Suandar Baso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Suandar Baso has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Andi Ardianti
Hasanuddin Univ, Fac Engn, Naval Architecture Dept, Jl Perintis Kemerdekaan Km 10, Makassar 90245, Indonesia
2 shared publicationsAndi Dian Eka Anggriani
Hasanuddin Univ, Fac Engn, Naval Architecture Dept, Jl Perintis Kemerdekaan Km 10, Makassar 90245, Indonesia
2 shared publicationsAhmad Fitriadhy
Programme of Maritime Technology, School of Ocean Engineering, Universiti Malaysia Terengganu, 21030 Kuala Terengganu, Terengganu
1 shared publication- Ahmad Fitriadhy
Faculty of Ocean Engineering Technology, Universiti Malaysia Terengganu, 21030 Kuala Nerus, Terengganu, Malaysia
1 shared publication - Akbar Makmur
Department of Naval Architecture, Faculty of Engineering, Hasanuddin University
1 shared publication Andi Mursid Nugraha
Department of Naval Architecture, Faculty of Engineering, Hasanuddin University, Jalan Poros Malino KM.6 Bontomarannu, 92172, Gowa, Sulawesi Selatan, Indonesia
1 shared publication
Latest Publications
- Open Access
- 30 October 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Numerical Heat Transfer
- Vol. 25 (1) , 73-86
Water Inlet Behavior in Engine Colling Piping on Indonesian Traditional Wooden Vessel Using CFD Simulation
Traditional wooden boat builders in East Kalimantan make the main engine seawater cooling system by using the water currents created by the movement of the ship without the use of suction pumps. This system has been applied to several wooden ships of various sizes. However, the size of the water flow in the pipe is not known by the builders at each ship's speed. Thus, in this paper, an investigation is carried out on seawater cooling pipes on the behavior of fluids moving in the pipes. This study aims to determine the effect of ship speed on the flow of water that occurs in the cooling pipe (inlet and outlet water). The approach taken in this paper is a computer simulation based on Computational Fluid Dynamics (CFD) by analyzing the current flow (Va) of the water discharge in the cooling pipes at speeds of 1 - 9 knots. CFD can show very detailed results in analyzing fluid flow parameters in pipes. Based on the simulations performed, the average flow velocity has increased by around 14.73% for every 1 knot increase in speed. Meanwhile, the average flow rate will increase on the pipe by 14.78% for every 1 knot increase in speed. For the average pressure obtained, the vertical pipe will increase 25% for every 1 knot increase and the horizontal pipe shell will increase 19.86% for every 1 knot increase. Meanwhile, the recommended minimum ship speed is 2.5 knots to get the required cooling seawater flow rate.
- 30 October 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Numerical Heat Transfer
- Vol. 25 (1) , 73-86
Open AccessWater Inlet Behavior in Engine Colling Piping on Indonesian Traditional Wooden Vessel Using CFD Simulation
Traditional wooden boat builders in East Kalimantan make the main engine seawater cooling system by using the water currents created by the movement of the ship without the use of suction pumps. This system has been applied to several wooden ships of various sizes. However, the size of the water flow in the pipe is not known by the builders at each ship's speed. Thus, in this paper, an investigation is carried out on seawater cooling pipes on the behavior of fluids moving in the pipes. This study aims to determine the effect of ship speed on the flow of water that occurs in the cooling pipe (inlet and outlet water). The approach taken in this paper is a computer simulation based on Computational Fluid Dynamics (CFD) by analyzing the current flow (Va) of the water discharge in the cooling pipes at speeds of 1 - 9 knots. CFD can show very detailed results in analyzing fluid flow parameters in pipes. Based on the simulations performed, the average flow velocity has increased by around 14.73% for every 1 knot increase in speed. Meanwhile, the average flow rate will increase on the pipe by 14.78% for every 1 knot increase in speed. For the average pressure obtained, the vertical pipe will increase 25% for every 1 knot increase and the horizontal pipe shell will increase 19.86% for every 1 knot increase. Meanwhile, the recommended minimum ship speed is 2.5 knots to get the required cooling seawater flow rate.
- Open Access
- 6 May 2022
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 14 (4) , 51-66
Computational Investigation into Prediction of Lift Force and Resistance of a Hydrofoil Ship
The characteristics of the fore and aft foils at the various angles of attack incorporated with forward velocities have been vulnerable to induce strong nonlinearities to dynamic lift force and ship resistance. Then, a computational simulation is necessarily required to predict their performances in the calm water condition. This paper presents a computational investigation of the hydrofoil ship on predicting lift and ship’s resistance using fluid dynamic (CFD) simulation approach. Several parameters such as Froude numbers and the angle of attacks both of fore and aft foils have been accordingly taken into account. The results revealed that the subsequent increase on angle of attack of fore and aft foils was directly proportional to the lift force and the ship’s resistance. In addition, the lift force of the aft and fore foils with the angle of attacks of 10 degrees and 5 degrees, respectively, resulted in the significant increase of the lift force and the ship’s resistance. However, the subsequent increase of Froude number from 1.382 up to 1.626 has insignificant effect to the lift and the ship’s resistance of the hydrofoil. It can be concluded that CFD simulation is very beneficial to ensure an operational effectiveness of hydrofoil design towards prediction on the lift force and the hydrofoil’s resistance at the preliminary design stage.
- 6 May 2022
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 14 (4) , 51-66
Open AccessComputational Investigation into Prediction of Lift Force and Resistance of a Hydrofoil Ship
The characteristics of the fore and aft foils at the various angles of attack incorporated with forward velocities have been vulnerable to induce strong nonlinearities to dynamic lift force and ship resistance. Then, a computational simulation is necessarily required to predict their performances in the calm water condition. This paper presents a computational investigation of the hydrofoil ship on predicting lift and ship’s resistance using fluid dynamic (CFD) simulation approach. Several parameters such as Froude numbers and the angle of attacks both of fore and aft foils have been accordingly taken into account. The results revealed that the subsequent increase on angle of attack of fore and aft foils was directly proportional to the lift force and the ship’s resistance. In addition, the lift force of the aft and fore foils with the angle of attacks of 10 degrees and 5 degrees, respectively, resulted in the significant increase of the lift force and the ship’s resistance. However, the subsequent increase of Froude number from 1.382 up to 1.626 has insignificant effect to the lift and the ship’s resistance of the hydrofoil. It can be concluded that CFD simulation is very beneficial to ensure an operational effectiveness of hydrofoil design towards prediction on the lift force and the hydrofoil’s resistance at the preliminary design stage.
- 1 April 2022
- Published by International Journal of Technology in International Journal of Technology
- Vol. 13 (2) , 332-344
Experimental Investigation of Added Resistance of a Ship using a Hydroelastic Body in Waves
Ship resistance is an important characteristic to predict in the preliminary design stage. Proper prediction of ship resistance implies the fulfillment of the required speed and power of a ship. The assumed body characteristics of a ship model should also be properly considered when investigating ship resistance. In the present study, the assumption of a hydroelastic body for a ship model was used in an experiment on total ship resistance and added resistance in calm water and waves. Two hydroelastic models were used: a hydroelastic body with a bulbous bow (HB) and a hydroelastic body without a bulbous bow (HWB). The wavelength considered ranged from 0.5 L to 1.3 L, and the Froude number (Fn) considered ranged from 0.058 to 0.232. In the presented results, the total resistance coefficient of the HWB was higher than that of a rigid body without a bulbous bow (RWB). The average difference of magnitude between the HWB and RWB was 30.49% for calm water conditions and 30.37% for overall wave conditions. The total resistance of the HB was higher than that of the rigid body with a bulbous bow (RB), and the difference of magnitude was approximately 31.47% for calm water conditions and 31.68% for overall wave conditions. The added resistance coefficient of the HWB tended to increase with an increase in the wavelength, from 0.5 L to 1.1 L, and then decrease until 1.5 L. The overall tendency of the added resistance coefficient of the HB was significantly different from the other numerical results. Although the tendencies were different, most of the presented results were in the same range as the other numerical results.
- 1 April 2022
- Published by International Journal of Technology in International Journal of Technology
- Vol. 13 (2) , 332-344
Experimental Investigation of Added Resistance of a Ship using a Hydroelastic Body in Waves
Ship resistance is an important characteristic to predict in the preliminary design stage. Proper prediction of ship resistance implies the fulfillment of the required speed and power of a ship. The assumed body characteristics of a ship model should also be properly considered when investigating ship resistance. In the present study, the assumption of a hydroelastic body for a ship model was used in an experiment on total ship resistance and added resistance in calm water and waves. Two hydroelastic models were used: a hydroelastic body with a bulbous bow (HB) and a hydroelastic body without a bulbous bow (HWB). The wavelength considered ranged from 0.5 L to 1.3 L, and the Froude number (Fn) considered ranged from 0.058 to 0.232. In the presented results, the total resistance coefficient of the HWB was higher than that of a rigid body without a bulbous bow (RWB). The average difference of magnitude between the HWB and RWB was 30.49% for calm water conditions and 30.37% for overall wave conditions. The total resistance of the HB was higher than that of the rigid body with a bulbous bow (RB), and the difference of magnitude was approximately 31.47% for calm water conditions and 31.68% for overall wave conditions. The added resistance coefficient of the HWB tended to increase with an increase in the wavelength, from 0.5 L to 1.1 L, and then decrease until 1.5 L. The overall tendency of the added resistance coefficient of the HB was significantly different from the other numerical results. Although the tendencies were different, most of the presented results were in the same range as the other numerical results.
- Open Access
- 1 June 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 799 (1) , 012002
Investigating the motions’ characteristics of a towed barge in extreme heading wave
A towed barge is one of the typical sea transportation systems that is basically composed of towing and towed ships connected to each other by a tow rope. During a towing operation exposed to rough sea condition, the risk of collision and breakage of a tow rope may be high and the consequences serious. This paper describes an experimental investigation of a towed barge’s motions in heading waves. The effects of various lengths and the configuration of tow ropes incorporated with various loading conditions of the towed barge have been taken into account. Here, three tow-rope lengths were used, namely 1L, 1.5L, and 2L; meanwhile, the two tow-rope configurations i.e., Straight-Tow (ST) and V-Tow (VT) models were applied and incorporated with 50% and 100% of the loading conditions of the towed barge. Regardless of the tow-rope models of ST and VT, the results revealed that the towed barge’s motion responses were generally proportional to the increase of the towline lengths and the towed barge’s loading conditions. It should be noted here that the VT model with 1L tow rope length in the full loaded condition has less RAO of her heave and pitch motions as compared to the other towing arrangements. Merely, this research investigation provides very useful guidance on a ship towing navigation in waves.
- 1 June 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 799 (1) , 012002
Open AccessInvestigating the motions’ characteristics of a towed barge in extreme heading wave
A towed barge is one of the typical sea transportation systems that is basically composed of towing and towed ships connected to each other by a tow rope. During a towing operation exposed to rough sea condition, the risk of collision and breakage of a tow rope may be high and the consequences serious. This paper describes an experimental investigation of a towed barge’s motions in heading waves. The effects of various lengths and the configuration of tow ropes incorporated with various loading conditions of the towed barge have been taken into account. Here, three tow-rope lengths were used, namely 1L, 1.5L, and 2L; meanwhile, the two tow-rope configurations i.e., Straight-Tow (ST) and V-Tow (VT) models were applied and incorporated with 50% and 100% of the loading conditions of the towed barge. Regardless of the tow-rope models of ST and VT, the results revealed that the towed barge’s motion responses were generally proportional to the increase of the towline lengths and the towed barge’s loading conditions. It should be noted here that the VT model with 1L tow rope length in the full loaded condition has less RAO of her heave and pitch motions as compared to the other towing arrangements. Merely, this research investigation provides very useful guidance on a ship towing navigation in waves.
- Open Access
- 29 February 2020
- Published by Center of Technology (COT) in EPI International Journal of Engineering
- Vol. 3 (1) , 69-73
Study on Facility Development of Maccini Baji Port as a Minor and Hub Port for Small Island Connectivity
Maccini Baji port as minor port is a hub of small islands connectivities in Pangkejene and Kepulauan Regency, South Sulawesi. It has strategic role to serve cargo and passenger ship from not only small islands in Pangkejene and Kepulauan Regency but also from outside such as Papua, Maluku, and Nusa Tenggara Timur. Correspondingly, Maccini Baji port has faced the fluctuated increase of visited ships from 2011 to 2018 based on forecasting result by using stepwise and regression methods and has a good potential to be developed especially for cement cargo. This study describes analysis on port facility performance of Maccini Baji and its development. The research result has shown the berth occupancy ratio (BOR) of Maccini Baji port in 2022 will reach 61%. This has become a primarily point to consider in lengthening berth of Maccini Baji port. Therefore, the port berth of Maccini Baji should be lengthened 272 meters where existing berth length is 225 meters. In addition, basin and anchorage area will be also developed where the dimensions of turning basin will be 6 meters in depth, 121.8 meters in diameters, and its area will be 116 m2. The dimensions of anchorage area will be 6 metres in depth, and 105.9 meters in radius and its area will be 35.21 m2. Based on SWOT analysis, some aspects will be considered to succesfully develop Maccini Baji port such as geographic location, port facility improvement, increas of service capacity and facility efficiency, development of hinterland area, local government participation.
- 29 February 2020
- Published by Center of Technology (COT) in EPI International Journal of Engineering
- Vol. 3 (1) , 69-73
Open AccessStudy on Facility Development of Maccini Baji Port as a Minor and Hub Port for Small Island Connectivity
Maccini Baji port as minor port is a hub of small islands connectivities in Pangkejene and Kepulauan Regency, South Sulawesi. It has strategic role to serve cargo and passenger ship from not only small islands in Pangkejene and Kepulauan Regency but also from outside such as Papua, Maluku, and Nusa Tenggara Timur. Correspondingly, Maccini Baji port has faced the fluctuated increase of visited ships from 2011 to 2018 based on forecasting result by using stepwise and regression methods and has a good potential to be developed especially for cement cargo. This study describes analysis on port facility performance of Maccini Baji and its development. The research result has shown the berth occupancy ratio (BOR) of Maccini Baji port in 2022 will reach 61%. This has become a primarily point to consider in lengthening berth of Maccini Baji port. Therefore, the port berth of Maccini Baji should be lengthened 272 meters where existing berth length is 225 meters. In addition, basin and anchorage area will be also developed where the dimensions of turning basin will be 6 meters in depth, 121.8 meters in diameters, and its area will be 116 m2. The dimensions of anchorage area will be 6 metres in depth, and 105.9 meters in radius and its area will be 35.21 m2. Based on SWOT analysis, some aspects will be considered to succesfully develop Maccini Baji port such as geographic location, port facility improvement, increas of service capacity and facility efficiency, development of hinterland area, local government participation.
- Open Access
- 25 April 2019
- Published by International Journal of Technology in International Journal of Technology
- Vol. 10 (2) , 236-246
Predicting the Motions of a Fishing Boat Caused by Improving the Stern Part using a Hybrid Particle-Grid Scheme
Improving a ship’s stern part could help to reduce greenhouse gases and costs. However, a ship sailing in actual conditions experiences disturbances that can affect its performance. Ship performance is an important aspect of the design process that guarantees ship safety. The heave and pitch motions of an improved fishing boat were predicted numerically by using a hybrid scheme of Eulerian grid-Lagrangian particle, hereinafter improving its stern part and attaching an additional part. The stern part improvement and additional structure attachment affected an increase on the heave amplitude from the ship’s basic form by 5% to 10%. Moreover, the improvement of the stern part in the bottom area contributed to a better heave amplitude than that of the side area. Finally, the pitch amplitude for all forms was relatively small and affected an increase of 5% to 9%, dependent on the form. The improvement had a greater effect on heave motion than pitch.
- 25 April 2019
- Published by International Journal of Technology in International Journal of Technology
- Vol. 10 (2) , 236-246
Open AccessPredicting the Motions of a Fishing Boat Caused by Improving the Stern Part using a Hybrid Particle-Grid Scheme
Improving a ship’s stern part could help to reduce greenhouse gases and costs. However, a ship sailing in actual conditions experiences disturbances that can affect its performance. Ship performance is an important aspect of the design process that guarantees ship safety. The heave and pitch motions of an improved fishing boat were predicted numerically by using a hybrid scheme of Eulerian grid-Lagrangian particle, hereinafter improving its stern part and attaching an additional part. The stern part improvement and additional structure attachment affected an increase on the heave amplitude from the ship’s basic form by 5% to 10%. Moreover, the improvement of the stern part in the bottom area contributed to a better heave amplitude than that of the side area. Finally, the pitch amplitude for all forms was relatively small and affected an increase of 5% to 9%, dependent on the form. The improvement had a greater effect on heave motion than pitch.