Sophie Duquesne
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sophie Duquesne has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Serge Bourbigot
Univ. Lille, CNRS, INRAE, Centrale Lille, UMR 8207 ‐ UMET ‐ Unité Matériaux et Transformations Lille France
16 shared publications - Fabienne Samyn
CNRS, INRAE, Centrale Lille, UMR 8207-UMET-Unité Matériaux et Transformations, Université de Lille, F-59000 Lille, France
5 shared publications Mathilde Casetta
Univ. Lille, CNRS, INRA, ENSCL, UMR 8207, UMET - Unité Matériaux et Transformations, F-59000, Lille, France
4 shared publications- Séverine Bellayer
Univ. Lille, CNRS, INRAE, Centrale Lille, UMR 8207 - UMET - Unité Matériaux et Transformations, F-59000, Lille, France
3 shared publications - Anthony Collin
LEMTA, Laboratoire d’Energétique et de Mécanique Théorique et Appliquée, Université de Lorraine, UMR 7563, CNRS, F-54500 Vandœuvre-lès-Nancy, France
2 shared publications - Baljinder K. Kandola
Institute for Materials Research and Innovation (IMRI), University of Greater Manchester, Deane Road, Bolton BL3 5AB, UK
2 shared publications
Latest Publications
- Open Access
Enhancing Flame Retardancy in Polypropylene Composites: A Bayesian Optimization Approach
The traditional optimization of intumescent flame-retardant polypropylene (PP) relies on large experimental campaigns that scale poorly with compositional dimensionality, limiting the systematic exploration of tradeoffs between fire performance and material economy. We present a Multi-Objective Bayesian Optimization (MOBO) workflow that couples Gaussian Process (GP) surrogates with the q-Noisy Expected Hypervolume Improvement (qNEHVI) acquisition to co-optimize two competing objectives: maximize the Limiting Oxygen Index (LOI) and minimize total flame-retardant (FR) loading (wt.%). Two practical initialization strategies, Space-Filling Design and literature-guided sampling, are benchmarked, and convergence is monitored via dominated hypervolume and uncertainty calibration. Uniform design-space coverage yields faster hypervolume growth and better-calibrated uncertainty than literature seeding. Under a 20-experiment budget, the best formulation attains an LOI = 27.0 vol.% at 22.74 wt.% FR, corresponding to an estimated 8–14% efficiency gain, defined here as LOI improvement at comparable FR loadings relative to representative baselines. The recovered APP/PER stoichiometric ratios (1.69–2.26) are consistent with established intumescence mechanisms, indicating that a data-driven search can converge to physically meaningful solutions without explicit mechanistic priors. The proposed workflow provides a sample-efficient route to navigate multi-criteria design spaces in flame-retardant PP and is transferable to polymer systems in which performance, cost, and processing constraints must be balanced and exhaustive testing is impractical.
Open AccessEnhancing Flame Retardancy in Polypropylene Composites: A Bayesian Optimization Approach
The traditional optimization of intumescent flame-retardant polypropylene (PP) relies on large experimental campaigns that scale poorly with compositional dimensionality, limiting the systematic exploration of tradeoffs between fire performance and material economy. We present a Multi-Objective Bayesian Optimization (MOBO) workflow that couples Gaussian Process (GP) surrogates with the q-Noisy Expected Hypervolume Improvement (qNEHVI) acquisition to co-optimize two competing objectives: maximize the Limiting Oxygen Index (LOI) and minimize total flame-retardant (FR) loading (wt.%). Two practical initialization strategies, Space-Filling Design and literature-guided sampling, are benchmarked, and convergence is monitored via dominated hypervolume and uncertainty calibration. Uniform design-space coverage yields faster hypervolume growth and better-calibrated uncertainty than literature seeding. Under a 20-experiment budget, the best formulation attains an LOI = 27.0 vol.% at 22.74 wt.% FR, corresponding to an estimated 8–14% efficiency gain, defined here as LOI improvement at comparable FR loadings relative to representative baselines. The recovered APP/PER stoichiometric ratios (1.69–2.26) are consistent with established intumescence mechanisms, indicating that a data-driven search can converge to physically meaningful solutions without explicit mechanistic priors. The proposed workflow provides a sample-efficient route to navigate multi-criteria design spaces in flame-retardant PP and is transferable to polymer systems in which performance, cost, and processing constraints must be balanced and exhaustive testing is impractical.
- Open Access
- 8 April 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Enhancing Flame Retardancy in Polypropylene Composites: A Bayesian Optimization Approach
This study presents a novel application of Multi-Objective Bayesian Optimization (MOBO) to enhance the formulation of flame-retardant polypropylene (PP) composites. Our goal was to optimize the chemical composition of intumescent polypropylene (PP) formulations by maximizing the Limiting Oxygen Index (LOI) and minimizing filler content. Two different initialization procedures were studied: one using a Space Filling Design and the other based on literature-based formulations. The optimization model is based on a Gaussian Process (GP), employing the parallel acquisition function qNEHVI for suggesting experiments. Our research successfully navigates the complexities of material property optimization by proposing an optimal formulation within a constrained evaluation framework. This involved five iterations of three parallel evaluations, totaling a budget of 20 points. This work underscores MOBO’s potential as a transformative tool in advanced materials science, particularly for developing high-performance flame-retardant materials.
- 8 April 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessEnhancing Flame Retardancy in Polypropylene Composites: A Bayesian Optimization Approach
This study presents a novel application of Multi-Objective Bayesian Optimization (MOBO) to enhance the formulation of flame-retardant polypropylene (PP) composites. Our goal was to optimize the chemical composition of intumescent polypropylene (PP) formulations by maximizing the Limiting Oxygen Index (LOI) and minimizing filler content. Two different initialization procedures were studied: one using a Space Filling Design and the other based on literature-based formulations. The optimization model is based on a Gaussian Process (GP), employing the parallel acquisition function qNEHVI for suggesting experiments. Our research successfully navigates the complexities of material property optimization by proposing an optimal formulation within a constrained evaluation framework. This involved five iterations of three parallel evaluations, totaling a budget of 20 points. This work underscores MOBO’s potential as a transformative tool in advanced materials science, particularly for developing high-performance flame-retardant materials.
- Open Access
- 17 June 2024
- Published by Wiley in Advanced Energy and Sustainability Research
- Vol. 5 (9)
Effect of the Nature, the Content and the Preparation Method of Zeolite‐Polymer Mixtures on the Pyrolysis of Linear Low‐Density Polyethylene
The effect of the preparation method of the mixture catalyst/polymer on the linear low‐density polyethylene (LLDPE) pyrolysis is studied by comparing the results obtained when the polymer and the catalyst (Hβ or HZSM‐5) are extruded or simply mixed in powder form. By improving the polymer/catalyst contact through extrusion, the polymer degradation took place at lower temperature. The effect of extrusion is more pronounced with Hβ compared to HZSM‐5 owing to the highest external surface of Hβ. While the yields of gas/liquid/coke do not differ with the preparation method when HZSM‐5 is used as catalyst, more significant amount of liquid phase and high production of paraffins are observed when Hβ/LLDPE mixture is extruded, according to random scission pathway reactions. The subsequent reactions are limited by the size of the pore, which impede hydrogenation reactions, producing high molecular weight molecules. Regardless of zeolite type, the micropores of the zeolite are more affected by deactivation by coke when extrusion method is used, this effect being much more important for HZSM‐5. This result is a consequence of a polymer pre‐degradation during the extrusion process in which the first cracks of the polymer at low temperature and the first pore blockages can be generated.
- 17 June 2024
- Published by Wiley in Advanced Energy and Sustainability Research
- Vol. 5 (9)
Open AccessEffect of the Nature, the Content and the Preparation Method of Zeolite‐Polymer Mixtures on the Pyrolysis of Linear Low‐Density Polyethylene
The effect of the preparation method of the mixture catalyst/polymer on the linear low‐density polyethylene (LLDPE) pyrolysis is studied by comparing the results obtained when the polymer and the catalyst (Hβ or HZSM‐5) are extruded or simply mixed in powder form. By improving the polymer/catalyst contact through extrusion, the polymer degradation took place at lower temperature. The effect of extrusion is more pronounced with Hβ compared to HZSM‐5 owing to the highest external surface of Hβ. While the yields of gas/liquid/coke do not differ with the preparation method when HZSM‐5 is used as catalyst, more significant amount of liquid phase and high production of paraffins are observed when Hβ/LLDPE mixture is extruded, according to random scission pathway reactions. The subsequent reactions are limited by the size of the pore, which impede hydrogenation reactions, producing high molecular weight molecules. Regardless of zeolite type, the micropores of the zeolite are more affected by deactivation by coke when extrusion method is used, this effect being much more important for HZSM‐5. This result is a consequence of a polymer pre‐degradation during the extrusion process in which the first cracks of the polymer at low temperature and the first pore blockages can be generated.
- Open Access
Preparation and Characterisation of UV-Curable Flame Retardant Wood Coating Containing a Phosphorus Acrylate Monomer
The application of a flame retardant coating is an effective solution to enhance the fire retardancy of wood flooring. However, finding the right balance between reducing the flame propagation and good overall coating properties while conserving wood appearance is complex. In order to answer this complex problem, transparent ultraviolet (UV)-curable flame retardant wood coatings were prepared from an acrylate oligomer, an acrylate monomer, and the addition of the tri(acryloyloxyethyl) phosphate (TAEP), a phosphorus-based monomer, at different concentrations in the formulation. The coatings’ photopolymerisation, optical transparency, hardness, water sorption and thermal stability were assessed. The fire behaviour and the adhesion of the coatings applied on the yellow birch panels were evaluated, respectively, using the cone calorimeter and pull-off tests. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) analyses were performed on the collected burnt residues to obtain a better understanding of the flame retardancy mechanism. Our study reveals that phosphorus monomer addition improved the coating adhesion and the fire performance of the coated wood without impacting the photopolymerisation. The conversion percentage remained close to 70% with the TAEP addition. The pull-off strength reached 1.12 MPa for the coating with the highest P-monomer content, a value significantly different from the non-flame retarded coating. For the same coating formulation, the peak of heat release rate decreased by 13% and the mass percentage of the residues increased by 37% compared to the reference. However, the flame-retarded coatings displayed a higher hygroscopy. The action in the condensed phase of the phosphorus flame retardant is highlighted in this study.
Open AccessPreparation and Characterisation of UV-Curable Flame Retardant Wood Coating Containing a Phosphorus Acrylate Monomer
The application of a flame retardant coating is an effective solution to enhance the fire retardancy of wood flooring. However, finding the right balance between reducing the flame propagation and good overall coating properties while conserving wood appearance is complex. In order to answer this complex problem, transparent ultraviolet (UV)-curable flame retardant wood coatings were prepared from an acrylate oligomer, an acrylate monomer, and the addition of the tri(acryloyloxyethyl) phosphate (TAEP), a phosphorus-based monomer, at different concentrations in the formulation. The coatings’ photopolymerisation, optical transparency, hardness, water sorption and thermal stability were assessed. The fire behaviour and the adhesion of the coatings applied on the yellow birch panels were evaluated, respectively, using the cone calorimeter and pull-off tests. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) analyses were performed on the collected burnt residues to obtain a better understanding of the flame retardancy mechanism. Our study reveals that phosphorus monomer addition improved the coating adhesion and the fire performance of the coated wood without impacting the photopolymerisation. The conversion percentage remained close to 70% with the TAEP addition. The pull-off strength reached 1.12 MPa for the coating with the highest P-monomer content, a value significantly different from the non-flame retarded coating. For the same coating formulation, the peak of heat release rate decreased by 13% and the mass percentage of the residues increased by 37% compared to the reference. However, the flame-retarded coatings displayed a higher hygroscopy. The action in the condensed phase of the phosphorus flame retardant is highlighted in this study.
- 1 October 2021
- Published by Elsevier in Fire Safety Journal
- Vol. 125, 103429
Small-scale single burning item test for the study of the fire behavior of building materials
- 1 October 2021
- Published by Elsevier in Fire Safety Journal
- Vol. 125, 103429
Small-scale single burning item test for the study of the fire behavior of building materials
- Open Access
Innovative Polyelectrolyte Treatment to Flame-Retard Wood
Fire protection has been a major challenge in wood construction for many years, mainly due to the high flame spread risk associated with wood flooring. Wood fire-retardancy is framed by two main axes: coating and bulk impregnation. There is a growing need for economically and environmentally friendly alternatives. The study of polyelectrolyte complexes (PECs) for wood substrates is in its infancy, but PECs’ versatility and eco-friendly character are already recognized for fabric fire-retardancy fabrics. In this study, a new approach to PEC characterization is proposed. First, PECs, which consist of polyethyleneimine and sodium phytate, were chemically and thermally characterized to select the most promising systems. Then, yellow birch (Betula alleghaniensis Britt.) was surface-impregnated under reduced pressure with the two PECs identified as the best options. Overall, wood fire-retardancy was improved with a low weight gain of 2 wt.% without increasing water uptake.
Open AccessInnovative Polyelectrolyte Treatment to Flame-Retard Wood
Fire protection has been a major challenge in wood construction for many years, mainly due to the high flame spread risk associated with wood flooring. Wood fire-retardancy is framed by two main axes: coating and bulk impregnation. There is a growing need for economically and environmentally friendly alternatives. The study of polyelectrolyte complexes (PECs) for wood substrates is in its infancy, but PECs’ versatility and eco-friendly character are already recognized for fabric fire-retardancy fabrics. In this study, a new approach to PEC characterization is proposed. First, PECs, which consist of polyethyleneimine and sodium phytate, were chemically and thermally characterized to select the most promising systems. Then, yellow birch (Betula alleghaniensis Britt.) was surface-impregnated under reduced pressure with the two PECs identified as the best options. Overall, wood fire-retardancy was improved with a low weight gain of 2 wt.% without increasing water uptake.
- 24 April 2020
- Published by Wiley in Fire and Materials
- Vol. 45 (3) , 366-378
Preparation and flame retardancy of flax fabric/polybenzoxazine laminates
Summary: Driven by the need to reduce the carbon footprint of materials, natural fibres reinforced composites are increasingly used. Today, their level of maturity allows to consider their applications in fields where high performance such as flame retardancy are required. This article compares the fire retardant properties of flax laminates based on two thermosets resins, a bio‐based polybenzoxazine and a petroleum‐based epoxy, both considered for aeronautical applications. The effect of alkaline and silane surface modifications of the fibres on the properties of the composites was investigated. The treatments of the flax were proven to allow a better impregnation of the fibres by the matrices but at the same time more defects were observed. Regarding the fire behaviour of the composites, no difference of flammability was highlighted between the treated and untreated materials. The burnthrough resistance evaluation was performed using a small‐scale aeronautical test. The better performance of the epoxy‐based composite compare to the polybenzoxazine one was shown whereas charring is favoured for polybenzoxazine. The low deformability of the char formed when polybenzoxazine decomposes leads to the formation of cracks with the subsequent failure of the test.
- 24 April 2020
- Published by Wiley in Fire and Materials
- Vol. 45 (3) , 366-378
Preparation and flame retardancy of flax fabric/polybenzoxazine laminates
Summary: Driven by the need to reduce the carbon footprint of materials, natural fibres reinforced composites are increasingly used. Today, their level of maturity allows to consider their applications in fields where high performance such as flame retardancy are required. This article compares the fire retardant properties of flax laminates based on two thermosets resins, a bio‐based polybenzoxazine and a petroleum‐based epoxy, both considered for aeronautical applications. The effect of alkaline and silane surface modifications of the fibres on the properties of the composites was investigated. The treatments of the flax were proven to allow a better impregnation of the fibres by the matrices but at the same time more defects were observed. Regarding the fire behaviour of the composites, no difference of flammability was highlighted between the treated and untreated materials. The burnthrough resistance evaluation was performed using a small‐scale aeronautical test. The better performance of the epoxy‐based composite compare to the polybenzoxazine one was shown whereas charring is favoured for polybenzoxazine. The low deformability of the char formed when polybenzoxazine decomposes leads to the formation of cracks with the subsequent failure of the test.
- 1 January 2020
- Published by Elsevier in Journal of Cleaner Production
- Vol. 242, 118527
Life cycle assessment of multi-step versus one-step coating processes using oil or bio-based resins
- 1 January 2020
- Published by Elsevier in Journal of Cleaner Production
- Vol. 242, 118527
Life cycle assessment of multi-step versus one-step coating processes using oil or bio-based resins
- Open Access
Sol–Gel Treatments to Flame Retard PA11/Flax Composites
This work investigates the efficiency of sol–gel treatments to flame retard flax fabric/PA11 composites. Different sol–gel treatments applied to the flax fabrics were prepared using TEOS in combination with phosphorus and/or nitrogen containing co-precursors (DEPTES, APTES) or additives (OP1230, OP1311). When the nitrogen and the phosphorus co-precursors were used, two coating methods were studied: a ‘one-pot’ route and a successive layer deposition method. For the “one-pot” method, the three precursors (TEOS, DEPTES, and APTES) were mixed together in the same solutions whereas for the different layers deposition method, the three different treatments were deposited on the fibers successively, first the TEOS, then a mix of TEOS/DEPTES, and finally a mix of TEOS/APTES. After deposition, the sol–gel coatings were characterized using scanning electron microscope, electron probe microanalyzer, and 29Si and 31P solid-state NMR. When only TEOS or a mix of TEOS and DEPTES is used, homogeneous coatings are obtained presenting well-condensed Si units (mainly Q units). When APTES is added, the coatings are less homogenous and agglomerates are present. A lower condensation rate of the Si network is also noticed by solid-state NMR. When additives are used in combination with TEOS, the TEOS forms a homogenous and continuous film at the surface of the fibers, but the flame retardants are not well distributed and form aggregates. The flame retardant (FR) efficiency of the different treatments on flax fabrics was evaluated using horizontal flame spread test. The following ranking of the different systems is obtained: TEOS + Additives > TEOS > TEOS + DEPTES ~ TEOS + DEPTES + APTES > multilayers. All the sol–gel coatings improve the flame retardant properties of the flax fabric, except the multilayer treatment. Based on these results, the three most efficient sol–gels were selected to prepare sol–gel-modified flax/PA11 composites. The composite modified with only TEOS showed the best FR properties. Surprisingly, the composite modified with the phosphorus-based flame retardant (AlPi) did not exhibit improved FR properties. This effect was attributed to the fact that the amount of the FR additive deposited on the fabrics was too low.
Open AccessSol–Gel Treatments to Flame Retard PA11/Flax Composites
This work investigates the efficiency of sol–gel treatments to flame retard flax fabric/PA11 composites. Different sol–gel treatments applied to the flax fabrics were prepared using TEOS in combination with phosphorus and/or nitrogen containing co-precursors (DEPTES, APTES) or additives (OP1230, OP1311). When the nitrogen and the phosphorus co-precursors were used, two coating methods were studied: a ‘one-pot’ route and a successive layer deposition method. For the “one-pot” method, the three precursors (TEOS, DEPTES, and APTES) were mixed together in the same solutions whereas for the different layers deposition method, the three different treatments were deposited on the fibers successively, first the TEOS, then a mix of TEOS/DEPTES, and finally a mix of TEOS/APTES. After deposition, the sol–gel coatings were characterized using scanning electron microscope, electron probe microanalyzer, and 29Si and 31P solid-state NMR. When only TEOS or a mix of TEOS and DEPTES is used, homogeneous coatings are obtained presenting well-condensed Si units (mainly Q units). When APTES is added, the coatings are less homogenous and agglomerates are present. A lower condensation rate of the Si network is also noticed by solid-state NMR. When additives are used in combination with TEOS, the TEOS forms a homogenous and continuous film at the surface of the fibers, but the flame retardants are not well distributed and form aggregates. The flame retardant (FR) efficiency of the different treatments on flax fabrics was evaluated using horizontal flame spread test. The following ranking of the different systems is obtained: TEOS + Additives > TEOS > TEOS + DEPTES ~ TEOS + DEPTES + APTES > multilayers. All the sol–gel coatings improve the flame retardant properties of the flax fabric, except the multilayer treatment. Based on these results, the three most efficient sol–gels were selected to prepare sol–gel-modified flax/PA11 composites. The composite modified with only TEOS showed the best FR properties. Surprisingly, the composite modified with the phosphorus-based flame retardant (AlPi) did not exhibit improved FR properties. This effect was attributed to the fact that the amount of the FR additive deposited on the fabrics was too low.
- 1 July 2019
- Published by Elsevier in Polymer Degradation and Stability
- Vol. 165, 68-79
Surface grafting of sepiolite with a phosphaphenanthrene derivative and its flame-retardant mechanism on PLA nanocomposites
- 1 July 2019
- Published by Elsevier in Polymer Degradation and Stability
- Vol. 165, 68-79
Surface grafting of sepiolite with a phosphaphenanthrene derivative and its flame-retardant mechanism on PLA nanocomposites