Hülya Durmuş
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hülya Durmuş has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Nilay Çömez
Ege Universitesi
20 shared publications - Canser Gül
Manisa Celal Bayar Üniversitesi, Mühendislik Fakültesi, Metalurji ve Malzeme Mühendisliği Bölümü
14 shared publications - Melis Yurddaskal
Department of Mechanical Engineering, Ege University, Izmir, Turkey
5 shared publications Cevdet Meriç
Material Engineering, Fatih University Engineering Faculty, Istanbul, Turkey
4 shared publications- Ahmet Meyveci
Karabuk University
3 shared publications - Fatma Gizem Çakir
Manisa Celal Bayar Üniversitesi, Mühendislik Fakültesi, Metalurji ve Malzeme Mühendisliği Bölümü
3 shared publications
Latest Publications
- 29 June 2026
- Published by Isparta Uygulamali Bilimler Universitesi in Türk Bilim ve Mühendislik Dergisi
- Vol. 8 (1) , 1-10
Kumlama Türü ve Besleme Hızının WE43 Mg Alaşımına Uygulanan Soğuk Sprey Kaplamanın Aşınma Davranışına Etkisi
Mg ve alaşımları, özellikle otomotiv, spor ve havacılık sektörlerinde artan talep gören, hafif yapısal metallerin bir grubudur. Ancak, Mg alaşımlarının ticari kullanımını sınırlayan en büyük sorun, zayıf korozyon ve aşınma dirençleridir. Bu çalışma, WE43 Mg alaşımının aşınma ve mekanik performansını artırmak amacıyla %48-52 Ni, %13-17 Zn ve %33-37 Al2O3 karışımı toz kullanılarak 500 oC’ de gerçekleştirilen soğuk sprey kaplama ile yüzey modifikasyonunu ve besleme hızı etkisini incelemektedir. Geleneksel termal sprey yöntemlerinin aksine, soğuk sprey erime, oksitlenme ve faz değişimlerini önleyerek daha yoğun kaplamalar oluşturur. WE43 alt tabakaları, iki farklı kumlama ortamı cam boncuklar ve S110 çelik bilyeler ile ön işlemden geçirilmiş ve 3, 6 ve 9 g/dk toz besleme hızlarında kaplanmıştır. XRD analizleri, düşük ısı girişi sayesinde Ni, Zn ve Al2O3’ün yapısal bütünlüğünün korunduğunu ve ara yüzeyde istenmeyen intermetalik faz oluşumunun engellendiğini göstermiştir. Aşınma testleri, cam bilye ile üretilen numunelerde Zn miktarının aşınma hacmini önemli ölçüde azalttığını (r ≈ −0.977), S110 çelik bilye ile kumlanan numunelerde ise temas açısındaki artışın aşınma direncini kritik düzeyde iyileştirdiğini (r ≈ −0.990) göstermektedir. Bu sonuçlar, uygun yüzey hazırlığı ve kaplama bileşiminin WE43 Mg alaşımının aşınma performansını artırabileceğini göstermektedir.
- 29 June 2026
- Published by Isparta Uygulamali Bilimler Universitesi in Türk Bilim ve Mühendislik Dergisi
- Vol. 8 (1) , 1-10
Kumlama Türü ve Besleme Hızının WE43 Mg Alaşımına Uygulanan Soğuk Sprey Kaplamanın Aşınma Davranışına Etkisi
Mg ve alaşımları, özellikle otomotiv, spor ve havacılık sektörlerinde artan talep gören, hafif yapısal metallerin bir grubudur. Ancak, Mg alaşımlarının ticari kullanımını sınırlayan en büyük sorun, zayıf korozyon ve aşınma dirençleridir. Bu çalışma, WE43 Mg alaşımının aşınma ve mekanik performansını artırmak amacıyla %48-52 Ni, %13-17 Zn ve %33-37 Al2O3 karışımı toz kullanılarak 500 oC’ de gerçekleştirilen soğuk sprey kaplama ile yüzey modifikasyonunu ve besleme hızı etkisini incelemektedir. Geleneksel termal sprey yöntemlerinin aksine, soğuk sprey erime, oksitlenme ve faz değişimlerini önleyerek daha yoğun kaplamalar oluşturur. WE43 alt tabakaları, iki farklı kumlama ortamı cam boncuklar ve S110 çelik bilyeler ile ön işlemden geçirilmiş ve 3, 6 ve 9 g/dk toz besleme hızlarında kaplanmıştır. XRD analizleri, düşük ısı girişi sayesinde Ni, Zn ve Al2O3’ün yapısal bütünlüğünün korunduğunu ve ara yüzeyde istenmeyen intermetalik faz oluşumunun engellendiğini göstermiştir. Aşınma testleri, cam bilye ile üretilen numunelerde Zn miktarının aşınma hacmini önemli ölçüde azalttığını (r ≈ −0.977), S110 çelik bilye ile kumlanan numunelerde ise temas açısındaki artışın aşınma direncini kritik düzeyde iyileştirdiğini (r ≈ −0.990) göstermektedir. Bu sonuçlar, uygun yüzey hazırlığı ve kaplama bileşiminin WE43 Mg alaşımının aşınma performansını artırabileceğini göstermektedir.
- Open Access
- 29 May 2026
- Published by Springer Nature in International Journal of Metalcasting
Manufacturing and Characterization of Cast Al Wheels Made of A356 Aluminum Alloy with Varying Scrap Contents
- 29 May 2026
- Published by Springer Nature in International Journal of Metalcasting
Open AccessManufacturing and Characterization of Cast Al Wheels Made of A356 Aluminum Alloy with Varying Scrap Contents
- 20 May 2026
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 123 (4) , 411
Microstructure and mechanical properties of general structural steel parts manufactured by submerged arc - wire arc additive manufacturing (SA-WAAM)
This study examines the mechanical properties of samples produced from low-carbon steel wire conforming to TS EN ISO 14341-A standards using additive manufacturing, according to different heat inputs. The samples were produced using the submerged arc welding method at speeds of 20, 22, and 24 mm/min, with temperature monitoring and surface preparation protocols. Subsequent analyses include directional mechanical property evaluation, metallography, optical and stereo microscopy, hardness and surface roughness measurements, and dry sliding wear tests. Post-wear analyses include SEM observation of wear tracks, volume loss comparison, and 3D roughness profiling. The findings reveal a distinct relationship between heat input, welding speed, grain structure, cooling rate, and the resulting morphological and mechanical property changes; in particular, it is emphasized that finer-grained, higher-hardness structures emerge with decreasing heat input.
- 20 May 2026
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 123 (4) , 411
Microstructure and mechanical properties of general structural steel parts manufactured by submerged arc - wire arc additive manufacturing (SA-WAAM)
This study examines the mechanical properties of samples produced from low-carbon steel wire conforming to TS EN ISO 14341-A standards using additive manufacturing, according to different heat inputs. The samples were produced using the submerged arc welding method at speeds of 20, 22, and 24 mm/min, with temperature monitoring and surface preparation protocols. Subsequent analyses include directional mechanical property evaluation, metallography, optical and stereo microscopy, hardness and surface roughness measurements, and dry sliding wear tests. Post-wear analyses include SEM observation of wear tracks, volume loss comparison, and 3D roughness profiling. The findings reveal a distinct relationship between heat input, welding speed, grain structure, cooling rate, and the resulting morphological and mechanical property changes; in particular, it is emphasized that finer-grained, higher-hardness structures emerge with decreasing heat input.
- Open Access
- 20 April 2026
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 29 (4) , 1-7
Anisotropic Investigation on Morphology, Mechanical, Corrosion, and Cavitation Resistance of Aluminum Alloys Produced by Wire Arc Additive Manufacturing
The Wire Arc Additive Manufacturing (WAAM) can produce parts that closely approximate the desired geometric shape while reducing costs. Although numerous papers have been published on WAAM manufacturing of different aluminium alloys , there are few studies on the directionality of production. In the present study, WAAM was performed using Cold Metal Transfer (CMT) welding equipment was used to produce sample parts with AlSi5 welding wire. Samples of these parts were produced to determine the mechanical, corrosion and wear properties of build-up and x-y directions. The results indicate that all properties except cavitation resistance were better in the build-up direction than in the x-y direction.
- 20 April 2026
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 29 (4) , 1-7
Open AccessAnisotropic Investigation on Morphology, Mechanical, Corrosion, and Cavitation Resistance of Aluminum Alloys Produced by Wire Arc Additive Manufacturing
The Wire Arc Additive Manufacturing (WAAM) can produce parts that closely approximate the desired geometric shape while reducing costs. Although numerous papers have been published on WAAM manufacturing of different aluminium alloys , there are few studies on the directionality of production. In the present study, WAAM was performed using Cold Metal Transfer (CMT) welding equipment was used to produce sample parts with AlSi5 welding wire. Samples of these parts were produced to determine the mechanical, corrosion and wear properties of build-up and x-y directions. The results indicate that all properties except cavitation resistance were better in the build-up direction than in the x-y direction.
- 25 December 2025
- Published by Vizetek Publishing Company
Metalurji ve Malzeme Mühendisliğinde Yeni Yaklaşımlar
Malzeme bilimi ve metalurji mühendisliği, modern dünyanın teknoloji üretim kapasitesini belirleyen temel disiplinlerden biridir. Ham malzemelerin doğasından başlayarak ileri mühendislik uygulamalarına uzanan bu geniş alan; havacılık, savunma, uzay, enerji, biyomedikal, üretim teknolojileri ve yapı sektörü gibi pek çok kritik endüstride yenilikçi çözümlerin anahtarıdır. Malzeme Teknolojisi ve Tasarım Bilimlerine Yeni Yaklaşımlar, malzeme teknolojilerindeki güncel eğilimleri, deneysel araştırmaları ve teorik yaklaşımları bir araya getiren kapsamlı bir başvuru kaynağıdır. Sekiz bölümden oluşan eser; biyouyumlu metal matrisli kompozitler, kaynak teknolojilerinde kusur analizi ve kalite yönetimi, nanomalzemeler, kompozit sistemler, çimento esaslı yapı malzemeleri ile yapı akustiği tasarımı gibi alanın öne çıkan konularını disiplinler arası bir bakış açısıyla ele almaktadır. Her bölüm alanında uzman akademisyen ve araştırmacıların katkılarıyla hazırlanan bu çalışma, malzeme tasarımı, üretim süreçleri ve karakterizasyon yöntemleri arasındaki etkileşimi somut örneklerle ortaya koyarak hem teorik bilgiye hem de pratik mühendislik uygulamalarına ışık tutmaktadır. Malzeme biliminin hızla gelişen yapısını anlamak, yeni teknolojilere uyum sağlamak ve mühendislik tasarım süreçlerini güçlendirmek isteyen tüm okurlar için bu kitap hem güncel hem de yol gösterici bir kaynak niteliğindedir.
- 25 December 2025
- Published by Vizetek Publishing Company
Metalurji ve Malzeme Mühendisliğinde Yeni Yaklaşımlar
Malzeme bilimi ve metalurji mühendisliği, modern dünyanın teknoloji üretim kapasitesini belirleyen temel disiplinlerden biridir. Ham malzemelerin doğasından başlayarak ileri mühendislik uygulamalarına uzanan bu geniş alan; havacılık, savunma, uzay, enerji, biyomedikal, üretim teknolojileri ve yapı sektörü gibi pek çok kritik endüstride yenilikçi çözümlerin anahtarıdır. Malzeme Teknolojisi ve Tasarım Bilimlerine Yeni Yaklaşımlar, malzeme teknolojilerindeki güncel eğilimleri, deneysel araştırmaları ve teorik yaklaşımları bir araya getiren kapsamlı bir başvuru kaynağıdır. Sekiz bölümden oluşan eser; biyouyumlu metal matrisli kompozitler, kaynak teknolojilerinde kusur analizi ve kalite yönetimi, nanomalzemeler, kompozit sistemler, çimento esaslı yapı malzemeleri ile yapı akustiği tasarımı gibi alanın öne çıkan konularını disiplinler arası bir bakış açısıyla ele almaktadır. Her bölüm alanında uzman akademisyen ve araştırmacıların katkılarıyla hazırlanan bu çalışma, malzeme tasarımı, üretim süreçleri ve karakterizasyon yöntemleri arasındaki etkileşimi somut örneklerle ortaya koyarak hem teorik bilgiye hem de pratik mühendislik uygulamalarına ışık tutmaktadır. Malzeme biliminin hızla gelişen yapısını anlamak, yeni teknolojilere uyum sağlamak ve mühendislik tasarım süreçlerini güçlendirmek isteyen tüm okurlar için bu kitap hem güncel hem de yol gösterici bir kaynak niteliğindedir.
- Open Access
- 4 December 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (6) , 1637-1644
Alüminyum Alaşımlarına Uygulanan Alüminyum Oksit Takviyeli Alüminyum/Çinko Soğuk Sprey Kaplamaların Morfoloji ve Aşınma Dayanımına Etkisi
Alüminyum alaşımları, düşük yoğunlukları nedeniyle otomotiv bileşenlerinden mutfak gereçlerine, borulardan ambalaj malzemelerine kadar geniş bir uygulama alanına sahiptir. Yaygın kullanımına rağmen, bazı uygulamalarda aşınma dirençleri yetersiz olup, bu direncin artırılması için ısıl işlemler, alaşımlandırma ve kaplama uygulamaları gereklidir. Bu çalışmada, alüminyum alaşımlarının aşınma direncini artırmak amacıyla, ticari K-20-11 ve K-00-11 tozları ile soğuk sprey kaplamalar uygulanmıştır. Kaplamaların yüzey pürüzlülüğü, kalınlığı ve aşınma davranışları incelenmiştir. Çinko içeren tozların kullanılması, daha yüksek oranda sert partikül birikmesini sağlamış ve bu durum kaplamaların aşınma kayıplarını azaltmıştır. Al-Zn ve Al2O3 bileşik tozları daha yoğun ve homojen kaplamalar oluştururken, yalnızca Zn ve Al2O3 içeren tozların daha ince kaplamalar elde ettiği belirlenmiştir. Mikroskopi ve EDS analizleri, kaplamaların homojen dağılımını doğrulamış ve Al2O3 sert partiküllerinin mekanik özelliklere katkı sağladığını göstermiştir. Mikro-Vickers sertlik testleri, yüksek sert partikül içeriğine sahip K0 tozları ile kaplanan numunelerin daha yüksek sertlik değerlerine ulaştığını ortaya koymuştur. Ayrıca, çinkonun düşük ergime noktası, sert partiküllerin gömülmesini kolaylaştırarak daha sert kaplamalar elde edilmesini sağlamıştır.
- 4 December 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (6) , 1637-1644
Open AccessAlüminyum Alaşımlarına Uygulanan Alüminyum Oksit Takviyeli Alüminyum/Çinko Soğuk Sprey Kaplamaların Morfoloji ve Aşınma Dayanımına Etkisi
Alüminyum alaşımları, düşük yoğunlukları nedeniyle otomotiv bileşenlerinden mutfak gereçlerine, borulardan ambalaj malzemelerine kadar geniş bir uygulama alanına sahiptir. Yaygın kullanımına rağmen, bazı uygulamalarda aşınma dirençleri yetersiz olup, bu direncin artırılması için ısıl işlemler, alaşımlandırma ve kaplama uygulamaları gereklidir. Bu çalışmada, alüminyum alaşımlarının aşınma direncini artırmak amacıyla, ticari K-20-11 ve K-00-11 tozları ile soğuk sprey kaplamalar uygulanmıştır. Kaplamaların yüzey pürüzlülüğü, kalınlığı ve aşınma davranışları incelenmiştir. Çinko içeren tozların kullanılması, daha yüksek oranda sert partikül birikmesini sağlamış ve bu durum kaplamaların aşınma kayıplarını azaltmıştır. Al-Zn ve Al2O3 bileşik tozları daha yoğun ve homojen kaplamalar oluştururken, yalnızca Zn ve Al2O3 içeren tozların daha ince kaplamalar elde ettiği belirlenmiştir. Mikroskopi ve EDS analizleri, kaplamaların homojen dağılımını doğrulamış ve Al2O3 sert partiküllerinin mekanik özelliklere katkı sağladığını göstermiştir. Mikro-Vickers sertlik testleri, yüksek sert partikül içeriğine sahip K0 tozları ile kaplanan numunelerin daha yüksek sertlik değerlerine ulaştığını ortaya koymuştur. Ayrıca, çinkonun düşük ergime noktası, sert partiküllerin gömülmesini kolaylaştırarak daha sert kaplamalar elde edilmesini sağlamıştır.
- 9 September 2025
- Published by Izmir UOD
- p. 420-425
Research on Methods to Enhance the Wear Properties of 41CrMo4 Steel
The material selection process in engineering design is complex due to the presence of numerous materials and the necessity to evaluate their various properties together. Issues commonly encountered in the manufacturing of agricultural machinery, such as wear, cracks, and sudden breakage, highlight the vital importance of appropriate material selection. In this context, the 41CrMo4 alloy is preferred in the manufacturing of parts that carry high loads, as it offers significant advantages across many sectors due to its high strength. The high-strength properties of this alloy enable its use in the production of heavy machinery, such as transport systems, concrete machines, and construction equipment. Additionally, it is favoured for pipelines and other equipment due to its resistance to impact and wear. This alloy, which enhances wear resistance thanks to its carbon and chromium content, is further strengthened through hardening and hardfacing applications. These characteristics are among the main reasons why the 41CrMo4 alloy is commonly chosen for dynamic applications. In this study, the effects of tempered and hardfacing 41CrMo4 steel on wear properties were investigated using the Dry Sand Rubber Wheel test device according to ASTM G65. Hardness measurements were taken from the surface and cross-section to determine the mechanical properties of the materials. Microstructures of the samples were conducted. As a result, it was found that the wear resistance was higher in the 41CrMo4 samples that had a hardfacing applied to their surface.
- 9 September 2025
- Published by Izmir UOD
- p. 420-425
Research on Methods to Enhance the Wear Properties of 41CrMo4 Steel
The material selection process in engineering design is complex due to the presence of numerous materials and the necessity to evaluate their various properties together. Issues commonly encountered in the manufacturing of agricultural machinery, such as wear, cracks, and sudden breakage, highlight the vital importance of appropriate material selection. In this context, the 41CrMo4 alloy is preferred in the manufacturing of parts that carry high loads, as it offers significant advantages across many sectors due to its high strength. The high-strength properties of this alloy enable its use in the production of heavy machinery, such as transport systems, concrete machines, and construction equipment. Additionally, it is favoured for pipelines and other equipment due to its resistance to impact and wear. This alloy, which enhances wear resistance thanks to its carbon and chromium content, is further strengthened through hardening and hardfacing applications. These characteristics are among the main reasons why the 41CrMo4 alloy is commonly chosen for dynamic applications. In this study, the effects of tempered and hardfacing 41CrMo4 steel on wear properties were investigated using the Dry Sand Rubber Wheel test device according to ASTM G65. Hardness measurements were taken from the surface and cross-section to determine the mechanical properties of the materials. Microstructures of the samples were conducted. As a result, it was found that the wear resistance was higher in the 41CrMo4 samples that had a hardfacing applied to their surface.
- Open Access
- 23 January 2025
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 67 (3) , 446-456
Effect of sandblasting and aging on structural and mechanical properties of Inconel 625 coated steels for marine applications
In present study, the Inconel 625 alloy was coated using TIG welding method, and the coating was subjected to sandblasting and artificial aging. The coating samples were examined by wear and corrosion tests to evaluate their performance in marine applications. The study characterized different sample groups for the purposes of coating steel samples, coating surfaces by deformation, applying aging processes, and observing the combined effects of aging and deformation. Wet-sliding wear and corrosion tests were conducted in 3.5 wt.% NaCl solution. The presence of compressive stresses resulting from sandblasting and aging led to microstructural changes, while formation of δ, γ′, γ″ phases and complex carbides contributed to increased wear and corrosion resistance. Deformation supported the precipitation of γ′, γ″ phases and carbides. Aging increased the hardness by 30 %, whereas the sandblasting process doubled up the hardness of as-deposited coating. Maximum corrosion resistance was obtained in the aged sample without applying sandblasting.
- 23 January 2025
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 67 (3) , 446-456
Open AccessEffect of sandblasting and aging on structural and mechanical properties of Inconel 625 coated steels for marine applications
In present study, the Inconel 625 alloy was coated using TIG welding method, and the coating was subjected to sandblasting and artificial aging. The coating samples were examined by wear and corrosion tests to evaluate their performance in marine applications. The study characterized different sample groups for the purposes of coating steel samples, coating surfaces by deformation, applying aging processes, and observing the combined effects of aging and deformation. Wet-sliding wear and corrosion tests were conducted in 3.5 wt.% NaCl solution. The presence of compressive stresses resulting from sandblasting and aging led to microstructural changes, while formation of δ, γ′, γ″ phases and complex carbides contributed to increased wear and corrosion resistance. Deformation supported the precipitation of γ′, γ″ phases and carbides. Aging increased the hardness by 30 %, whereas the sandblasting process doubled up the hardness of as-deposited coating. Maximum corrosion resistance was obtained in the aged sample without applying sandblasting.
- 4 October 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (6)
Wear and corrosion resistance of zinc-oxide and zirconium-oxide coated WE43 magnesium alloy
Magnesium alloy, which draws attention with its lightness and high specific strength, is frequently preferred due to its advantages. However, it is necessary to improve the wear and corrosion properties in order to develop the areas of use in the automotive, aircraft, and space industries. For this purpose, after the surface preparation of the main material WE43 Mg alloy, ZnO and ZrO2 coatings were made and characterized in this study. The surface morphology and structural and chemical properties of the samples were investigated using profilometry, contact angle tests, scanning electron microscopy, and x-ray diffraction. Corrosion tests have been carried out. In order to determine the wear performance of the samples, the wear-related volume losses were measured and the friction coefficients were compared. Layers with 2–6 μm coating thickness were obtained homogeneously on the polished and sandblasted sample surfaces. It was determined that the coating layers grew in the form of columns and did not contain capillary cracks. As a result of the study, it was observed that the ZnO-coated samples had the highest wear and corrosion resistance, and the wear and corrosion resistance of the coatings and magnesium alloy substrates improved.
- 4 October 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (6)
Wear and corrosion resistance of zinc-oxide and zirconium-oxide coated WE43 magnesium alloy
Magnesium alloy, which draws attention with its lightness and high specific strength, is frequently preferred due to its advantages. However, it is necessary to improve the wear and corrosion properties in order to develop the areas of use in the automotive, aircraft, and space industries. For this purpose, after the surface preparation of the main material WE43 Mg alloy, ZnO and ZrO2 coatings were made and characterized in this study. The surface morphology and structural and chemical properties of the samples were investigated using profilometry, contact angle tests, scanning electron microscopy, and x-ray diffraction. Corrosion tests have been carried out. In order to determine the wear performance of the samples, the wear-related volume losses were measured and the friction coefficients were compared. Layers with 2–6 μm coating thickness were obtained homogeneously on the polished and sandblasted sample surfaces. It was determined that the coating layers grew in the form of columns and did not contain capillary cracks. As a result of the study, it was observed that the ZnO-coated samples had the highest wear and corrosion resistance, and the wear and corrosion resistance of the coatings and magnesium alloy substrates improved.
- Open Access
- 19 July 2023
- Published by Academician Publishing
Temel Spinal Enstrüman Bilgisi
Türkiye’de Spinal Enstrümantasyonun Tarihi Sait NADERİ Mekanik ve Biyomekaniğin Temelleri Bozkurt Burak ÖZHAN Spinal İmplantların Elemanları Cumhur KILINÇER Lisa FERRARA Metalurji ve Alaşım Bilgisi Enver ATİK Klasik Üretim Yöntemleri Enver ATİK Katmanlı İmalat (Kİ) - Additive Manufacturing (AM) Cüneyt TEMİZ Peyker TEMİZ Cerrahide 3D Printer Destekli İmplant Üretimi ve Kaplama Yöntemleri Hasan Emre AYDIN Deniz AKKAYA Ali ARSLANTAŞ Biyouyumlu Malzemeler ve Mekanik Özellikleri Melis YURDDAŞKAL Hülya DURMUŞ Biyomalzemelerin Karakterizasyonu Hüseyin Erdem YALKIN Patoloji ve Enstruman Biyomekaniği Serdar ÇEVİK Hakan HANIMOĞLU Hakan BOZKUŞ Cerrahi Teknik - Enstruman İlişkisi Ömer AKÇALI Enstrüman, Füzyon, Psödoartroz Burak TAHMAZOĞLU Taha Şükrü KORKMAZ Murat HANCI Osteoporotik Omurga Cerrahisinde Kullanılan İmplantlar Varol AYDIN Kadir KOTİL Geçiş Bölgelerinde Enstrüman Sorunları, Yük Yoğunlaşması ve Proksimal Bileşke Sorunları Seymur NİFTALİYEV Erkan KAPTANOĞLU Spinal Enstrümantasyonda Yetmezlik Mehdi HEKİMOĞLU Ahmet Tulgar BAŞAK Ali Fahir ÖZER Enstrüman Kurgusunun Komplikasyonlarla İlişkisi Muhammed Taha ESER Süleyman Rüştü ÇAYLI Spinal İmplant Teknolojisi : Gelişmeler Cüneyt TEMİZ Peyker TEMİZ Mehmet EMİNOĞLU Ömer Emre YAĞLI Spinal Araştırma Geliştirme, Sertifikasyon ve İnovasyon Süreçleri Cüneyt TEMİZ Mehmet EMİNOĞLU Ömer Emre YAĞLI Burak TÜLÜ Spinal Cerrahide Yeni Teknolojik Gelişmeler; Teletıp, Robotik Sistemler ve Genişletilmiş Gerçeklik-Karma Gerçeklik Macit TERZİ Emre BAHİR METE Murat ZAİMOĞLU Yusuf Şükrü ÇAĞLAR Spinal Cerrahide Enstrümantasyon ile İlgili Hekim Sorumluluğu Serdar IŞIK
- 19 July 2023
- Published by Academician Publishing
Open AccessTemel Spinal Enstrüman Bilgisi
Türkiye’de Spinal Enstrümantasyonun Tarihi Sait NADERİ Mekanik ve Biyomekaniğin Temelleri Bozkurt Burak ÖZHAN Spinal İmplantların Elemanları Cumhur KILINÇER Lisa FERRARA Metalurji ve Alaşım Bilgisi Enver ATİK Klasik Üretim Yöntemleri Enver ATİK Katmanlı İmalat (Kİ) - Additive Manufacturing (AM) Cüneyt TEMİZ Peyker TEMİZ Cerrahide 3D Printer Destekli İmplant Üretimi ve Kaplama Yöntemleri Hasan Emre AYDIN Deniz AKKAYA Ali ARSLANTAŞ Biyouyumlu Malzemeler ve Mekanik Özellikleri Melis YURDDAŞKAL Hülya DURMUŞ Biyomalzemelerin Karakterizasyonu Hüseyin Erdem YALKIN Patoloji ve Enstruman Biyomekaniği Serdar ÇEVİK Hakan HANIMOĞLU Hakan BOZKUŞ Cerrahi Teknik - Enstruman İlişkisi Ömer AKÇALI Enstrüman, Füzyon, Psödoartroz Burak TAHMAZOĞLU Taha Şükrü KORKMAZ Murat HANCI Osteoporotik Omurga Cerrahisinde Kullanılan İmplantlar Varol AYDIN Kadir KOTİL Geçiş Bölgelerinde Enstrüman Sorunları, Yük Yoğunlaşması ve Proksimal Bileşke Sorunları Seymur NİFTALİYEV Erkan KAPTANOĞLU Spinal Enstrümantasyonda Yetmezlik Mehdi HEKİMOĞLU Ahmet Tulgar BAŞAK Ali Fahir ÖZER Enstrüman Kurgusunun Komplikasyonlarla İlişkisi Muhammed Taha ESER Süleyman Rüştü ÇAYLI Spinal İmplant Teknolojisi : Gelişmeler Cüneyt TEMİZ Peyker TEMİZ Mehmet EMİNOĞLU Ömer Emre YAĞLI Spinal Araştırma Geliştirme, Sertifikasyon ve İnovasyon Süreçleri Cüneyt TEMİZ Mehmet EMİNOĞLU Ömer Emre YAĞLI Burak TÜLÜ Spinal Cerrahide Yeni Teknolojik Gelişmeler; Teletıp, Robotik Sistemler ve Genişletilmiş Gerçeklik-Karma Gerçeklik Macit TERZİ Emre BAHİR METE Murat ZAİMOĞLU Yusuf Şükrü ÇAĞLAR Spinal Cerrahide Enstrümantasyon ile İlgili Hekim Sorumluluğu Serdar IŞIK