Tianlu Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tianlu Xu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Chunling Zhang
Jilin University
3 shared publications - Lijie Qu
School of Advanced Materials and Future Technology Beijing Technology and Business University Beijing China
3 shared publications - Xueyan Dai
Key Laboratory of Automobile Materials
3 shared publications - Peihong Li
Key Laboratory of Automobile Materials
2 shared publications Yanlong Sui
Key Laboratory of Automobile Materials
2 shared publicationsJinjia Gu
Jiangsu Oseaguard Building Materials & Technology Development Co., Ltd, Nanjing 210000, P. R. China
1 shared publication
Latest Publications
- 18 March 2019
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 43 (16) , 6136-6145
Fabrication of polysiloxane foam with a pendent phenyl group for improved thermal insulation capacity and thermal stability
A phenyl group was introduced into the polymeric network of polysiloxane foam for the improvement of its thermal insulation capacity and thermal stability. Phenyl-containing polysiloxane was prepared via ring-opening polymerization, and phenyl-containing polysiloxane foam was fabricated through simultaneous foaming and crosslinking reactions. With increasing phenyl content, the thermal conductivity of the polysiloxane foam decreased from 0.093 W m−1 K−1 to 0.079 W m−1 K−1. When the phenyl content was 6.15 mol%, the average cell diameter decreased from 384 μm to 165 μm and the cell density increased from 0.58 × 108 cells per cm3 to 4.67 × 108 cells per cm3. When the phenyl content was 8.5 mol%, the cell morphology became imperfect and the average cell diameter and cell density reached 259 μm and 1.29 × 108 cells per cm3, respectively. TGA results revealed the improved thermal stability of the polysiloxane foam. The TGA curves under nitrogen and air conditions could be divided into three stages. Under nitrogen conditions, the mass loss of the maximum decomposition stage decreased and the residue at 800 °C slightly increased. Under air conditions, the maximum decomposition temperatures of the three stages increased. The compressive strength and specific compressive strength were measured and showed a downward trend.
- 18 March 2019
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 43 (16) , 6136-6145
Fabrication of polysiloxane foam with a pendent phenyl group for improved thermal insulation capacity and thermal stability
A phenyl group was introduced into the polymeric network of polysiloxane foam for the improvement of its thermal insulation capacity and thermal stability. Phenyl-containing polysiloxane was prepared via ring-opening polymerization, and phenyl-containing polysiloxane foam was fabricated through simultaneous foaming and crosslinking reactions. With increasing phenyl content, the thermal conductivity of the polysiloxane foam decreased from 0.093 W m−1 K−1 to 0.079 W m−1 K−1. When the phenyl content was 6.15 mol%, the average cell diameter decreased from 384 μm to 165 μm and the cell density increased from 0.58 × 108 cells per cm3 to 4.67 × 108 cells per cm3. When the phenyl content was 8.5 mol%, the cell morphology became imperfect and the average cell diameter and cell density reached 259 μm and 1.29 × 108 cells per cm3, respectively. TGA results revealed the improved thermal stability of the polysiloxane foam. The TGA curves under nitrogen and air conditions could be divided into three stages. Under nitrogen conditions, the mass loss of the maximum decomposition stage decreased and the residue at 800 °C slightly increased. Under air conditions, the maximum decomposition temperatures of the three stages increased. The compressive strength and specific compressive strength were measured and showed a downward trend.
- Open Access
- 23 August 2018
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 8 (52) , 29816-29829
Improved thermal properties of epoxy resin modified with polymethyl methacrylate-microencapsulated phosphorus-nitrogen-containing flame retardant
Epoxy resin composites with improved thermal resistance and flame retardancy were fabricated based on P(H) microcapsules.
- 23 August 2018
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 8 (52) , 29816-29829
Open AccessImproved thermal properties of epoxy resin modified with polymethyl methacrylate-microencapsulated phosphorus-nitrogen-containing flame retardant
Epoxy resin composites with improved thermal resistance and flame retardancy were fabricated based on P(H) microcapsules.
- 13 July 2018
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 42 (16) , 13873-13883
Preparation of dual-functionalized graphene oxide for the improvement of the thermal stability and flame-retardant properties of polysiloxane foam
Polysiloxane foam (PSF) is a foam material with outstanding performance. However, the limiting oxygen index (LOI) of pure PSF is only 22.0 vol%, which can be attributed to combustible materials. In this work, graphene oxide (GO) was functionalized with hexachlorocyclotriphosphazene (HCCP) and 3-aminopropyltriethoxy-silane (APTS). The introduction of the functionalized GO into the PSF matrix has significantly improved the dispersion and flame-retardant properties of the final PSF composite. The char residue of PSF with 1.0 wt% functionalized GO content is 43.04%, which is considerably higher than that of the pure PSF (23.18%). Furthermore, the Tmax of PSF with 5.0 wt% functionalized GO content has increased from 585.9 °C to 668.8 °C. The results of the cone calorimetry test indicate that modification with functionalized GO prolongs the combustion of PSF composites. The LOI value of PSF with 5.0 wt% functionalized GO content has increased from 22.0% to 27.6%. In addition, the peak heat release rate, total heat release, and total smoke production of PSF with 5.0 wt% functionalized GO content were decreased by 49.2%, 14.5%, and 62.2% relative to those of pure PSF. These results can be ascribed to the barrier effect of GO, the condensed-phase and gas-phase mechanisms of HCCP, and the bonding effect of APTS.
- 13 July 2018
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 42 (16) , 13873-13883
Preparation of dual-functionalized graphene oxide for the improvement of the thermal stability and flame-retardant properties of polysiloxane foam
Polysiloxane foam (PSF) is a foam material with outstanding performance. However, the limiting oxygen index (LOI) of pure PSF is only 22.0 vol%, which can be attributed to combustible materials. In this work, graphene oxide (GO) was functionalized with hexachlorocyclotriphosphazene (HCCP) and 3-aminopropyltriethoxy-silane (APTS). The introduction of the functionalized GO into the PSF matrix has significantly improved the dispersion and flame-retardant properties of the final PSF composite. The char residue of PSF with 1.0 wt% functionalized GO content is 43.04%, which is considerably higher than that of the pure PSF (23.18%). Furthermore, the Tmax of PSF with 5.0 wt% functionalized GO content has increased from 585.9 °C to 668.8 °C. The results of the cone calorimetry test indicate that modification with functionalized GO prolongs the combustion of PSF composites. The LOI value of PSF with 5.0 wt% functionalized GO content has increased from 22.0% to 27.6%. In addition, the peak heat release rate, total heat release, and total smoke production of PSF with 5.0 wt% functionalized GO content were decreased by 49.2%, 14.5%, and 62.2% relative to those of pure PSF. These results can be ascribed to the barrier effect of GO, the condensed-phase and gas-phase mechanisms of HCCP, and the bonding effect of APTS.