spacecraft components
- 22 November 2024
- Published by Elsevier in Materialia
- Vol. 38
Effect of thermal history on performance of bulk metallic glass spacecraft components
- 20 March 2024
- Published by Elsevier in Acta Astronautica
- Vol. 219, 399-407
Miniaturized bulk metallic glass gripping structures for robotic mobility platforms
- 20 March 2024
- Published by Elsevier in Acta Astronautica
- Vol. 219, 399-407
Miniaturized bulk metallic glass gripping structures for robotic mobility platforms
- 1 December 2020
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 145
Compliant morphing structures from twisted bulk metallic glass ribbons
- 1 December 2020
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 145
Compliant morphing structures from twisted bulk metallic glass ribbons
- 1 August 2020
- Published by Elsevier in Materialia
- Vol. 12
Effect of chemical composition on the fracture toughness of bulk metallic glasses
- 1 August 2020
- Published by Elsevier in Materialia
- Vol. 12
Effect of chemical composition on the fracture toughness of bulk metallic glasses
- 20 July 2020
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (12)
Measuring Demisability of Bulk Metallic Glasses for Potential Satellite Applications through Ablation Experiments
Bulk metallic glasses (BMGs) exhibit attractive properties for spacecraft applications. When low Earth‐orbiting satellites reenter the atmosphere at end of mission, a measure to mitigate the generation of space debris, operators must limit the number of satellite components that reach the ground to ensure public safety. Inductively coupled plasma using an argon/air mixture to simulate reentry conditions is used to study ablation of BMG and conventional spacecraft alloys. Differential scanning calorimetry is used to determine the thermal properties of the alloys. BMGs are shown to ablate similarly to aluminum alloys (Al7075) and dramatically faster than titanium alloys (Ti‐6Al‐4V).
- 20 July 2020
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (12)
Measuring Demisability of Bulk Metallic Glasses for Potential Satellite Applications through Ablation Experiments
Bulk metallic glasses (BMGs) exhibit attractive properties for spacecraft applications. When low Earth‐orbiting satellites reenter the atmosphere at end of mission, a measure to mitigate the generation of space debris, operators must limit the number of satellite components that reach the ground to ensure public safety. Inductively coupled plasma using an argon/air mixture to simulate reentry conditions is used to study ablation of BMG and conventional spacecraft alloys. Differential scanning calorimetry is used to determine the thermal properties of the alloys. BMGs are shown to ablate similarly to aluminum alloys (Al7075) and dramatically faster than titanium alloys (Ti‐6Al‐4V).
- Top Cited Papers
- 13 April 2020
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 834
Welding and additive manufacturing with nanoparticle-enhanced aluminum 7075 wire
- 13 April 2020
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 834
Top Cited PapersWelding and additive manufacturing with nanoparticle-enhanced aluminum 7075 wire