Jun-Ichi Itoh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jun-Ichi Itoh has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Hiroki Watanabe
Department of Electrical, Electronics, and Information Engineering, Nagaoka University of Technology, Nagaoka, Japan
10 shared publications Keisuke Kusaka
Nagaoka University of Technology
9 shared publications- Keisuke Kusaka
Nagaoka University of Technology
9 shared publications Hiroki Watanabe
Nagaoka University of Technology
5 shared publicationsJunnosuke Haruna
Tokyo University of Science
3 shared publicationsNagisa Takaoka
Nagaoka University of Technology
3 shared publications
Latest Publications
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15577-15593
Three-Level Current-Fed Dual Active Bridge Converter for Wide Voltage Range Interconnected to a 1500-V DC Grid
This article proposes a highly efficient control method over a wide operating range in a flying capacitor-type current-fed dual active bridge converter. The circuit configuration on the low-voltage side integrates an interleaved boost converter and a single-phase inverter. The circuit configuration on the high-voltage side consists of a flying capacitor (FC) converter to accept a medium voltage of 1500 V DC grid. The output voltage of the FC converter is switched between the DC-grid voltage and half of the DC-grid voltage, depending on the input voltage and load conditions, to improve efficiency. A flying capacitor-type current-fed dual active bridge (FCCF-DAB) converter applies a triangular current mode (TCM) to achieve zero voltage switching (ZVS) for the low-voltage side. The operating condition of the DC-bus voltage has to be determined to achieve the minimum loss, which depends on the balance between the switching and conduction losses. Based on the loss analysis, the optimal operating point is identified and utilized in the experiment. The experimental results with the minimum loss DC-bus voltage demonstrate that conversion loss is reduced by 23.7% at an input voltage of 300 V and an output power of 7.8 kW. Furthermore, a design guideline for achieving ZVS under all voltage and load conditions is presented. The validity of the guideline is demonstrated through experiments using a prototype.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15577-15593
Three-Level Current-Fed Dual Active Bridge Converter for Wide Voltage Range Interconnected to a 1500-V DC Grid
This article proposes a highly efficient control method over a wide operating range in a flying capacitor-type current-fed dual active bridge converter. The circuit configuration on the low-voltage side integrates an interleaved boost converter and a single-phase inverter. The circuit configuration on the high-voltage side consists of a flying capacitor (FC) converter to accept a medium voltage of 1500 V DC grid. The output voltage of the FC converter is switched between the DC-grid voltage and half of the DC-grid voltage, depending on the input voltage and load conditions, to improve efficiency. A flying capacitor-type current-fed dual active bridge (FCCF-DAB) converter applies a triangular current mode (TCM) to achieve zero voltage switching (ZVS) for the low-voltage side. The operating condition of the DC-bus voltage has to be determined to achieve the minimum loss, which depends on the balance between the switching and conduction losses. Based on the loss analysis, the optimal operating point is identified and utilized in the experiment. The experimental results with the minimum loss DC-bus voltage demonstrate that conversion loss is reduced by 23.7% at an input voltage of 300 V and an output power of 7.8 kW. Furthermore, a design guideline for achieving ZVS under all voltage and load conditions is presented. The validity of the guideline is demonstrated through experiments using a prototype.
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (6) , 8966-8977
Power Imbalance Compensation of Droop-Based Distributed Control With Wireless Communication in Multi-Cell AC-DC Converters
This paper proposes an enhanced distributed control scheme with power imbalance compensation for an Input-Parallel-Output-Parallel (IPOP) AC-DC converter featuring a power imbalance compensator that incorporates non-instantaneous values. Power-sharing imbalances are a common issue in parallel-connected cell converters due to wiring resistance between the load and individual cells under conventional droop control. The proposed compensator, placed in the outer loop of the voltage and current feedback loops, effectively mitigates these imbalances. By leveraging non-instantaneous values, the control scheme accepts low-bandwidth communication, enabling the use of low-speed wireless modules and reducing the required signal lines, thus enhancing system flexibility. The experimental validation is conducted using a 7.2-kW prototype comprising six cells with integrated wireless communication modules. The results demonstrate that the proposed method reduces output current imbalance by up to 94% compared to conventional approaches.
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (6) , 8966-8977
Power Imbalance Compensation of Droop-Based Distributed Control With Wireless Communication in Multi-Cell AC-DC Converters
This paper proposes an enhanced distributed control scheme with power imbalance compensation for an Input-Parallel-Output-Parallel (IPOP) AC-DC converter featuring a power imbalance compensator that incorporates non-instantaneous values. Power-sharing imbalances are a common issue in parallel-connected cell converters due to wiring resistance between the load and individual cells under conventional droop control. The proposed compensator, placed in the outer loop of the voltage and current feedback loops, effectively mitigates these imbalances. By leveraging non-instantaneous values, the control scheme accepts low-bandwidth communication, enabling the use of low-speed wireless modules and reducing the required signal lines, thus enhancing system flexibility. The experimental validation is conducted using a 7.2-kW prototype comprising six cells with integrated wireless communication modules. The results demonstrate that the proposed method reduces output current imbalance by up to 94% compared to conventional approaches.
- 1 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (2) , 3411-3417
Universal Smart Power Module (USPM) for Carbon Neutral Society
This paper presents a Universal Smart Power Module (USPM) which responds instantaneously to fluctuating power sources such as solar and wind power and fully addresses the rapidly expanding renewable energy market by combining universality and smartness. USPM consists of a main circuit as an H-bridge converter, high-speed controller, gate driver, and EMI filter into one module. Conventional power electronics design requires complicated know-how and specialized skills such as circuit design, digital control, thermal design, and EMI. The USPM concept simplifies the power electronics design because this system realizes every power converter by a combination of several USPMs. The USPM system consists of the master controller and several USPMs. The master controller gives voltage and current commands to USPMs by wireless communication to regulate the operation of USPMs. USPM realizes excellent feedback control by the high-speed controller in order to follow the command from the master controller rapidly. The core power module using the wide-bandgap device in USPM is also developed to improve the switching characteristics and the power density of USPM. As the technology for ultra-miniaturization, ADB (Atomic Diffusion Bonding) is developed and applied to the drain side of the SiC-MOSFET to achieve low thermal resistance, and bumping technology to the source side of it to achieve low inductance. This paper introduces the detail of the concept of the USPM systems and the core power module. Finally, the example of the USPM system for the PV power conditioner is demonstrated by the experiment.
- 1 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (2) , 3411-3417
Universal Smart Power Module (USPM) for Carbon Neutral Society
This paper presents a Universal Smart Power Module (USPM) which responds instantaneously to fluctuating power sources such as solar and wind power and fully addresses the rapidly expanding renewable energy market by combining universality and smartness. USPM consists of a main circuit as an H-bridge converter, high-speed controller, gate driver, and EMI filter into one module. Conventional power electronics design requires complicated know-how and specialized skills such as circuit design, digital control, thermal design, and EMI. The USPM concept simplifies the power electronics design because this system realizes every power converter by a combination of several USPMs. The USPM system consists of the master controller and several USPMs. The master controller gives voltage and current commands to USPMs by wireless communication to regulate the operation of USPMs. USPM realizes excellent feedback control by the high-speed controller in order to follow the command from the master controller rapidly. The core power module using the wide-bandgap device in USPM is also developed to improve the switching characteristics and the power density of USPM. As the technology for ultra-miniaturization, ADB (Atomic Diffusion Bonding) is developed and applied to the drain side of the SiC-MOSFET to achieve low thermal resistance, and bumping technology to the source side of it to achieve low inductance. This paper introduces the detail of the concept of the USPM systems and the core power module. Finally, the example of the USPM system for the PV power conditioner is demonstrated by the experiment.
- 23 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (12) , 15242-15252
Distributed Control Method for Power Conversion System With Series-Connected Autonomous Modular Converters
This article proposes a current droop control for series-connected current source converters in a universal smart power module (USPM) concept. In this concept, power conversion systems are constructed by USPMs, which have a high-speed controller and autonomous distributed control. USPM enhances versatility by its high flexibility and usability compared to power electronics building blocks, which is a similar concept. In this system, noninterference control is required because these USPMs are operated independently without sharing information with each other. Droop control for the voltage source converter is a common solution for parallel-connected converters. Likewise, a stabilization method for the current-source-type converter connected in series is necessary for the USPM system. The proposed method in this article solves these problems. In particular, the configuration of the current controller and its gain design method is verified in order to achieve a stable condition and high-speed response. The experimental results for the 500-W system reveal that the stability limit of the PI control adopting the proposed current droop control agrees with the analytical results with an error of 1.3%. Furthermore, this article demonstrates that the current deviation agrees with that of the design value with an error of 3.0% or less.
- 23 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (12) , 15242-15252
Distributed Control Method for Power Conversion System With Series-Connected Autonomous Modular Converters
This article proposes a current droop control for series-connected current source converters in a universal smart power module (USPM) concept. In this concept, power conversion systems are constructed by USPMs, which have a high-speed controller and autonomous distributed control. USPM enhances versatility by its high flexibility and usability compared to power electronics building blocks, which is a similar concept. In this system, noninterference control is required because these USPMs are operated independently without sharing information with each other. Droop control for the voltage source converter is a common solution for parallel-connected converters. Likewise, a stabilization method for the current-source-type converter connected in series is necessary for the USPM system. The proposed method in this article solves these problems. In particular, the configuration of the current controller and its gain design method is verified in order to achieve a stable condition and high-speed response. The experimental results for the 500-W system reveal that the stability limit of the PI control adopting the proposed current droop control agrees with the analytical results with an error of 1.3%. Furthermore, this article demonstrates that the current deviation agrees with that of the design value with an error of 3.0% or less.
- Open Access
- 1 July 2023
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 12 (4) , 726-734
Development of Current-Fed DAB Converter Applying Triangular Current Mode for Wide Voltage Applications
This paper proposes a control and modulation method for a Current-Fed Dual Active Bridge (DAB) converter to improve the conversion efficiency for wide voltage range applications. The current-fed DAB converter is preferred in battery applications owing to its high-power density and low current ripple. On the other hand, the high-conversion efficiency range is limited to close to the nominal DC voltage condition as the DAB converter. The proposed method provides Zero-Voltage-Switching (ZVS) in a wide DC voltage range by Triangular Current Mode (TCM). Furthermore, the proposed control reduces the inductor RMS current compared with the DAB converter to minimize the conduction loss. The validity of the proposed method is established by experimental results. According to the experiment using a 2-kW prototype, the conversion efficiency reached 97.2% when the input voltage was varied by 50% from the nominal DC voltage, then the conversion loss was reduced by 52.5% owing to the proposed control. Finally, the maximum power density of the current-fed DAB converter was improved by 38.1% compared to that of the DAB converter.
- 1 July 2023
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 12 (4) , 726-734
Open AccessDevelopment of Current-Fed DAB Converter Applying Triangular Current Mode for Wide Voltage Applications
This paper proposes a control and modulation method for a Current-Fed Dual Active Bridge (DAB) converter to improve the conversion efficiency for wide voltage range applications. The current-fed DAB converter is preferred in battery applications owing to its high-power density and low current ripple. On the other hand, the high-conversion efficiency range is limited to close to the nominal DC voltage condition as the DAB converter. The proposed method provides Zero-Voltage-Switching (ZVS) in a wide DC voltage range by Triangular Current Mode (TCM). Furthermore, the proposed control reduces the inductor RMS current compared with the DAB converter to minimize the conduction loss. The validity of the proposed method is established by experimental results. According to the experiment using a 2-kW prototype, the conversion efficiency reached 97.2% when the input voltage was varied by 50% from the nominal DC voltage, then the conversion loss was reduced by 52.5% owing to the proposed control. Finally, the maximum power density of the current-fed DAB converter was improved by 38.1% compared to that of the DAB converter.
- 23 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (7) , 8102-8114
Theoretical Study of Rampwise DPWM Technique to Reduce Motor Acoustic Noise
Motor acoustic noise generated near living environments, such as elevators and electric vehicles, may cause discomfort. In order to reduce the acoustic noise, the switching frequency is set to the high side of the audible frequency range. In this case, however, the switching loss is increased. The conventional discontinuous pulsewidth modulation (DPWM) method is widely used since it can reduce the switching loss drastically. However, it produces larger acoustic noise than the conventional sinusoidal pulsewidth modulation method. The authors have previously proposed “Rampwise DPWM technique,” which can reduce both acoustic noise and switching loss. In this article, the line–line voltage with the proposed Rampwise DPWM technique is expanded into a real-valued Fourier series, and the frequency characteristics are analyzed. It is theoretically confirmed that the rampwise part in the Rampwise DPWM technique can achieve the reduction of motor acoustic noise. Furthermore, the reduction effect of motor acoustic noise with the Rampwise DPWM technique is theoretically and experimentally verified.
- 23 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (7) , 8102-8114
Theoretical Study of Rampwise DPWM Technique to Reduce Motor Acoustic Noise
Motor acoustic noise generated near living environments, such as elevators and electric vehicles, may cause discomfort. In order to reduce the acoustic noise, the switching frequency is set to the high side of the audible frequency range. In this case, however, the switching loss is increased. The conventional discontinuous pulsewidth modulation (DPWM) method is widely used since it can reduce the switching loss drastically. However, it produces larger acoustic noise than the conventional sinusoidal pulsewidth modulation method. The authors have previously proposed “Rampwise DPWM technique,” which can reduce both acoustic noise and switching loss. In this article, the line–line voltage with the proposed Rampwise DPWM technique is expanded into a real-valued Fourier series, and the frequency characteristics are analyzed. It is theoretically confirmed that the rampwise part in the Rampwise DPWM technique can achieve the reduction of motor acoustic noise. Furthermore, the reduction effect of motor acoustic noise with the Rampwise DPWM technique is theoretically and experimentally verified.
- 11 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 50 (12) , 4882-4888
Self-Powered Gate Drive Circuits With Optical Signal Isolation for In-Vehicle Marx Circuit of Ozonizer
Reducing the cost of a Marx circuit as a high-voltage power supply for nitrogen oxide (NOx) decomposition for diesel vehicles is required. The Marx circuit with MOSFETs has an advantage in size compared to the Marx circuit with gap switches. However, the Marx circuit with MOSFETs needs gate drive circuits on the gate of each MOSFET. The gate signal and drive power must be supplied to each gate with isolation in a low-cost way. However, the transformer for the isolation with high withstand voltage, such as 10 kV or more, is typically high cost because of the low demand. This article proposes the self-powered gate drive circuit using the charging path of the Marx circuit. The proposed gate drive circuit only requires a low withstand voltage because the power for the MOSFET on the $n$ th stage is supplied from the ( $n -1$ )th stage via a low-voltage transformer. Besides, the gate signal is transmitted through pairs of LEDs and photodiodes instead of high-cost optical fibers. The proposed gate drive circuits are developed and implemented into a prototype of the Marx circuit with an output voltage of 4 kV. From the experiments, it is demonstrated that the proposed drive circuits provide both drive power and gate signal.
- 11 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 50 (12) , 4882-4888
Self-Powered Gate Drive Circuits With Optical Signal Isolation for In-Vehicle Marx Circuit of Ozonizer
Reducing the cost of a Marx circuit as a high-voltage power supply for nitrogen oxide (NOx) decomposition for diesel vehicles is required. The Marx circuit with MOSFETs has an advantage in size compared to the Marx circuit with gap switches. However, the Marx circuit with MOSFETs needs gate drive circuits on the gate of each MOSFET. The gate signal and drive power must be supplied to each gate with isolation in a low-cost way. However, the transformer for the isolation with high withstand voltage, such as 10 kV or more, is typically high cost because of the low demand. This article proposes the self-powered gate drive circuit using the charging path of the Marx circuit. The proposed gate drive circuit only requires a low withstand voltage because the power for the MOSFET on the $n$ th stage is supplied from the ( $n -1$ )th stage via a low-voltage transformer. Besides, the gate signal is transmitted through pairs of LEDs and photodiodes instead of high-cost optical fibers. The proposed gate drive circuits are developed and implemented into a prototype of the Marx circuit with an output voltage of 4 kV. From the experiments, it is demonstrated that the proposed drive circuits provide both drive power and gate signal.
- 1 March 2022
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 11 (2) , 341-350
Isolated DC to Single-Phase AC Converter with Active Power Decoupling Capability Using Coupled Inductor
This paper proposes a novel active power decoupling circuit that is integrated with an interleaved boost converter for isolated DC to single-phase AC conversion applications. The proposed isolated converter consists of two full-bridge inverters with a coupled inductor, a small buffer capacitor for active power decoupling, and a diode rectifier. Further, the proposed isolated converter is controlled for active power decoupling and DC to single-phase AC power conversion independently by the coupling inductor and common-mode operation of the interleaved boost converter, respectively. This paper presents the control method of the proposed converter and design criteria of the passive components. In addition, the performance of the proposed isolated converter is demonstrated by the experimental results in order to confirm the validity of the proposed method. As the experimental results, the second-order harmonic due to the double-line frequency power ripple is reduced by 84.5% owing to the active power decoupling capability. Finally, a maximum efficiency of 94.5% is obtained using the proposed converter.
- 1 March 2022
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 11 (2) , 341-350
Isolated DC to Single-Phase AC Converter with Active Power Decoupling Capability Using Coupled Inductor
This paper proposes a novel active power decoupling circuit that is integrated with an interleaved boost converter for isolated DC to single-phase AC conversion applications. The proposed isolated converter consists of two full-bridge inverters with a coupled inductor, a small buffer capacitor for active power decoupling, and a diode rectifier. Further, the proposed isolated converter is controlled for active power decoupling and DC to single-phase AC power conversion independently by the coupling inductor and common-mode operation of the interleaved boost converter, respectively. This paper presents the control method of the proposed converter and design criteria of the passive components. In addition, the performance of the proposed isolated converter is demonstrated by the experimental results in order to confirm the validity of the proposed method. As the experimental results, the second-order harmonic due to the double-line frequency power ripple is reduced by 84.5% owing to the active power decoupling capability. Finally, a maximum efficiency of 94.5% is obtained using the proposed converter.
- 1 January 2022
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 11 (5) , 722-729
Low Vibration Stopping Method for the Compressor Driving Motor
This paper proposes a low vibration stopping method by switching between the free-run and short-circuit braking modes of a compressor. Vibrations are generated by the bouncing of the rotor caused by load torque fluctuations. The proposed method suppresses the bouncing by stopping the motor during the suction process, thereby preventing the generation of a large torque. In order to stop the motor during the suction process, the proposed method switches from the free-run to short-circuit braking mode at the top dead center, which is the starting point of the suction pro-cess. Furthermore, the inrush current during the short-circuit braking mode is suppressed using a hysteresis current controller. The vibrations are evaluated under four pressure conditions using the conventional and proposed methods. The results show that, the proposed method achieves more than 50% reduction in the amplitudes of the vibrations at all four pressure conditions. Notably, the proposed method reduces the amplitude of the vibration by 71% under the high-pressure condition.
- 1 January 2022
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Journal of Industry Applications
- Vol. 11 (5) , 722-729
Low Vibration Stopping Method for the Compressor Driving Motor
This paper proposes a low vibration stopping method by switching between the free-run and short-circuit braking modes of a compressor. Vibrations are generated by the bouncing of the rotor caused by load torque fluctuations. The proposed method suppresses the bouncing by stopping the motor during the suction process, thereby preventing the generation of a large torque. In order to stop the motor during the suction process, the proposed method switches from the free-run to short-circuit braking mode at the top dead center, which is the starting point of the suction pro-cess. Furthermore, the inrush current during the short-circuit braking mode is suppressed using a hysteresis current controller. The vibrations are evaluated under four pressure conditions using the conventional and proposed methods. The results show that, the proposed method achieves more than 50% reduction in the amplitudes of the vibrations at all four pressure conditions. Notably, the proposed method reduces the amplitude of the vibration by 71% under the high-pressure condition.
- 18 October 2021
- Published by Wiley in Electrical Engineering in Japan
- Vol. 214 (4) , e23350
Development of a battery management system with flying capacitor‐type multiport converter in the discontinuous current mode
This paper proposes a multiport converter based on a flying capacitor converter (FCC) topology for use in a battery management system. The proposed circuit operates in discontinuous current mode (DCM) and pulse frequency modulation (PFM) in order to reduce inductor volume. The circuit achieves load fluctuation compensation and maximum power point tracking (MPPT) of the photovoltaic (PV) system by deciding duty ratio based on load current and PV output current. According to the experimental results, an efficiency of more than 95.8% was achieved under all operation conditions. In addition, the maximum efficiency reached 98.8% at the rated load (750 W). Furthermore, the inductor volume reduced by 85.5% compared to that of the conventional circuit (CCM) using two inductors.
- 18 October 2021
- Published by Wiley in Electrical Engineering in Japan
- Vol. 214 (4) , e23350
Development of a battery management system with flying capacitor‐type multiport converter in the discontinuous current mode
This paper proposes a multiport converter based on a flying capacitor converter (FCC) topology for use in a battery management system. The proposed circuit operates in discontinuous current mode (DCM) and pulse frequency modulation (PFM) in order to reduce inductor volume. The circuit achieves load fluctuation compensation and maximum power point tracking (MPPT) of the photovoltaic (PV) system by deciding duty ratio based on load current and PV output current. According to the experimental results, an efficiency of more than 95.8% was achieved under all operation conditions. In addition, the maximum efficiency reached 98.8% at the rated load (750 W). Furthermore, the inductor volume reduced by 85.5% compared to that of the conventional circuit (CCM) using two inductors.