Gang Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Gang Zhao has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Yun-Qing Gu
Zhejiang University of Technology
2 shared publicationsEvan Wang
Institut National Polytechnique of Grenoble, Joseph Fourier University, Grenoble 38031, France
1 shared publicationJie-Gang Mou
College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310014, China
1 shared publicationMuhammad Farid
Harbin Engineering University
1 shared publicationTian-Xing Fan
College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310014, China
1 shared publicationTran Linh Khuong
Harbin Engineering University
1 shared publication
Latest Publications
- 28 April 2018
- Published by Springer Nature in Journal of Central South University
- Vol. 25 (4) , 855-865
Bionic structure of shark’s gill jet orifice based on artificial muscle
- 28 April 2018
- Published by Springer Nature in Journal of Central South University
- Vol. 25 (4) , 855-865
Bionic structure of shark’s gill jet orifice based on artificial muscle
- 1 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 347-351
Harmonic analysis and suppression of electric vehicle charging station
Electric vehicle is important to solve energy and environmental problems. Electric vehicles charger is a kind of strong nonlinear load, which brings harmonic pollution to grid when it works. To analyze and suppress its harmonic is of great significance for large-scale construction of charger in the future. Utilizing PSCAD software, simulation model for 6-plus uncontrolled rectifier was built, and harmonic of single or multiple chargers was analyzed in this paper. Finally, passive filter was used in the suppression of harmonic, and the expected effect was achieved, which provided a theoretical reference for large-scale construction of charging stations in the future.
- 1 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 347-351
Harmonic analysis and suppression of electric vehicle charging station
Electric vehicle is important to solve energy and environmental problems. Electric vehicles charger is a kind of strong nonlinear load, which brings harmonic pollution to grid when it works. To analyze and suppress its harmonic is of great significance for large-scale construction of charger in the future. Utilizing PSCAD software, simulation model for 6-plus uncontrolled rectifier was built, and harmonic of single or multiple chargers was analyzed in this paper. Finally, passive filter was used in the suppression of harmonic, and the expected effect was achieved, which provided a theoretical reference for large-scale construction of charging stations in the future.
- 19 December 2016
- Published by Springer Nature in Cellulose
- Vol. 24 (2) , 441-445
A naturally crosslinked chitosan based ionic actuator with cathode deflection phenomenon
- 19 December 2016
- Published by Springer Nature in Cellulose
- Vol. 24 (2) , 441-445
A naturally crosslinked chitosan based ionic actuator with cathode deflection phenomenon
- Open Access
- 15 February 2016
- Published by Hindawi Limited in Applied Bionics and Biomechanics
- Vol. 2016, 1-10
Experiment Research on Hot-Rolling Processing of Nonsmooth Pit Surface
In order to achieve the nonsmooth surface drag reduction structure on the inner polymer coating of oil and gas pipelines and improve the efficiency of pipeline transport, a structural model of the machining robot on the pipe inner coating is established. Based on machining robot, an experimental technique is applied to research embossing and coating problems of rolling-head, and then the molding process rules under different conditions of rolling temperatures speeds and depth are analyzed. Also, an orthogonal experiment analysis method is employed to analyze the different effects of hot-rolling process apparatus on the embossed pits morphology and quality of rolling. The results also reveal that elevating the rolling temperature or decreasing the rolling speed can also improve the pit structure replication rates of the polymer coating surface, and the rolling feed has little effect on replication rates. After the rolling-head separates from the polymer coating, phenomenon of rebounding and refluxing of the polymer coating occurs, which is the reason of inability of the process. A continuous hot-rolling method for processing is used in the robot and the hot-rolling process of the processing apparatus is put in a dynamics analysis.
- 15 February 2016
- Published by Hindawi Limited in Applied Bionics and Biomechanics
- Vol. 2016, 1-10
Open AccessExperiment Research on Hot-Rolling Processing of Nonsmooth Pit Surface
In order to achieve the nonsmooth surface drag reduction structure on the inner polymer coating of oil and gas pipelines and improve the efficiency of pipeline transport, a structural model of the machining robot on the pipe inner coating is established. Based on machining robot, an experimental technique is applied to research embossing and coating problems of rolling-head, and then the molding process rules under different conditions of rolling temperatures speeds and depth are analyzed. Also, an orthogonal experiment analysis method is employed to analyze the different effects of hot-rolling process apparatus on the embossed pits morphology and quality of rolling. The results also reveal that elevating the rolling temperature or decreasing the rolling speed can also improve the pit structure replication rates of the polymer coating surface, and the rolling feed has little effect on replication rates. After the rolling-head separates from the polymer coating, phenomenon of rebounding and refluxing of the polymer coating occurs, which is the reason of inability of the process. A continuous hot-rolling method for processing is used in the robot and the hot-rolling process of the processing apparatus is put in a dynamics analysis.
- 1 February 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 889-890, 938-941
Forward Kinematic Modeling and Simulation of Ionic Polymer Metal Composites (IPMC) Actuators for Bionic Knee Joint
Ionic Polymer Composite Material (IPMC) is a flexible material and has revealed many advantages to encourage the scientists and researchers to investigate its characteristics for practical applications in various fields. The ongoing research can be divided into two branches. One deals with the improvement of the material properties to make it more useful and reliable while the other involves the exploration of new application areas. In this paper, Firstly, a new application of IPMC is suggested to actuate a rigid link that can mimic a bionic knee joint for a grass hopper manipulator. Secondly, forward kinematic model is proposed for the manipulator by employing geometric coordinate system method. Lastly, wolfram mathematica software is employed for the simulation of the model. The simulation results based on the model are found very encouraging to lure the article team to carry on the research idea for manufacturing and testing for the comparison of both types of results.
- 1 February 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 889-890, 938-941
Forward Kinematic Modeling and Simulation of Ionic Polymer Metal Composites (IPMC) Actuators for Bionic Knee Joint
Ionic Polymer Composite Material (IPMC) is a flexible material and has revealed many advantages to encourage the scientists and researchers to investigate its characteristics for practical applications in various fields. The ongoing research can be divided into two branches. One deals with the improvement of the material properties to make it more useful and reliable while the other involves the exploration of new application areas. In this paper, Firstly, a new application of IPMC is suggested to actuate a rigid link that can mimic a bionic knee joint for a grass hopper manipulator. Secondly, forward kinematic model is proposed for the manipulator by employing geometric coordinate system method. Lastly, wolfram mathematica software is employed for the simulation of the model. The simulation results based on the model are found very encouraging to lure the article team to carry on the research idea for manufacturing and testing for the comparison of both types of results.