JSJunjie Shi

Junjie Shi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Junjie Shi has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Wide-range soft anisotropic thermistor with a direct wireless radio frequency interface

    by Mahmoud Wagih, Mahmoud Wagih, Junjie Shi, Junjie Shi, Menglong Li, Menglong Li, Abiodun Komolafe, Abiodun Komolafe, Thomas Whittaker, Thomas Whittaker, et al.

    Temperature sensors are one of the most fundamental sensors and are found in industrial, environmental, and biomedical applications. The traditional approach of reading the resistive response of Positive Temperature Coefficient thermistors at DC hindered their adoption as wide-range temperature sensors. Here, we present a large-area thermistor, based on a flexible and stretchable short carbon fibre incorporated Polydimethylsiloxane composite, enabled by a radio frequency sensing interface. The radio frequency readout overcomes the decades-old sensing range limit of thermistors. The composite exhibits a resistance sensitivity over 1000 °C−1, while maintaining stability against bending (20,000 cycles) and stretching (1000 cycles). Leveraging its large-area processing, the anisotropic composite is used as a substrate for sub-6 GHz radio frequency components, where the thermistor-based microwave resonators achieve a wide temperature sensing range (30 to 205 °C) compared to reported flexible temperature sensors, and high sensitivity (3.2 MHz/°C) compared to radio frequency temperature sensors. Wireless sensing is demonstrated using a microstrip patch antenna based on a thermistor substrate, and a battery-less radio frequency identification tag. This radio frequency-based sensor readout technique could enable functional materials to be directly integrated in wireless sensing applications.


  • Open Access

    Toward the Optimal Antenna-Based Wireless Sensing Strategy: An Ice Sensing Case Study

    by Mahmoud Wagih, Junjie Shi

    Remote ice detection has emerged as an application of Radio Frequency (RF) sensors. While antenna-based “RFID” sensing can detect various measurands, antenna-based sensors are not currently designed based on a systematic methodology, and in most cases may have a low sensitivity requiring specialist hardware or broadband interrogation signals, incompatible with spectrum regulations. Here, we develop a systematic methodology for designing an antenna-based sensor, applicable to measurands inducing a dielectric change in the near-field of the antenna. The proposed methodology is applied to designing printable antennas as highly-sensitive sensors for detecting and measuring the thickness of ice, demonstrating best-in-class sensory response compared to more complex antenna designs. Antenna design is investigated systematically for wireless interrogation in the 2.4 GHz band, where it is found that a loop antenna outperforms a dipole owing to its more distributed capacitance. The antenna’s realized gain was identified as the optimum parameter-under-test, with “positive” sensing proposed as a method of improving linearity and immunity to interference. The developed loop antenna sensor exhibits resilience to interference and applicability to different real-world deployment environments, demonstrated through over 80% average ice thickness measurement accuracy and at least 5 dB real-time sensitivity to ice deposition.


  • Open Access

    Textile Tactile Senor Based on Ferroelectret for Gesture Recognition

    by Junjie Shi, Mahmoud Wagih

    Ferroelectret is a charged polymer with cellular void structures that create giant dipole moments across the material’s thickness. In this work, we present the first realization of a wearable textile substrate tactile sensor based on Polypropylene (PP) ferroelectret material for gesture recognition. As a result, the sensitivity of the fabricated sensor is 0.21 V/kPa in the pressure range of 0–20 kPa. The ferroelectret tactile sensor adheres to a glove’s surface for detecting human movements such as bending or the relaxation motion of the palm and the bending or stretching motion of each finger, enabling the successful detection of small finger gestures around a 400 mV output.


  • The effect of fabric properties on the performance of a textile based ferroelectret generator toward human body energy harvesting

    by Junjie Shi, Steve P Beeby

    This paper reports the lamination of two thin fluorinated ethylene propylene (FEP) films onto the back and front surfaces of a conventional textile forming a sandwich structure which creates a textile-based ferroelectret. In this work, we study the effect of the physical properties and dimensions of the textile on the piezoelectric properties and energy harvesting performance of the ferroelectret. Five different fabrics with different thicknesses and Young’s modulus were used to form textile based ferroelectret harvesters. Thinner textiles result in increased piezoelectric properties of the fabricated FEP textile ferroelectret. The highest measured stable maximum piezoelectric coefficient d 33 of 987 pC N −1 was achieved by the thinnest silk textile FEP ferroelectret. The energy harvester based on the FEP-silk textile ferroelectret generates a peak output power density of 2.26 µ W cm −2 . The textile ferroelectret can charge a 10 µ F capacitor used to store the harvested energy to 3.2 V in 40 s. This corresponds to an average output power of 1.07 µ W when subjected to compressive pressures of 30 kPa applied at a frequency of 1 Hz with a 90 MΩ loading resistance.


  • Open Access

    E-Textile Technology Review–From Materials to Application

    by Abiodun Komolafe, Bahareh Zaghari, Russel Torah, Alex S. Weddell, Hamideh Khanbareh, Zois Michail Tsikriteas, Mark Vousden, Mahmoud Wagih, Ulises Tronco Jurado, Junjie Shi, et al.

    Wearable devices are ideal for personalized electronic applications in several domains such as healthcare, entertainment, sports and military. Although wearable technology is a growing market, current wearable devices are predominantly battery powered accessory devices, whose form factors also preclude them from utilizing the large area of the human body for spatiotemporal sensing or energy harvesting from body movements. E-textiles provide an opportunity to expand on current wearables to enable such applications via the larger surface area offered by garments, but consumer devices have been few and far between because of the inherent challenges in replicating traditional manufacturing technologies (that have enabled these wearable accessories) on textiles. Also, the powering of e-textile devices with battery energy like in wearable accessories, has proven incompatible with textile requirements for flexibility and washing. Although current e-textile research has shown advances in materials, new processing techniques, and one-off e-textile prototype devices, the pathway to industry scale commercialization is still uncertain. This paper reports the progress on the current technologies enabling the fabrication of e-textile devices and their power supplies including textile-based energy harvesters, energy storage mechanisms, and wireless power transfer solutions. It identifies factors that limit the adoption of current reported fabrication processes and devices in the industry for mass-market commercialization.


  • Wireless Ice Detection and Monitoring Using Flexible UHF RFID Tags

    by Mahmoud Wagih, Junjie Shi

    Owing to its low relative permittivity, very few microwave sensors have been developed for monitoring ice deposition. This paper presents the first use of UHF RFID tags for wireless RF ice sensing applications. Despite its low permittivity, the existence of ice as a superstrate on a planar ultra-thin dipole antenna can lower the resonance frequency of the antenna significantly. The RFID tags, having a measured unloaded range of 9.4 m, were evaluated for remotely detecting the formation of ice in various scenarios up to 10 m from the reader, as well as monitoring the ice thawing, based on the Relative Signal Strength (RSS) in a phase-free approach. In most RSS-based sensing approaches, the tag's read-range is reduced as the RSS decreases in response to the stimulant. However, the proposed sensing mechanism does not reduce the tag's range; the ice superstrate improves the impedance matching of the tags and increases their radar cross section (RCS), resulting in a 10 m loaded read-range with over 12 dB ice-sensitivity, in an echoic multi-path environment. The proposed sensing mechanism achieves an accuracy of 86% for tags positioned between 0.5 and 10.5 m with various obstructions. When subjected to line-of-sight metallic obstruction, the sensor still maintains 80% accuracy. The long range and high sensitivity of the proposed sensing mechanics show that UHF RFID is a promising method for detecting the formation of ice in future smart cities.


  • Energy Harvesting Power Supplies for Electronic Textiles

    by Stephen Beeby, Russel Torah, John Tudor, Neil Grabham, Sheng Yong, Sasikumar Arumugam, Yi Li, Junjie Shi

    Electronic textiles (e-textiles or smart fabrics) are textiles that include smart, electronic functionality. Examples include integrated LEDs embedded within yarns [1] , printed functional materials deposited on the surface of the textile [2] and complex flexible circuits woven into the fabric [3] . The supply of power is a key challenge for wearable technologies generally and e-textiles in particular since existing solutions are typically battery powered and the rigid nature of conventional batteries is incompatible with the feel and nature textiles. Alternative power supplies using energy harvesting and wireless power transfer techniques could provide an alternative solution to supply power. Energy harvesting systems also typically require an energy reservoir to provide an energy buffer to accommodate the variations in power supplied from the harvesting solution. Combining flexible energy harvesting techniques with a textile-based energy storage reservoir offers the potential for autonomous textile power supplies suitable for use in future integrated e-textile applications.


  • Open Access

    An easy to assemble ferroelectret for human body energy harvesting

    by Junjie Shi, Sheng Yong, Steve Beeby

    Ferroelectret is a thin and flexible cellular polymer foam that generates electrical power under mechanical force. This paper reports the fabrication and testing of an easy to assemble ferroelectret which is made from two fluorinated ethylene propylene (FEP) films and a standard polymer foam formed into a sandwich structure. The measured piezoelectric coefficient d 33 of the FEP-porous polymer ferroelectret is 1000 pC N −1 . The energy harvester based on the FEP-porous polymer ferroelectret generate an output power of 6.4 μ W. This is corresponding to volume unit power output of 62.4 μ W cm −3 . The practical electromechanical coupling factor is achieved at 0.107. Within 40 s, a 10 μ F capacitor is charged up to 0.2 V by the FEP-porous polymer ferroelectret harvester through a rectifier.