Mehdi Kochat
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mehdi Kochat has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Venkat Selvamanickam
University of Houston
6 shared publications - Eduard Galstyan
Department of Mechanical Engineering, Advanced Manufacturing Institute and Texas Center for Superconductivity, University of Houston, Houston, TX, USA
5 shared publications - Goran Majkic
Department of Mechanical Engineering, Advanced Manufacturing Institute and Texas Center for Superconductivity, University of Houston, Houston, TX, USA
5 shared publications Dmytro Abraimov
ASC, National High Magnetic Field Laboratory, 1800 E. Paul Dirac Dr., Tallahassee, Florida 32306-4005, USA, Tallahassee, Florida, 32310, UNITED STATES
3 shared publications- Jan Jaroszynski
Florida State University
3 shared publications Chirag Goel
Department of Mechanical Engineering, Advanced Manufacturing Institute and Texas Center for Superconductivity, University of Houston, Houston, TX, USA
2 shared publications
Latest Publications
- 18 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (5) , 1-5
Growth of High-Performance 4-5μm Thick Film REBCO Tapes Doped With Hafnium Using Advanced MOCVD
Advanced metal organic chemical vapor deposition technique (A-MOCVD) was used to grow 4-5 μm thick REBa 2 Cu 3 O 7-δ (REBCO, RE = rare earth) films, doped with 5% and 15% Hf. Thick REBCO films doped with 5% Hf exhibit self-field critical current density (J c ) over 1.8 MA/cm 2 at 77 K and 3 MA/cm 2 at 65 K, 1.5 T. Increasing the Hf content to 15% resulted in J c above 9 MA/cm 2 at 20 K, 9 T. The effect of (Ba+Hf)/Cu content in Hf-added (5 and 15 mol.%) REBCO films on the critical current density at 77 K, 0 T, c-axis lattice parameter and out-of- plane texture has been studied. In addition to growth of thick film REBCO tapes with superior performance, the A-MOCVD reactor has been used to quadruple the precursor-to-film conversion efficiency above 45%. This achievement has a first order impact in lowering the cost of REBCO tapes made by A-MOCVD.
- 18 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (5) , 1-5
Growth of High-Performance 4-5μm Thick Film REBCO Tapes Doped With Hafnium Using Advanced MOCVD
Advanced metal organic chemical vapor deposition technique (A-MOCVD) was used to grow 4-5 μm thick REBa 2 Cu 3 O 7-δ (REBCO, RE = rare earth) films, doped with 5% and 15% Hf. Thick REBCO films doped with 5% Hf exhibit self-field critical current density (J c ) over 1.8 MA/cm 2 at 77 K and 3 MA/cm 2 at 65 K, 1.5 T. Increasing the Hf content to 15% resulted in J c above 9 MA/cm 2 at 20 K, 9 T. The effect of (Ba+Hf)/Cu content in Hf-added (5 and 15 mol.%) REBCO films on the critical current density at 77 K, 0 T, c-axis lattice parameter and out-of- plane texture has been studied. In addition to growth of thick film REBCO tapes with superior performance, the A-MOCVD reactor has been used to quadruple the precursor-to-film conversion efficiency above 45%. This achievement has a first order impact in lowering the cost of REBCO tapes made by A-MOCVD.
- 12 June 2020
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 33 (7) , 07LT03
In-field critical current performance of 4.0 μ m thick film REBCO conductor with Hf addition at 4.2 K and fields up to 31.2 T
We present results on the in-field critical current ( I c ) performance of 4.0 μ m thick REBCO film with 15% Hf addition with fields up to 31.2 T and field orientations in the B║ab plane and B║c axis. Unlike the behavior at B║c, the critical current at B║ab is only very weakly dependent on field, decreasing from self-field to 31.2 T by only 22%, i.e. from the self-field value of ∼7700 A/4 mm width to ∼6300 and 5812 A/4 mm width at 14 and 30 T, respectively. These values are remarkably 3 and 5.7x higher than the corresponding critical currents at B║c. The in-field behavior of the present 15% Hf sample at field orientation B║c axis is nearly identical to the previously reported record values found in 4.3 and 4.6 μ m thick 15% Zr samples in terms of critical current density. In contrast to the pinning force behavior in the B║c orientation, which saturates to a constant value of 1.7 TN m −3 above ∼5–6 T, the pinning force in the B║ab orientation increases near-linearly, reaching a remarkable value of over 11.5 TN m −3 at 31.2 T. These results demonstrate the potential of thick REBCO conductors at 4.2 K for high field and energy density applications, in particular where the magnetic field is contained near the ab-plane.
- 12 June 2020
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 33 (7) , 07LT03
In-field critical current performance of 4.0 μ m thick film REBCO conductor with Hf addition at 4.2 K and fields up to 31.2 T
We present results on the in-field critical current ( I c ) performance of 4.0 μ m thick REBCO film with 15% Hf addition with fields up to 31.2 T and field orientations in the B║ab plane and B║c axis. Unlike the behavior at B║c, the critical current at B║ab is only very weakly dependent on field, decreasing from self-field to 31.2 T by only 22%, i.e. from the self-field value of ∼7700 A/4 mm width to ∼6300 and 5812 A/4 mm width at 14 and 30 T, respectively. These values are remarkably 3 and 5.7x higher than the corresponding critical currents at B║c. The in-field behavior of the present 15% Hf sample at field orientation B║c axis is nearly identical to the previously reported record values found in 4.3 and 4.6 μ m thick 15% Zr samples in terms of critical current density. In contrast to the pinning force behavior in the B║c orientation, which saturates to a constant value of 1.7 TN m −3 above ∼5–6 T, the pinning force in the B║ab orientation increases near-linearly, reaching a remarkable value of over 11.5 TN m −3 at 31.2 T. These results demonstrate the potential of thick REBCO conductors at 4.2 K for high field and energy density applications, in particular where the magnetic field is contained near the ab-plane.
- 3 June 2020
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 33 (7) , 074007
In-field critical current and pinning mechanisms at 4.2 K of Zr-added REBCO coated conductors
The critical current and pinning mechanisms at 4.2 K have been studied over a magnetic field range of 0–14 T for Zr-added (0, 5 and 15 mol.%) REBa 2 Cu 3 O 7-x (REBCO and RE = rare earth) coated conductors fabricated by advanced metal organic chemical vapor deposition (A-MOCVD). It is found that the (Ba + Zr)/Cu content in Zr-added (5 and 15 mol.%) REBCO affects the critical current at 77 K, 0 T as well as density, continuity and shape of BaZrO 3 (BZO) self-assembled nanocolumns and RE 2 O 3 in-plane precipitates that significantly enhance the pinning force density Fp ( H ) as well as isotropic pinning landscape at 4.2 K. In addition to bell-shape dependence of critical current density, J c , at 4.2 K with (Ba + Zr)/Cu content we observed an unusual Fp ( H ) behavior correlated to particular type of pinning centers, morphology and distribution that have been revealed by TEM microstructure analysis. By fitting the Dew–Hughes equation of the pinning force density Fp ( H ) at 4.2 K we extract the scaling behaviors of the Fp ( H ) associated with the competition of pinning mechanisms driven by vertically-aligned BZO nanorods and in-plane RE 2 O 3 pinning defects. This result sheds light on approaches towards interactive control of strong and isotropic pinning centers in Zr-added REBa 2 Cu 3 O 7-x (REBCO and RE = rare earth) coated conductors, and especially understanding the correlation between microstructural characteristics and vortex pinning mechanisms at 4.2 K in high magnetic fields.
- 3 June 2020
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 33 (7) , 074007
In-field critical current and pinning mechanisms at 4.2 K of Zr-added REBCO coated conductors
The critical current and pinning mechanisms at 4.2 K have been studied over a magnetic field range of 0–14 T for Zr-added (0, 5 and 15 mol.%) REBa 2 Cu 3 O 7-x (REBCO and RE = rare earth) coated conductors fabricated by advanced metal organic chemical vapor deposition (A-MOCVD). It is found that the (Ba + Zr)/Cu content in Zr-added (5 and 15 mol.%) REBCO affects the critical current at 77 K, 0 T as well as density, continuity and shape of BaZrO 3 (BZO) self-assembled nanocolumns and RE 2 O 3 in-plane precipitates that significantly enhance the pinning force density Fp ( H ) as well as isotropic pinning landscape at 4.2 K. In addition to bell-shape dependence of critical current density, J c , at 4.2 K with (Ba + Zr)/Cu content we observed an unusual Fp ( H ) behavior correlated to particular type of pinning centers, morphology and distribution that have been revealed by TEM microstructure analysis. By fitting the Dew–Hughes equation of the pinning force density Fp ( H ) at 4.2 K we extract the scaling behaviors of the Fp ( H ) associated with the competition of pinning mechanisms driven by vertically-aligned BZO nanorods and in-plane RE 2 O 3 pinning defects. This result sheds light on approaches towards interactive control of strong and isotropic pinning centers in Zr-added REBa 2 Cu 3 O 7-x (REBCO and RE = rare earth) coated conductors, and especially understanding the correlation between microstructural characteristics and vortex pinning mechanisms at 4.2 K in high magnetic fields.
- 19 March 2020
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 33 (5) , 055005
Enhancement of the electromagnetic properties of fully-processed REBCO tapes by high-temperature tensile-creep deformation
We present improvement in the in-field transport critical current ( I c ) of Zr-doped RE-Ba-Cu-O (REBCO, RE = rare earth) tapes to remarkable levels by post-deposition tensile-creep deformation at 580 °C. The deformed samples show up to three times higher I c than a reference sample at 77 K, 1 T when the magnetic field is parallel to the ab-plane. This enhancement in the in-field I c is attributed to an increase in the density of ab-plane stacking faults that are formed by high-temperature deformation.
- 19 March 2020
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 33 (5) , 055005
Enhancement of the electromagnetic properties of fully-processed REBCO tapes by high-temperature tensile-creep deformation
We present improvement in the in-field transport critical current ( I c ) of Zr-doped RE-Ba-Cu-O (REBCO, RE = rare earth) tapes to remarkable levels by post-deposition tensile-creep deformation at 580 °C. The deformed samples show up to three times higher I c than a reference sample at 77 K, 1 T when the magnetic field is parallel to the ab-plane. This enhancement in the in-field I c is attributed to an increase in the density of ab-plane stacking faults that are formed by high-temperature deformation.
- 20 August 2019
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 32 (10) , 10LT01
Next-generation highly flexible round REBCO STAR wires with over 580 A mm −2 at 4.2 K, 20 T for future compact magnets
We report the latest developments of next-generation flexible round RE–Ba–Cu–O (REBCO, RE = rare earth) wire, driven by the needs of compact accelerator magnets requiring round isotropic wire with an engineering current density ( J e ) of 600 A mm −2 at 4.2 K, 20 T at a bend radius of 15 mm. We have developed a Symmetric Tape Round (STAR) REBCO wire using multiple layers of REBCO tapes specifically developed for this architecture, featuring a mechanically symmetric geometry with a 10–18 μ m thick substrate wherein the superconductor film is positioned near the tape’s neutral plane for superior bend strain tolerance. Furthermore, each layer of REBCO tape is individually optimized for maximum bend strain tolerance. These ultra-thin substrate REBCO symmetric tapes enabled us to fabricate next-generation isotropic round wires of just 1.3 mm diameter and a critical current equivalent to commercial 12 mm wide REBCO tapes. The in-field performance of STAR wires of several configurations has been tested at National High Magnetic Field Laboratory to identify the most suitable architecture to meet the needs of high-field compact accelerators. At a bend radius of 15 mm, a six-layer STAR wire exhibits critical current of 778 A at 4.2 K in 20 T background field, which equals J e of 586.4 A mm −2 at a Lorentz force ( F L ) of 15.5 kN m −1 which is the highest reported J e value for REBCO wire in round geometry at this magnetic field. Similarly, a 12-layer STAR wire shows an I c of 1156 A at 31.2 T, 4.2 K which corresponds to a Lorentz force of 36 kN m −1 . Multiple tests of STAR wires at high magnetic field confirm a I c . This level of reproducibility of the high performance of STAR wire in high magnetic fields at 4.2 K and small bend radius underscores the potential of STAR REBCO wire for use in compact accelerator magnet and related applications.
- 20 August 2019
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 32 (10) , 10LT01
Next-generation highly flexible round REBCO STAR wires with over 580 A mm −2 at 4.2 K, 20 T for future compact magnets
We report the latest developments of next-generation flexible round RE–Ba–Cu–O (REBCO, RE = rare earth) wire, driven by the needs of compact accelerator magnets requiring round isotropic wire with an engineering current density ( J e ) of 600 A mm −2 at 4.2 K, 20 T at a bend radius of 15 mm. We have developed a Symmetric Tape Round (STAR) REBCO wire using multiple layers of REBCO tapes specifically developed for this architecture, featuring a mechanically symmetric geometry with a 10–18 μ m thick substrate wherein the superconductor film is positioned near the tape’s neutral plane for superior bend strain tolerance. Furthermore, each layer of REBCO tape is individually optimized for maximum bend strain tolerance. These ultra-thin substrate REBCO symmetric tapes enabled us to fabricate next-generation isotropic round wires of just 1.3 mm diameter and a critical current equivalent to commercial 12 mm wide REBCO tapes. The in-field performance of STAR wires of several configurations has been tested at National High Magnetic Field Laboratory to identify the most suitable architecture to meet the needs of high-field compact accelerators. At a bend radius of 15 mm, a six-layer STAR wire exhibits critical current of 778 A at 4.2 K in 20 T background field, which equals J e of 586.4 A mm −2 at a Lorentz force ( F L ) of 15.5 kN m −1 which is the highest reported J e value for REBCO wire in round geometry at this magnetic field. Similarly, a 12-layer STAR wire shows an I c of 1156 A at 31.2 T, 4.2 K which corresponds to a Lorentz force of 36 kN m −1 . Multiple tests of STAR wires at high magnetic field confirm a I c . This level of reproducibility of the high performance of STAR wire in high magnetic fields at 4.2 K and small bend radius underscores the potential of STAR REBCO wire for use in compact accelerator magnet and related applications.
- 14 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-4
Electromagnetic Properties of Thick Film REBCO Tapes
RE-Ba-Cu-O (REBCO, RE=rare earth) coated conductors are characterized by an anisotropic pinning behavior in applied magnetic fields. Over the years, incorporation of $\rm BaZrO_3$ nano-columns has been an effective approach to improve the pinning force and reduce the anisotropy in these materials. In this work, the magnetic field dependence of critical current density $(J_c)$ of 4.7 μm thick films grown by advanced metal-organic chemical vapor deposition (A-MOCVD) with 5% and 15% Zr addition has been studied. At 65 K, 1.5 T, the 5% Zr-added thick films manifest a $J_c$ at H||c-axis that surpasses $\rm 3 MA/cm^2$ . Increasing the Zr content to 15% results in a plateau in $J_c$ from 0.4 to 6.5 T and enables higher values of $J_c$ at fields above 6 T at 65 K. Tapes with 15% of added Zr exhibit a lift factor in critical current density ( $J_c$ (Temperature, Applied Magnetic Field / $J_c$ (77 K, 0 T))exceeding 13 and a $J_c$ exceeding $\rm 11 MA/cm^2$ at 30 K, 3 T.- 14 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-4
Electromagnetic Properties of Thick Film REBCO Tapes
RE-Ba-Cu-O (REBCO, RE=rare earth) coated conductors are characterized by an anisotropic pinning behavior in applied magnetic fields. Over the years, incorporation of $\rm BaZrO_3$ nano-columns has been an effective approach to improve the pinning force and reduce the anisotropy in these materials. In this work, the magnetic field dependence of critical current density $(J_c)$ of 4.7 μm thick films grown by advanced metal-organic chemical vapor deposition (A-MOCVD) with 5% and 15% Zr addition has been studied. At 65 K, 1.5 T, the 5% Zr-added thick films manifest a $J_c$ at H||c-axis that surpasses $\rm 3 MA/cm^2$ . Increasing the Zr content to 15% results in a plateau in $J_c$ from 0.4 to 6.5 T and enables higher values of $J_c$ at fields above 6 T at 65 K. Tapes with 15% of added Zr exhibit a lift factor in critical current density ( $J_c$ (Temperature, Applied Magnetic Field / $J_c$ (77 K, 0 T))exceeding 13 and a $J_c$ exceeding $\rm 11 MA/cm^2$ at 30 K, 3 T.