Alejandro Mateos-Canseco
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Alejandro Mateos-Canseco has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Jean-Luc Battaglia
University Bordeaux, CNRS, Bordeaux INP, I2M, UMR 5295 1 , F-33400 Talence
4 shared publications - Andrzej Kusiak
University Bordeaux, CNRS, Bordeaux INP, I2M, UMR 5295 1 , F-33400 Talence
3 shared publications - François Villeneuve
University Grenoble Alpes, CNRS, Grenoble INP, G-SCOP, UMR 5272 3 , F-38000 Grenoble
2 shared publications - Matthieu Museau
University Grenoble Alpes, CNRS, Grenoble INP, G-SCOP, UMR 5272 3 , F-38000 Grenoble
2 shared publications - Alexandre Margueret
SIMAP - Grenoble 4 , F-38402 Saint Martin d’Hères
1 shared publication - Arturo Díaz-Ponce
CONACYT—Centro de Investigaciones en Optica, Unidad de Aguascalientes, Prol. Constitución 607, Reserva Loma Bonita, Aguascalientes 20200, Mexico
1 shared publication
Latest Publications
- 1 June 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (6)
Investigation of the porosity of parts manufactured by electron beam melting using scanning photothermal radiometry
In the context of the non-destructive testing of pieces produced through additive manufacturing, this research focuses on investigating porosity using images obtained via scanning photothermal radiometry from Ti–6Al–4V samples. Variations in the material’s porosity as a function of the electron beam melting process parameters are revealed through photothermal images. The measured thermal signature is influenced by changes in the material’s apparent thermal diffusivity, which is affected by the presence of pores within the bulk material.
- 1 June 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (6)
Investigation of the porosity of parts manufactured by electron beam melting using scanning photothermal radiometry
In the context of the non-destructive testing of pieces produced through additive manufacturing, this research focuses on investigating porosity using images obtained via scanning photothermal radiometry from Ti–6Al–4V samples. Variations in the material’s porosity as a function of the electron beam melting process parameters are revealed through photothermal images. The measured thermal signature is influenced by changes in the material’s apparent thermal diffusivity, which is affected by the presence of pores within the bulk material.
- 1 October 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (10)
Thermal characterization of vertical interface by scanning photothermal radiometry
In this work, scanning photothermal radiometry is used for imaging and to characterize a submicron crack. From the thermal images, the evolution of the crack is mapped in the space with micrometer resolution. A vertical contact interface at the steel–steel junction is used to represent a micro-crack with a thickness less than 0.5 μm. The thermal quadrupole approach is used to model the heat transfer within the semi-infinite vertical crack. Then, using the phase mapping and that calculated from the model, the estimation of both the equivalent thermal boundary resistance of the interface and the average interface thickness was done.
- 1 October 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (10)
Thermal characterization of vertical interface by scanning photothermal radiometry
In this work, scanning photothermal radiometry is used for imaging and to characterize a submicron crack. From the thermal images, the evolution of the crack is mapped in the space with micrometer resolution. A vertical contact interface at the steel–steel junction is used to represent a micro-crack with a thickness less than 0.5 μm. The thermal quadrupole approach is used to model the heat transfer within the semi-infinite vertical crack. Then, using the phase mapping and that calculated from the model, the estimation of both the equivalent thermal boundary resistance of the interface and the average interface thickness was done.
- Open Access
- 1 October 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (10)
Thermal imaging by scanning photothermal radiometry
In this work, a modulated photothermal radiometry principle is applied in a scanning configuration. This technique was developed with the aim of performing imaging and thermal characterization at the microscale and exploring characteristic times lower than those accessible by infrared thermography. The use of a heat source smaller than the measurement area provides high sensitivity to in-plane heat diffusion. Application to quantitative thermal characterization of advanced micro-structured materials is demonstrated.
- 1 October 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (10)
Open AccessThermal imaging by scanning photothermal radiometry
In this work, a modulated photothermal radiometry principle is applied in a scanning configuration. This technique was developed with the aim of performing imaging and thermal characterization at the microscale and exploring characteristic times lower than those accessible by infrared thermography. The use of a heat source smaller than the measurement area provides high sensitivity to in-plane heat diffusion. Application to quantitative thermal characterization of advanced micro-structured materials is demonstrated.
- Open Access
Time-Resolved Temperature Map Prediction of Concentration Photovoltaics Systems by Means of Coupled Ray Tracing Flux Analysis and Thermal Quadrupoles Modelling
A transient 3D thermal model based on the thermal quadrupole method, coupled to ray tracing analysis, is presented. This methodology can predict transient temperature maps under any time-fluctuating irradiance flux—either synthetic or experimental—providing a useful tool for the design and parametric optimization of concentration photovoltaics systems. Analytic simulations of a concentration photovoltaics system thermal response and assessment of in-plane thermal gradients induced by fast tracking point perturbations, like those induced by wind, are provided and discussed for the first time. Computation times for time-resolved temperature maps can be as short as 9 s for a full month of system operation, with stimuli inspired by real data. Such information could pave the way for more accurate studies of cell reliability under any set of worldwide irradiance conditions.
Open AccessTime-Resolved Temperature Map Prediction of Concentration Photovoltaics Systems by Means of Coupled Ray Tracing Flux Analysis and Thermal Quadrupoles Modelling
A transient 3D thermal model based on the thermal quadrupole method, coupled to ray tracing analysis, is presented. This methodology can predict transient temperature maps under any time-fluctuating irradiance flux—either synthetic or experimental—providing a useful tool for the design and parametric optimization of concentration photovoltaics systems. Analytic simulations of a concentration photovoltaics system thermal response and assessment of in-plane thermal gradients induced by fast tracking point perturbations, like those induced by wind, are provided and discussed for the first time. Computation times for time-resolved temperature maps can be as short as 9 s for a full month of system operation, with stimuli inspired by real data. Such information could pave the way for more accurate studies of cell reliability under any set of worldwide irradiance conditions.